Exhaust Manifold fitting
Discussion
Post on fitting a 4-2-1 janspeed to a s1 111s
"I fitted the S2 type to various S1's - both the Piper flexi and the standard rover six-stud manifold+downpipe.
For the power you have, you're going to be <170 so the 35mm would be the way to go if you want to go with Janspeed.
If it were me, I would buy the piper one for the S2 (fits your car just the same) because you can then fit an S2 exhaust heatshield instead of the brittle board thing you currently have, which you might possibly destroy trying to remove the old manifold.
You can still use the S1 heatshield, but that way you have the option of switching later on.
Remember that to gain access to the 4 nuts that hold the manifold to the downpipe you'll want to remove the heatshield (carefully if you plan to reuse) and also undo the bottom engine mount, then use a jack and/or ratchet strap to pivot the bottom of the engine towards rear of car to gain better access.
If fitting the 4-2-1 type, you may well need to undo the drivers side mount too and pull the engine backwards on a jack in order to get the clearance to wiggle the new manifold in - I have done this only with the cylinder head off which meant there happened to be enough room to do it without moving engine, but only just!"
"I fitted the S2 type to various S1's - both the Piper flexi and the standard rover six-stud manifold+downpipe.
For the power you have, you're going to be <170 so the 35mm would be the way to go if you want to go with Janspeed.
If it were me, I would buy the piper one for the S2 (fits your car just the same) because you can then fit an S2 exhaust heatshield instead of the brittle board thing you currently have, which you might possibly destroy trying to remove the old manifold.
You can still use the S1 heatshield, but that way you have the option of switching later on.
Remember that to gain access to the 4 nuts that hold the manifold to the downpipe you'll want to remove the heatshield (carefully if you plan to reuse) and also undo the bottom engine mount, then use a jack and/or ratchet strap to pivot the bottom of the engine towards rear of car to gain better access.
If fitting the 4-2-1 type, you may well need to undo the drivers side mount too and pull the engine backwards on a jack in order to get the clearance to wiggle the new manifold in - I have done this only with the cylinder head off which meant there happened to be enough room to do it without moving engine, but only just!"
M7RT V said:
I fitted a new manifold to my car the friday before last, not a hard job, just a bit fiddly.
To make your life easier make sure you buy some new studs and nuts as the old ones will more than likely be stuffed.
P.S Be carefull if you're going to be doing it on ramps
Few questions for you!!!To make your life easier make sure you buy some new studs and nuts as the old ones will more than likely be stuffed.
P.S Be carefull if you're going to be doing it on ramps

Did you fit yours with the clam on or off? What method did you use and how long did it take? Could it be done in a day? Also did you have a dodgy moment using ramps?
Cheers
Tom
Tom, you could do it in a day easily. The rear clam can stay on but take the bootlid off as it will make life alot easier.
Use the guide here... http://www.elisenet.com/
My car spat the ramps underneath the car as I was reversing on to them, see topic entitled 'Oh BoLOCs'
Use the guide here... http://www.elisenet.com/
My car spat the ramps underneath the car as I was reversing on to them, see topic entitled 'Oh BoLOCs'

M7RT V said:
My car spat the ramps underneath the car as I was reversing on to them, see topic entitled 'Oh BoLOCs' 
I did that reversing my Westfield up the ramps. Fired both of them forwards, with one getting trapped under the side exhaust breaking the manifold and exhaust bracket. I haven't had the courage to use them again. Anyway take care if using ramps.
I fitted a Larini 4-2-1 to my S1.... TBH trickiest thing was getting the old manifold off.
So long as you remove the oil filter and the lower engine mount so you can swing the engine back outta the way it's an easy job.
Took about 2-evenings (although one of them I made almost NO progress because I thought i'd take the "short cut" of not removing toe oil filter and lower engine mount)
Getting the nuts off the studs will be a pain in the ass, pays to soak them in WD40, pays to put them back together with hi-temp anti-seize.
If you've any specific questions when you're amidst it, please don't hesitate to ask.
Oh, and it'll probably pay to hace a new O2 sensor to go in the new manifold. 20 quid says you'll knacker the old one trying to remove it.
So long as you remove the oil filter and the lower engine mount so you can swing the engine back outta the way it's an easy job.
Took about 2-evenings (although one of them I made almost NO progress because I thought i'd take the "short cut" of not removing toe oil filter and lower engine mount)
Getting the nuts off the studs will be a pain in the ass, pays to soak them in WD40, pays to put them back together with hi-temp anti-seize.
If you've any specific questions when you're amidst it, please don't hesitate to ask.
Oh, and it'll probably pay to hace a new O2 sensor to go in the new manifold. 20 quid says you'll knacker the old one trying to remove it.
Edited by Esprit on Sunday 24th June 11:29
Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff


