Pops and Bangs!! - Wet Plugs....
Pops and Bangs!! - Wet Plugs....
Author
Discussion

Stumason10

Original Poster:

84 posts

236 months

Tuesday 3rd July 2007
quotequote all
Hi All,

been using my S1 as a daily driver for last 4 months and unlike many well loved pets it lives on the street outside my house!

So far been 100% reliable, but, after last nights downpour it was the final straw and today its been misfiring and popping and banging like a good 'un!

Took it local stealer and diagnosed water in the plugs. Quick blow out, new plugs +100 quid fixed it.

Question is, does anyone know of a robust fix, so it will stop the plugs filling with water again? Was thinking of siliconing the plug cover on. But not sure it will take the heat??

Cheers for your help and roll on Nordschlieffe this weekend!

NWTony

3,011 posts

259 months

Tuesday 3rd July 2007
quotequote all
The answer is not to seal the whole cover but to seal the screw holes in it with silicon. I had a similar issue with my S2 and this is what the main dealer did.

Stumason10

Original Poster:

84 posts

236 months

Tuesday 3rd July 2007
quotequote all
I suggested that to the dealer and he said it wouldn't work....Guess he wants repeat business!!

Anything special required or any common silicone sealant??

greysquirrel

786 posts

258 months

Tuesday 3rd July 2007
quotequote all
£100! jeez what a rip off - just keep drying the plug, unless you can get some new plugs that make a better seal around the top - some sealent or grease may stop water getting in but unlikely, just dont take it back to them to be fleeced!

jondude

2,441 posts

248 months

Tuesday 3rd July 2007
quotequote all
Agree with Greysquirrel - stay well clear of this dealer. Amazing he didn't do the job for free as a means of keeping your business - often a squirt of WD40 ( 99p) will do it.

As would you waiting for sun...OK, that can take a lloooong time here.

You could start covering the car - even a cheap cover will keep water out.

It is not too difficult to fabricate a shield for the distributor cap and leads, either. This is more likely the culprit than the leads and wells, as this area is quite unprotected.

I'd go the cover route and have a can of WD40 handy next time.

NWTony

3,011 posts

259 months

Wednesday 4th July 2007
quotequote all
Just any old silicon sealant as far as I know, just fill the screw holes with it. The dealer did mine and I have had no problems since.

Hollywood Wheels

3,689 posts

261 months

Wednesday 4th July 2007
quotequote all
Stumason10 said:
So far been 100% reliable, but, after last nights downpour it was the final straw and today its been misfiring and popping and banging like a good 'un!
You sure you don't own a Sport 160?!! hehe

stevie111s

123 posts

266 months

Wednesday 4th July 2007
quotequote all
The lotus 'approved' technique is to silicon the higher of the two long edges of the spark plug cover. This should fix your problem.

Pete Woolley

15 posts

236 months

Wednesday 4th July 2007
quotequote all
I seem to remember the VX220 had some sort of cover attached to the boot lid so that when it was closed the cover shielded the spark plug area. You could make some sort of deflector plate so the water didn't go near the plugs.

Stumason10

Original Poster:

84 posts

236 months

Wednesday 4th July 2007
quotequote all
Stevie thats what I did last night!! Thanks for the help, common census seems to be S2 head cover plus silicone!! Was thinking of fabricating something, but, no time before ring trip this weekend, also why I allowed myself to get done over by the dealer!

PS. My neighbour has Sport 160 and did sound just the same, except his finally clears it throat at 4k rpm!! Mine just sounded like a chainsaw!! lol!!