S1 wheel bearing change
Discussion
As the man says, you need a big press so best to remove hub DIY and then take to friendly garage. Manual says the hub should be heated before bearing is removed/replaced to expand it slightly but I had one of mine done by a well known independent and they didn't bother. Maybe put the new bearing in the freezer and take to garage in a cool box?
You will need a decent hex key to get the brake calipers undone, and two sorts of special gunk to reassemble so worth finding and reading some instructions first. Oh, and getting the brake shield off can be challenging too, as the little bolt will probably be siezed.
Don't let this put you off, it is DIYable just RTFM and allow time for snags.
AdrianR
You will need a decent hex key to get the brake calipers undone, and two sorts of special gunk to reassemble so worth finding and reading some instructions first. Oh, and getting the brake shield off can be challenging too, as the little bolt will probably be siezed.
Don't let this put you off, it is DIYable just RTFM and allow time for snags.
AdrianR
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
piooly said:
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
So no need to split ball joints etc or did you gloss over that bit?S Works said:
Bearings won't be covered by warranty - wear and tear part I'm afraid. As above, get it to a local garage you trust to take the old one out and fit the new one.
I'm not expecting the warranty to cover the bearings but some do (depends on the level of cover). If the warranty doesn't cover it I'll strip the hubs down and fit the new bearings using the press at work.jamiebae said:
piooly said:
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
So no need to split ball joints etc or did you gloss over that bit?piooly said:
jamiebae said:
piooly said:
its not too bad a job, just take off the brake caliper and disk, use a very long ratchet wrench, as long as possible and take the center hub nut off. Then take the whole assembly to a local garage and get them to press the old one out with a press and fit the new one back in. They only charged me £5 to do that. Then just reassemble and your done. It is an easy job done that way, let them do the hard bit !
So no need to split ball joints etc or did you gloss over that bit?Busy weekend so only got round to calling the dealer today who were more than happy to help, wheel bearings will absolutely be covered under the warranty and the car is booked in next week for them to be sorted (the service manager seemed to think it was the bearings on both sides from my description of the symptoms) along with the MoT.
I'm a happy customer so well done to Dream Machines Lotus in Heathfield, Sussex
I'm a happy customer so well done to Dream Machines Lotus in Heathfield, Sussex

jamiebae said:
Busy weekend so only got round to calling the dealer today who were more than happy to help, wheel bearings will absolutely be covered under the warranty and the car is booked in next week for them to be sorted (the service manager seemed to think it was the bearings on both sides from my description of the symptoms) along with the MoT.
I'm a happy customer so well done to Dream Machines Lotus in Heathfield, Sussex
Nice one! Saves you the hassle.......and it IS a hassle........... I'm a happy customer so well done to Dream Machines Lotus in Heathfield, Sussex

Gassing Station | Elise/Exige/Europa/340R | Top of Page | What's New | My Stuff


