Getting my Mum's desktop t'interwebbed
Getting my Mum's desktop t'interwebbed
Author
Discussion

ehyouwhat

Original Poster:

4,606 posts

249 months

Tuesday 17th July 2007
quotequote all
Hi all,

My mother has decided to join the 21st century and learn how to use a computer - so she's also ordered a BT internet package (with Home Hub thingy).

Their only computer is a desktop, given to them by me a few months ago. It's a reasonable spec but does not have an inbuilt wireless card - I'm therefore popping out tonight to buy her a USB adaptor (are Belkin any good?).

My question concerns setting the network/internet up in the first place. When I did this at my own house (a while ago) I used a desktop, and I needed to physically connect the desktop to the phone line and to the wireless router to set it up - this wasn't a problem as the phone line ran into the same room as the computer.

My mother's desktop is upstairs where there is no phone line, so I anticipate having to dismantle the desktop setup and drag it downstairs to initially set everything up (assuming you still have to physically connect to the router at first).

As an alternative, can I simply take my laptop down there and use that to set everything up? Once the internet and wireless network is up and running, they will then have no problems connecting via their desktop?

They intend to buy a laptop in the next month or two, but want the internet setting up ASAP (think it goes 'live' at 5pm today, though it may already be active).

Any help would be gratefully appreciated as I know bugger all about wireless networks, routers or indeed the internet in general (yet it's me that's lumbered with the job of setting stuff up!)

zcacogp

11,239 posts

275 months

Tuesday 17th July 2007
quotequote all
This isn't going to be what you want to hear, but my folks tried to go this route (USB wireless dongle) and had vast amounts of hassle with it. They ended up buying two, simply because they couldn't make either work (Belkin and Netgear, and their hub is Netgear), and essnetially gave up. They had more problems than most, but I came to the conclusion that USB wireless just isn't worth the hassle.

Best bet is always to run a wire from the machine to the hub. Next best is to get a wireless card and install it properly.

My experience (well, my folks') may be unusual, and we may have been doing something wrong, but it really just seemed to be cr4p technology. Trade off cost against hassle, and I think you'll be looking for a different solution.

(Other Q - I would expect you to be able to set up the hub with your laptop and a network cable, and once it is configured then the desktop machine should be able to pick up the wireless signal. So, no need to lug the desktop machine downstairs.)


Oli.

trooperiziz

9,457 posts

283 months

Tuesday 17th July 2007
quotequote all
zcacogp said:
(Other Q - I would expect you to be able to set up the hub with your laptop and a network cable, and once it is configured then the desktop machine should be able to pick up the wireless signal. So, no need to lug the desktop machine downstairs.)


Oli.
Aye. Or it might be that the homehub will come with wireless already enabled. I know that my BeBox did, and had the wep key stuck to the bottom of the router.

You could always go the homeplug route if you don't want the hassle of wireless.

tigger1

8,486 posts

252 months

Tuesday 17th July 2007
quotequote all
Throw in a wireless card - much better than USB dongle.

If you can avoid using USB for stuff, you probably should...it's just not a great way to go.

K50 DEL

9,788 posts

259 months

Tuesday 17th July 2007
quotequote all
Another small point that I found to my cost yesterday - the majority of wireless USB dongles are USB2 - if your ports are USB1 it won't work.

If it has to be wireless then use a built it pci wireless card

ehyouwhat

Original Poster:

4,606 posts

249 months

Tuesday 17th July 2007
quotequote all
So one of these would be better then? :



http://cgi.ebay.co.uk/Wireless-802-11b-LAN-PCI-Card-WiFi-Network-Desktop-PC_W0QQitemZ120142476408QQihZ002QQcategoryZ45001QQrdZ1QQcmdZViewItem 

Prices seem to be similar(ish)...in fact the PCI card is a bit cheaper.

K50 DEL

9,788 posts

259 months

Tuesday 17th July 2007
quotequote all
ehyouwhat said:
So one of these would be better then? :



http://cgi.ebay.co.uk/Wireless-802-11b-LAN-PCI-Card-WiFi-Network-Desktop-PC_W0QQitemZ120142476408QQihZ002QQcategoryZ45001QQrdZ1QQcmdZViewItem 

Prices seem to be similar(ish)...in fact the PCI card is a bit cheaper.
That's the bad boy

ehyouwhat

Original Poster:

4,606 posts

249 months

Tuesday 17th July 2007
quotequote all
Okay, cheers all for the advice. thumbup

I'll go and pick one of those up later on.

mystomachehurts

11,669 posts

281 months

Tuesday 17th July 2007
quotequote all
Also, since you are going the wireless route, download a copy of NetStumbler it will give you a list of all the other Wireless Networks running in the area.

You can then ensure that you pick a Wireless Channel that is not in use in the neighbourhood. (If they live in the sticks, likely this won't be an issue).

Also consider WPA for securing the wireless link.

Personally I'd try to run CAT5 long before I'd consider wireless... takes two seconds to drill a hole through a couple of window surrounds and you are guaranteed to have a safe, secure and reliable link back to the router, I've done it even to the point of getting a hearty sting from a nearby electric fence!

Wireless should always be a last resort, especially in an urban environment.


bobthemonkey

4,216 posts

247 months

Tuesday 17th July 2007
quotequote all
Homehub also supports setup and use by USB. Drivers come on the CD. ETA is doesnt come with a cable IIRC. You need to use the smaller usb connector, not the regular one on the hub.

Edited by bobthemonkey on Tuesday 17th July 17:00

ehyouwhat

Original Poster:

4,606 posts

249 months

Tuesday 17th July 2007
quotequote all
Well PCI card bought and installed now, and the Home Hub has been plugged in as per the instructions. Apparently it takes the Hub a certain amount of time to properly connect to the broadband service, so I have to wait until the Wireless and Broadband lights are static green. The instructions say that this usually takes an hour or so - but can take up to 24 hours - so I waited an hour at my Ma's house and then decided to call in again tomorrow to see if it's sorted yet.

I'm not 100% confident that the 'service' has actually been activated yet, even though the BT automated service has advised usn that it is - I had problems when I set up my own stuff last year. If the light is still not static green tomorrow afternoon when I visit my Mum, then I'll call BT and ask them the score.

Reading briefly through the instructions it seems that the new Home Hub does NOT need physically connecting to the computer to set up, so that's handy. Likewise the new PCI wireless card is 'detecting' a 'Home Hub' network quite strongly, so I'm assuming (rightly or wrongly) that, as the Wireless light is lit up on the Home Hub, it is probably our network that it is detecting.

Hopefully it won't be as much of a pain to set up as my own stuff was last year.

zcacogp

11,239 posts

275 months

Wednesday 18th July 2007
quotequote all
A bit of a general comment, but I was surprised by how easy it was to set up broadband for me at home - really little hassle (although that was with a wired modem/router.)

Having said that, setting up wireless was (for me) pretty easy too. (Once I had remembered to turn on the wireless function on my lappie silly )


Oli.

ehyouwhat

Original Poster:

4,606 posts

249 months

Wednesday 18th July 2007
quotequote all
Well called my mum (a technophobe) up this morning and it seems that the situation remains the same - the 'Wireless' light is solid green, the 'Broadband' light is constantly flashing, and there are no other lights on - this is how I left it yesterday afternoon. So the Broadband service has not been activated in the last 17 hours (BT say it should take around an hour, but can take up to 24 hours).

I shall wait until this afternoon and then go and inspect the situation myself. If there is still no broadband indication then I shall test the hub in the hall (to see if the extention to the living room is causing the problem).

Quick question: The main household phone line comes in to the hall. There is then a proper BT extention that runs to the living room. The intention is to have the Home Hub in the living room as it can fit in with its surroundings a bit better there. Should I plug in ADSL filters to both the original phone socket and the extention phone socket, or should I just plug one into the original phone socket and then plug the extention wire in on top of that? I.e. do I need to use two filters or just the one, and could using the wrong number cause the 'Broadband' light not to come on?

This is proving far more 'faffy' than I was hoping. I ordered the BT broadband package for my mum at the beginning of the month, knowing that I was relocating 300 miles at the end of the month and so wanted to have everything up-and-running (and problems ironed out) before I left...300 miles is a long way to travel of an evening just to sort out my mum's internet.

The activation date she was given was nine days after we had ordered it, and the Home Hub was delivered on the activation date too. On inspection the clips on the bottom of the Home Hub (that open and close the port access panel) are snapped, so this is obviously a dodgy Home Hub in the first place (it's one of the new black ones though, so I shouldn't imagine it is 'used'). I thought I would test the Hub anyway as, if it works fine, we're not really bothered about a couple of snapped clips. Added to which, I wasn't sure we'd have time (before I relocated) to get in touch with BT and get them to send us a replacement Home Hub.

As it turns out - if we can't get the Hub to connect to the Broadband service - then we'll have to send the Hub back anyway.

zcacogp

11,239 posts

275 months

Wednesday 18th July 2007
quotequote all
you said:
Quick question: The main household phone line comes in to the hall. There is then a proper BT extention that runs to the living room. The intention is to have the Home Hub in the living room as it can fit in with its surroundings a bit better there. Should I plug in ADSL filters to both the original phone socket and the extention phone socket, or should I just plug one into the original phone socket and then plug the extention wire in on top of that? I.e. do I need to use two filters or just the one, and could using the wrong number cause the 'Broadband' light not to come on?
Not quite sure that I follow this, but the usual game is to only put filters on the end of the lines, where the telephone and/or home hub plugs in to the line (it makes no matter whether this line is an extension in the house or not.)

Therefore, at a guess from your description, you need to put a filter on the end of the extension in the living room, and into this filter plug the home hub (and a telephone, if you have one there already. The filter also works as a splitter.)

You will also need to put a filter in on any other telephones you have in the house as well, but not on any sockets with don't have anything plugged into them.

Hope this helps.


Oli.

ehyouwhat

Original Poster:

4,606 posts

249 months

Wednesday 18th July 2007
quotequote all
zcacogp said:
you said:
Quick question: The main household phone line comes in to the hall. There is then a proper BT extention that runs to the living room. The intention is to have the Home Hub in the living room as it can fit in with its surroundings a bit better there. Should I plug in ADSL filters to both the original phone socket and the extention phone socket, or should I just plug one into the original phone socket and then plug the extention wire in on top of that? I.e. do I need to use two filters or just the one, and could using the wrong number cause the 'Broadband' light not to come on?
Not quite sure that I follow this, but the usual game is to only put filters on the end of the lines, where the telephone and/or home hub plugs in to the line (it makes no matter whether this line is an extension in the house or not.)

Therefore, at a guess from your description, you need to put a filter on the end of the extension in the living room, and into this filter plug the home hub (and a telephone, if you have one there already. The filter also works as a splitter.)

You will also need to put a filter in on any other telephones you have in the house as well, but not on any sockets with don't have anything plugged into them.

Hope this helps.


Oli.
Yeah sorry, just to clarify: The socket in the hall is the main BT socket that the house was built with. The only thing plugged into this socket is an extention cord that goes through to the living room and leads to an extention box in the wall. It is into this box that the only phone in the house is plugged. It is also into this socket that my mum wishes the Home Hub to be plugged. There is no 'phone' plugged into the main BT socket in the hall, only an extention lead for the living room (in which the main phone is). So the question is, do I need to plug a filter into this socket (i.e. the extention socket in the living room, with the house phone also plugged into the filter), or do I need to plug a filter into the original BT socket in the hall (with the extention lead for the living room plugged into the filter)...or both?!

I can't think of how to write it more simply, my brain isn't working too well today hehe

zcacogp

11,239 posts

275 months

Wednesday 18th July 2007
quotequote all
Don't worry - a diagram often helps no end!

BUT, from your description, if you were to plug a filter into the socket in the hall, then plug the extension into the filter, the extension would be ONLY carrying telephone signals (as opposed to broadband signals) as it would be plugged into the telephone side of the extension. Therefore, if you were to plug the home hub into the socket in the living room, it wouldn't be able to connect to the broadband system.

You need to leave the socket in the hall as it is, then plug a filter into the socket in the living room, and into this filter plug both the home hub and the existing telephone.


Oli.

ehyouwhat

Original Poster:

4,606 posts

249 months

Wednesday 18th July 2007
quotequote all
zcacogp said:
Therefore, if you were to plug the home hub into the socket in the living room, it wouldn't be able to connect to the broadband system.

You need to leave the socket in the hall as it is, then plug a filter into the socket in the living room, and into this filter plug both the home hub and the existing telephone.


Oli.
A-ha. I think we've found the source of the problem......my stupidity!

Much appreciated.

zcacogp

11,239 posts

275 months

Wednesday 18th July 2007
quotequote all
Glad to be of help ... I thought I was just commenting on the placing of filters, not actually finding the source of the troubles you are having with the connection!

Glad it works. (Or that you are on the way to getting it to work.)


Oli.

ehyouwhat

Original Poster:

4,606 posts

249 months

Wednesday 18th July 2007
quotequote all
zcacogp said:
Glad to be of help ... I thought I was just commenting on the placing of filters, not actually finding the source of the troubles you are having with the connection!

Glad it works. (Or that you are on the way to getting it to work.)


Oli.
I've not been and tried it yet, but as the Broadband light is still flashing now (24 hours later) I'd say that the placing of the filters is likely to be a contributory factor.

I'll report back later and let you all know how I've got on.

thumbup

ehyouwhat

Original Poster:

4,606 posts

249 months

Thursday 19th July 2007
quotequote all
Well removing the ADSL filter from the main BT socket in the hall (paperbag) did the trick, and the Broadband light came on a solid green colour.

For whatever reason the Hub did not detect the wireless card at first, so I had to physically connect the computer and the Hub with a cable (which meant dragging the PC downstairs into the living room). Setup was dead easy after that though - far easier than it had been to set my own wireless network up last year.

Internet is running lovely for her now. I still think it's a bit naff that the Home Hub came with snapped clips though!

Cheers everyone for your help and suggestions!