Changing Rad Fan
Author
Discussion

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
Do i need to remove the radiator to get at the fan. Or does it come off without doing so? If so it looks like i could do it without removing the clamshell going by this pic on techwiki, Anyone tried it? Its an s1 i have, only has a single fan not a double so i think it might fit between the gap in the grill


http://wiki.seloc.org/images/5/50/Remove_front_cla...



Edited by porteouz on Thursday 2nd August 00:03

ptp170

277 posts

238 months

Thursday 2nd August 2007
quotequote all
To be honest it's only a 5-10 min job undoing the radiator cowling and poping off the hoses.
It's a good idea to put new heavy duty jubilee clips on the hoses with a bit of threadlock so avoid the 'hose pop-off' issue in the future! If you do this then you will need to bleed the air from the system. On my S2 one of the bleed points was on the n/s hose by the rad...but I can't see on on yours....maybe it's somewhere else on the S1???

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
According to manuals its in the same place as you mentioned. You took the rad out without removing the front clam?

ptp170

277 posts

238 months

Thursday 2nd August 2007
quotequote all
Soz....just realised thats NOT a pic of your car biglaugh

In that case you wouldn't be able to remove the fan as the toeing eye bar is in the way and that can only be removed with the clam off (as far as I'm aware!!)

If you do remove the clam be prepared for many rusted nut bolts and hours of swearing!!

Just out of interest why are you removing the fan??? Broken I assume?

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
Yea my fan wont start. Tried testing it by removing the relay and shorting the connections. Guess it must be Knackered, Its not seized as ive had my hand in and spun it so i guess its burnt out. Was going to try and wire the fan straight to the battery to see if it started but i think i should just bite the bullet and get the clam off. NOT looking forward to it, as you said i can see every bolt being tight!

ptp170

277 posts

238 months

Thursday 2nd August 2007
quotequote all
On my S2 there was an inline connector plug about 5-ish inches along from the fan...if you can get to that via the grill aperture (or maybe from above?) you can power the fan from there!! Removing the clam should be a last resort!! It maybe a fuse in the fusebox or a faulty temperature sender instead!!

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
Ive checked the fuse's. Even if it was a faulty temp sender, me shorting at the relay should still start it as the temp sender would be by-passed i think? Im no Electrician but i think thats right? Ill maybe try and get at that connector your talking about as i really dont want to take that clam off

ptp170

277 posts

238 months

Thursday 2nd August 2007
quotequote all
Might even be that actual connector as it would be exposed to all manor of nasty outdoor things in that area!! I had loads of corroded connectors on my S2, I just chopped then and replaced with new ones then silcone sealed them up!!

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
Can sumone tell me, Is it the blue plug or the brown plug which turns the fan on?

ptp170

277 posts

238 months

Thursday 2nd August 2007
quotequote all
Blue sender is for the display on the Stack unit. Brown is for the ECU, as far as I'm aware ECU controls the fan as well, so it's the brown one you want.

Wouldn't recommend shorting it out to see if you can get the ECU to trigger the fan though!!

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
Just wondered what one it was. If it didnt start with the relay shorted out then its either the fan itself or electrics, Maybe the plug you mentioned. CHeers m8

cccscotland

418 posts

285 months

Thursday 2nd August 2007
quotequote all
Pull the fan relay out and short it. If it comes on you're looking at electrics. If it doesn't (and I've done this!) it's clamshell off time.
Good luck
Matt

Promised Land

5,426 posts

240 months

Thursday 2nd August 2007
quotequote all
from my experience if the fan isnt working you just need a new fan motor, i did last year.

this can be changed from the front grill opening, not easy (so the lotus mechanic told me) and the fan motor was quite expensive (£150ish) but i had it done as a freebie due to other problems theyd cocked up on wink

usually they sieze because the rad or a pipe is leaking coolant onto them so you might want to check everywhere before changing it to make sure it doesnt happen again

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
it isnt seized because ive i said above ive spun it with my hands. Could it just be that the motor has burnt out? is this a common thing?

Promised Land

5,426 posts

240 months

Thursday 2nd August 2007
quotequote all
porteouz said:
Could it just be that the motor has burnt out? is this a common thing?
yes buy that first then take it from there if it isnt the relay as said above

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
Ok i managed to wire the fan straight to the battery and it started biggrin so thats a result. Am i right in thinking that if it didnt start by shorting the relay then there must be a break between the relay and the fan, either a wire or a plug? Or can the temp sender still stop it from working? Also does anyone know where i would get a wiring diagram?

ptp170

277 posts

238 months

Thursday 2nd August 2007
quotequote all
Where did you power the fan up from ??? the relay socket or that plug by the fan that i was on about???

porteouz

Original Poster:

123 posts

235 months

Thursday 2nd August 2007
quotequote all
the plug that you were on about, just went straight from there to the battery. As i said it wouldnt go from the relay