RAM upgrade problems
Author
Discussion

Black5

Original Poster:

579 posts

254 months

Monday 13th August 2007
quotequote all
We have an IBM server (eServer X-series 206, Type 8482). Currently running 1GB of RAM as a bank of 4x 256mb chips.

We have purchased 4x 512mb chips in order to upgrade to 2GB.

Simply replacing the chips did not work. When starting up we get 3x 3 beeps signifying incompatable.

After some research, I found you need to reset the motherboard - I don't get this bit, but the computer tech knew what he was doing. No - still don't work.

I have checked all the chip info is correct (DDR PC2700 CL2.5 ECC 184pin etc). The motherboard supports up to 4GB RAM, so that's not the problem.

The memory is Crucial - so a good brand.

What's the problem????

ginettag27

7,169 posts

300 months

Monday 13th August 2007
quotequote all
I don't have any experience of carrying this out with a server, but have done so on many PCs... Mostly they want you to go in to the CMOS setup, on Boot, to confirm the new amount of memory installed. Save this and it should be okay.. Not sure if an eServer works the same way.

IBM's support is usually quite good see here, for installations movies,hope they help!

http://www-304.ibm.com/jct01004c/systems/support/s...

(second link in main part of the page)

or here for a full installation manual...

http://www-304.ibm.com/jct01004c/systems/support/s...


Added : After looking around, there are different models of teh 8482, which one have you got? One wants 332MHz memory modules and the other wants 400MHz... How did you identify the memory you bought from Crucial?


Edited by ginettag27 on Monday 13th August 13:55

ginettag27

7,169 posts

300 months

Monday 13th August 2007
quotequote all
There's a bit more from the second link...

From page 72 of the manual. The numbers should be the number of beeps.. and then it gives a desc of what it thinks is the problem and what to try and do to resolve it.

3-2-4 (Failure comparing CMOS memory size against actual) 1. DIMM 2. Battery 3. System board
3-3-1 (Memory size mismatch occurred.) 1. DIMM 2. Battery 3. System board
3-3-2 (I2C bus error occurred) v Disconnect server power, wait 30 seconds, and retry. v System board
3-3-3 (No memory installed) 1. Install or reseat the memory modules. 2. DIMMs. 3. System board.

Are you still getting the same error, even once the Tech. updated the CMOS or is there now a new error/beep?

ginettag27

7,169 posts

300 months

Monday 13th August 2007
quotequote all
More from the manual...

Installing a memory module The following notes describe the types of dual inline memory modules (DIMMs) that the server supports and other information that you must consider when installing DIMMs: v The server supports industry-standard PC2700 and PC3200 double-data-rate (DDR) dual inline memory modules (DIMMs). v The system board contains four DIMM connectors and supports two-way memory interleaving. v The DIMM options available for the server are 256 MB, 512 MB, and 1 GB. The server supports a minimum of 256 MB and a maximum of 4 GB of system memory. v The amount of usable memory will be reduced depending on the system configuration. A certain amount of memory must be reserved for system resources. The BIOS will display the total amount of installed memory and the amount of configured memory. v The server comes with one 256 MB or 512 MB DIMM installed in the DIMM 1 memory connector. If the server has one DIMM installed, when you install an additional DIMM, it must be installed in the DIMM 3 memory connector, and it must be the same size, speed, type, and technology as the DIMM that you installed in the DIMM 1 memory connector. You can mix compatible DIMMs from various manufacturers. When one DIMM is installed, the server runs as a single-channel server. When you add a DIMM in DIMM 3 memory connector, the server becomes a dual-channel server. v DIMMs must be installed in matched pairs. The first pair of DIMMs you install in DIMM 1 and DIMM 3 memory connectors must be the same size, speed, type, and technology. You can mix compatible DIMMs from various manufacturers. If you install a second pair of DIMMs in DIMM 2 and DIMM 4 memory connectors, they do not have to be the same size, speed, type, and technology as the DIMMs installed in the DIMM 1 and DIMM 3 memory connectors. However, the size, speed, type, and technology of the DIMMs you install in DIMM 2 and DIMM 4 memory connectors must match each other. Note: Installing a third DIMM without installing a fourth DIMM to make a pair is not supported. v Install only 2.5 V, 184-pin, double-data-rate (DDR), PC2700 or PC3200, unbuffered synchronous dynamic random-access memory (SDRAM) with error correcting code (ECC) DIMMs. These DIMMs must be compatible with the latest PC2700 and PC3200 SDRAM unbuffered DIMM specification. For a list of supported options for the server, go to http://www.ibm.com/us/compat/; then, select your country and navigate to the list of options for the server. v When you restart the server after adding or removing a DIMM, the server displays a message that the memory configuration has changed.

Complete the following steps to install a DIMM:
1. Read “Installation guidelines” on page 23 and the safety information beginning at “Safety information” on page 107.
2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables.
3. Remove the side cover (see “Removing the side cover” on page 26).
4. Remove the support bracket (see “Removing and installing the support bracket” on page 28).
5. Locate the DIMM connectors on the system board. Determine the connectors into which you will install the DIMMs. Install the DIMMs in the sequence shown in the following table. Memory installation sequence DIMMs Slots 1 DIMM 1 2 DIMMs 1, 3 3 DIMMs Not supported 4 DIMMs 1, 2, 3, 4 Attention: To avoid breaking the retaining clips or damaging the DIMM connectors, open and close the clips gently. 6. Open the retaining clips and, if necessary, remove any existing DIMM. 7. Touch the static-protective package containing the DIMM to any unpainted metal surface on the server. Then, remove the new DIMM from the package. 8. Turn the DIMM so that the DIMM keys align correctly with the slot. 9. Insert the DIMM into the connector by aligning the edges of the DIMM with the slots at the ends of the DIMM connector. Firmly press the DIMM straight down into the connector by applying pressure on both ends of the DIMM simultaneously. The retaining clips snap into the locked position when the DIMM is firmly seated in the connector. If there is a gap between the DIMM and the retaining clips, the DIMM has not been correctly installed. Open the retaining clips, remove the DIMM, and then reinsert it.

ginettag27

7,169 posts

300 months

Monday 13th August 2007
quotequote all
and there's more...

3-1-3 (RAM test failed above address OFFFFH)) 1. DIMM 2. System board

Plus, these steps to check... But I guess you'd have an error message to report..

201-XXX-0nn (Failed memory test.) 1. DIMM Location slots 1-4 where nn = DIMM location. Note: nn 1=DIMM

or these steps to check further... It's probably easier to read it from the Support manual, link already posted.

Memory problems Symptom FRU/action The amount of system memory displayed is less than the amount of physical memory installed. 1. Verify that: v The memory modules are seated properly. v You have installed the correct type of memory. v If you changed the memory, you updated the memory configuration with the Configuration/Setup Utility program. v All banks of memory on the DIMMs are enabled. The server might have automatically disabled a DIMM bank when it detected a problem or a DIMM bank could have been manually disabled.2. Check POST error log for error message 289: v If the DIMM was disabled by a system-management interrupt (SMI), replace the DIMM. v If the DIMM was disabled by the user or by POST: a. Start the Configuration/Setup Utility program. b. Enable the DIMM. c. Save the configuration and restart the server.3. DIMM. 4. System board.

Black5

Original Poster:

579 posts

254 months

Tuesday 14th August 2007
quotequote all
Thanks for the info.

Hopefully we should get it sorted.