nero ? burn probs
Author
Discussion

tali1

Original Poster:

5,286 posts

232 months

Tuesday 14th August 2007
quotequote all
when burning with nero it always freezes at 3% process state and 8% buffer level and the error message is SCSI COMMAND ABORTED.
This is even at low burn speeds and the cd drive is not reading any cd-rs discs either
checked device manager and settings everything seems fine.
Tried copying with built in In Cd- and it burned the disc- BUT it wont read it either in my dvd or cd drive (my dvd drive reads other discs fine)
any ideas? is it a hardware or software prob?

Trooper2

6,676 posts

262 months

Tuesday 14th August 2007
quotequote all
I have to assume this issue is with an external DVD burner, a quick Google reveals that there is a major problem with Nero and USB2, can you connect your drive via Firewire? That may cure it.

If you can't or it is an internal drive go to:

http://forum.videohelp.com/

http://forums.afterdawn.com/
or
http://club.cdfreaks.com/

and search for "SCSI Command Aborted" to look for an answer. It appears that there are quite a few solutions to the problem depending on your hardware and software set-up.

tali1

Original Poster:

5,286 posts

232 months

Wednesday 15th August 2007
quotequote all
thanks trooper2 but both drives are internal NOT external , dunno if thats of any further help

dern

14,055 posts

310 months

Wednesday 15th August 2007
quotequote all
Why don't you contact their tech support people?

ThePassenger

6,962 posts

266 months

Wednesday 15th August 2007
quotequote all
A) Try their tech support.
B) You're writer is shagged.
C) The disks are shagged.

It will be either B or C.

Trooper2

6,676 posts

262 months

Wednesday 15th August 2007
quotequote all
tali1 said:
thanks trooper2 but both drives are internal NOT external , dunno if thats of any further help
Try updating the firmware for your CD/DVD drive(s), Replace the ribbon cable that connects the drives to the Motherboard (borrow one if you can to test).

tali1

Original Poster:

5,286 posts

232 months

Wednesday 15th August 2007
quotequote all
nero tech "support" only gives automated responses -even i know that ffs!!!
Trooper your solution too complcated for my limited tech ability frown

ThePassenger

6,962 posts

266 months

Wednesday 15th August 2007
quotequote all
tali1 said:
nero tech "support" only gives automated responses -even i know that ffs!!!
Trooper your solution too complcated for my limited tech ability frown
Ignoring the firmware option. Personally, I'd put that on the same level as flashing a BIOS. Yes, there are utilities that make it really easy. Conversely, they've made it easier to turn you PC, CD-ROM, DVD-whatever in to a something that closely resembles a boat anchor.

Swapping the cable is cheap enough. Now, if you're saying THAT's too complex... you have problems because I foresee a screwdriver in your near future. It will be either a small thing or a thick flat thing (SATA or IDE) swap the cable, it only goes in one way, if nowt different... there ya go.

Reinstalling Nero is a possibility, but I have doubts it'll fix a SCSI/ATAPI error, usually those are generated by the burner itself.

Buy a set of disks, track down say... Ritek G04 dyed units. They were the most compatible I heard of a few years ago. If it still fails...

Go to PC World/Dabs/Scan/Novatech buy yourself a new DVD drive (costs about £23). Swap it for the old one. Go. I will wager that magically, the fault has vanished. It takes 30min for an utter n00b to do and to be quite honest poking around the engine bay of a car is far more difficult than the insides of your PC; because nothing is using high voltage or capable of ripping your arm off.

If you are honestly saying swapping the cable is too much, you have one other choice. Go buy a new PC. Or accept that fact your burner is on the way out and don't burn disks any more.

Edited by ThePassenger on Wednesday 15th August 22:37