lightened & balanced flywheel for a 968 cs
lightened & balanced flywheel for a 968 cs
Author
Discussion

jdubbya

Original Poster:

22 posts

230 months

Friday 2nd November 2007
quotequote all
morning folks,

any info/advice on lightened flywheels on 968 cs's?
i've heard rumors, but can't seem to find any info on them.

cheers

jdubbya

nick_968

560 posts

269 months

Friday 2nd November 2007
quotequote all
Aftermarket are single mass rather than dual mass. Lots of weight to be saved, but also comes at a cost of some vibrations at certain rpm. If you want a quality item try 9m. If you want cheaper try Fidanza in the US. Fidanzas are known to transmit vibes to the transaxle at certain rpm for sure. The 9m unit I cannot comment, but their stuff tends to be a lot better quality than most.

willdew

2,138 posts

295 months

Friday 2nd November 2007
quotequote all
Yep, as Nick says, the single mass ones save a fair bit of weight, and of course this saving is magnified as the engine will spin more freely.

For more 968 specific questions like this though, you'll have a lot more luck posting on the forum of the www.porsche968uk.co.uk site. Also, do a search on there, and you'll find various sources of the single mass units.

thegoose

8,077 posts

241 months

Friday 2nd November 2007
quotequote all
I happened to get talking about this with the Porsche Club GB championship co-ordinator about this at their track day on Tuesday (no 968s there at all!). Turns out Porsche used to do a single mass unit but ended production. This wasn't good news for the guys that race them so Porsche were asked to make some...except they couldn't find the plans. Subsequently one was removed from one of the race cars and sent over to them so they could plan to copy it - kind of reverse engineering on your own product! I think the final outcome was that they didn't manufacture any or the cost was prohibitive.

There is another one being put forward for approval for the championship, which I think is the American one. Speak to EMC Motorsport in the midlands about it, it's them who are involved and will probably be supplying it.

willdew

2,138 posts

295 months

Friday 2nd November 2007
quotequote all
thegoose said:
Speak to EMC Motorsport in the midlands about it, it's them who are involved and will probably be supplying it.
Tel: 0121 3282225

nick_968

560 posts

269 months

Friday 2nd November 2007
quotequote all
Yes your right about the Motorsports flywheel, the 9m is probably the closest you get to a copy. Personally I wouldnt put a Fidanza unit on my car as they are not that great. But you pay your money and take your choice as the Fidanza is half the price and probably ok for racing just noisy on the road.

thegoose

8,077 posts

241 months

Friday 2nd November 2007
quotequote all
nick_968 said:
Yes your right about the Motorsports flywheel, the 9m is probably the closest you get to a copy. Personally I wouldnt put a Fidanza unit on my car as they are not that great. But you pay your money and take your choice as the Fidanza is half the price and probably ok for racing just noisy on the road.
Now I'm curious to know how solid flywheels can vary in terms of noise.........confused

nick_968

560 posts

269 months

Friday 2nd November 2007
quotequote all
Balance.......and weight.....does that make sense?

willdew

2,138 posts

295 months

Friday 2nd November 2007
quotequote all
nick_968 said:
Balance.......and weight.....does that make sense?
From what I understand, it's not the flywheel that's noisy, it's that a heavier, dual mass flywheel acts as a damper on the vibration/resonance the torque tube otherwise has at certain engine speeds. The lighter flywheel doesn't have this damping effect.

Edited by willdew on Friday 2nd November 10:57

thegoose

8,077 posts

241 months

Friday 2nd November 2007
quotequote all
I understand this, in terms of the difference between single & dual mass:
willdew said:
From what I understand, it's not the flywheel that's noisy, it's that a heavier, dual mass flywheel acts as a damper on the vibration the torque tube otherwise has. The lighter flywheel doesn't have this damping effect.
However, your point was Nick, that one type of single mass wheel was noisier than another. Hard to understand from your brief response but do you mean there are weight differences between the 9M and Fidanza wheels and they are balanced differently?

willdew

2,138 posts

295 months

Friday 2nd November 2007
quotequote all
thegoose said:
I understand this, in terms of the difference between single & dual mass:
willdew said:
From what I understand, it's not the flywheel that's noisy, it's that a heavier, dual mass flywheel acts as a damper on the vibration the torque tube otherwise has. The lighter flywheel doesn't have this damping effect.
However, your point was Nick, that one type of single mass wheel was noisier than another. Hard to understand from your brief response but do you mean there are weight differences between the 9M and Fidanza wheels and they are balanced differently?
When EMC rebuilt my engine they balanced my standard dual mass flywheel (although in balancing it, it turned out to be almost perfect already), which makes it difficult to imagine them fitting a new single mass wheel that might have balance issues without checking it and rectifying them if necessary.

nick_968

560 posts

269 months

Friday 2nd November 2007
quotequote all
Yes there are weight differences, the Fidanza is lighter. I cannot comment on the specific differences, but 9m claim to have little or no vibe issues (this was a while back so memory may not be 100% maybe Colin can confirm) on theirs, but I know a lot of people who have been unhappy with the vibes from the Fidanza over the years. Only put it on if you dont mind these effects. DMF should be balanced already pretty good as Will has pointed out his didnt need much doing. Question is....do you really need a lightened flywheel?

willdew

2,138 posts

295 months

Friday 2nd November 2007
quotequote all
nick_968 said:
Question is....do you really need a lightened flywheel?
Not when you've got a turbo charger... wink

nick_968

560 posts

269 months

Friday 2nd November 2007
quotequote all
Well.....do you really need a turbo charger?