MAF Sensor
Author
Discussion

drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all
How long do these things last in general - it looks like I've done 2 in 12 months! Is there any way of preserving the poor things or at least buying them cheap in bulk!!?

USS Bozeman

1,084 posts

253 months

Monday 12th November 2007
quotequote all
drhildr said:
How long do these things last in general - it looks like I've done 2 in 12 months! Is there any way of preserving the poor things or at least buying them cheap in bulk!!?
2 in 12 Seems excessive - I am on the original (996) and mines a 2002 car (35k miles)
I think it might need replacing but I just clean it & its fine for a few k more miles.

996TT_STEVO

4,078 posts

259 months

Monday 12th November 2007
quotequote all
If your putting down big power they will pop all the time, something to do with electical surges in high HP motors, unless your running an oiled filter and the MAF is not working correctly. There is an Hitachi MAF currently being used but it has to have ECU programming with it. It has been showing great results!

drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all
Ruf Modified 640bhp - I am using a oiled panel filter (presume this is OK?)


996TT_STEVO said:
If your putting down big power they will pop all the time, something to do with electical surges in high HP motors, unless your running an oiled filter and the MAF is not working correctly. There is an Hitachi MAF currently being used but it has to have ECU programming with it. It has been showing great results!

996TT_STEVO

4,078 posts

259 months

Monday 12th November 2007
quotequote all
drhildr said:
Ruf Modified 640bhp - I am using a oiled panel filter (presume this is OK?)


996TT_STEVO said:
If your putting down big power they will pop all the time, something to do with electical surges in high HP motors, unless your running an oiled filter and the MAF is not working correctly. There is an Hitachi MAF currently being used but it has to have ECU programming with it. It has been showing great results!
K&N Filter? Are you Oiling it?

drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all
Yes and Yes!

996TT_STEVO said:
drhildr said:
Ruf Modified 640bhp - I am using a oiled panel filter (presume this is OK?)


996TT_STEVO said:
If your putting down big power they will pop all the time, something to do with electical surges in high HP motors, unless your running an oiled filter and the MAF is not working correctly. There is an Hitachi MAF currently being used but it has to have ECU programming with it. It has been showing great results!
K&N Filter? Are you Oiling it?

clubsport

7,420 posts

289 months

Monday 12th November 2007
quotequote all
There is a good chance the oil contamination is the cause for the early demise of your Mafs....this is one reason I run paper filters (I have 1/2 your bhp though!)

996TT_STEVO

4,078 posts

259 months

Monday 12th November 2007
quotequote all
Stop Oiling it, when I run my K&N 3/4 years ago, I had similar issues when oiling myself, you want to just use the pre-oiled version from new and don't oil again and you will be good!

I'm still putting money on it that your blowing them due to the power hike, did you blow them in hotter weather also?. I'm running 570/580ish and I blew 2 in summer, 1 South France and other at SPA.

drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all
I'll give this a go - what about after cleaning?

Hard to say when it went - became very evident yesteday at Vmax - down by 20mph on normal. Diagnostics showed maf low but within parameters but no other faults to point a finger at.


996TT_STEVO said:
Stop Oiling it, when I run my K&N 3/4 years ago, I had similar issues when oiling myself, you want to just use the pre-oiled version from new and don't oil again and you will be good!

I'm still putting money on it that your blowing them due to the power hike, did you blow them in hotter weather also?. I'm running 570/580ish and I blew 2 in summer, 1 South France and other at SPA.

derestrictor

18,764 posts

292 months

Monday 12th November 2007
quotequote all
MAF or no MAF, David, your yellow peril is consistently the nicest 'off the line firer' at VMax events.

The car looks a million dollars - as do all 996GT2s - but the neatness with which you seem to step away from all comers is an inspirational sight: little if any wheelspin, just an heroic downing of hunk precusring the most brutal of lunges forward... yes, that car lunges like nothing this side of Guy R's car.

Simply magnificent. beer

drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all
Thanks mate! That was the only consolation I took away from yesterday - no one beat the old girl off the line and she was very sick!

derestrictor said:
MAF or no MAF, David, your yellow peril is consistently the nicest 'off the line firer' at VMax events.

The car looks a million dollars - as do all 996GT2s - but the neatness with which you seem to step away from all comers is an inspirational sight: little if any wheelspin, just an heroic downing of hunk precusring the most brutal of lunges forward... yes, that car lunges like nothing this side of Guy R's car.

Simply magnificent. beer

996TT_STEVO

4,078 posts

259 months

Monday 12th November 2007
quotequote all
drhildr said:
I'll give this a go - what about after cleaning?

Hard to say when it went - became very evident yesteday at Vmax - down by 20mph on normal. Diagnostics showed maf low but within parameters but no other faults to point a finger at.


996TT_STEVO said:
Stop Oiling it, when I run my K&N 3/4 years ago, I had similar issues when oiling myself, you want to just use the pre-oiled version from new and don't oil again and you will be good!

I'm still putting money on it that your blowing them due to the power hike, did you blow them in hotter weather also?. I'm running 570/580ish and I blew 2 in summer, 1 South France and other at SPA.
On most occasions a completely blown MAF will show an ABS/PSM Warning light when completely blown, so I would look at cleaning or replacing the MAF. You want to use something like IPA to spray it with so there is no film/residue left over. Good Luck!

markbe

1,755 posts

257 months

Monday 12th November 2007
quotequote all
drhildr said:
How long do these things last in general - it looks like I've done 2 in 12 months! Is there any way of preserving the poor things or at least buying them cheap in bulk!!?
Now come on Dave; change back to a petrol derivative from your current methanol mix and all will be fine.hehe

Markbiggrin

Edited by markbe on Monday 12th November 12:10

Vesuvius 996

35,829 posts

302 months

Monday 12th November 2007
quotequote all
996TT_STEVO said:
drhildr said:
I'll give this a go - what about after cleaning?

Hard to say when it went - became very evident yesteday at Vmax - down by 20mph on normal. Diagnostics showed maf low but within parameters but no other faults to point a finger at.


996TT_STEVO said:
Stop Oiling it, when I run my K&N 3/4 years ago, I had similar issues when oiling myself, you want to just use the pre-oiled version from new and don't oil again and you will be good!

I'm still putting money on it that your blowing them due to the power hike, did you blow them in hotter weather also?. I'm running 570/580ish and I blew 2 in summer, 1 South France and other at SPA.
On most occasions a completely blown MAF will show an ABS/PSM Warning light when completely blown, so I would look at cleaning or replacing the MAF. You want to use something like IPA to spray it with so there is no film/residue left over. Good Luck!
I doubt washing it in bitter will do the job...!

996TT_STEVO

4,078 posts

259 months

Monday 12th November 2007
quotequote all
Vesuvius 996 said:
996TT_STEVO said:
drhildr said:
I'll give this a go - what about after cleaning?

Hard to say when it went - became very evident yesteday at Vmax - down by 20mph on normal. Diagnostics showed maf low but within parameters but no other faults to point a finger at.


996TT_STEVO said:
Stop Oiling it, when I run my K&N 3/4 years ago, I had similar issues when oiling myself, you want to just use the pre-oiled version from new and don't oil again and you will be good!

I'm still putting money on it that your blowing them due to the power hike, did you blow them in hotter weather also?. I'm running 570/580ish and I blew 2 in summer, 1 South France and other at SPA.
On most occasions a completely blown MAF will show an ABS/PSM Warning light when completely blown, so I would look at cleaning or replacing the MAF. You want to use something like IPA to spray it with so there is no film/residue left over. Good Luck!
I doubt washing it in bitter will do the job...!
lol, now that's a good one! lol

drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all

I could of put rocket fuel in her and it wouldn't go a inch faster frown

Sorry we didn't get to mix it Mark - another time!

markbe said:
drhildr said:
How long do these things last in general - it looks like I've done 2 in 12 months! Is there any way of preserving the poor things or at least buying them cheap in bulk!!?
Now come on Dave; change back to a petrol derivative from your current methanol mix and all will be fine.hehe

Markbiggrin

Edited by markbe on Monday 12th November 12:10

markbe

1,755 posts

257 months

Monday 12th November 2007
quotequote all
drhildr said:
I could of put rocket fuel in her and it wouldn't go a inch faster frown

Sorry we didn't get to mix it Mark - another time!

Yes cheers Dave, next time might just be with a different car.

Mark.

markbe said:
drhildr said:
How long do these things last in general - it looks like I've done 2 in 12 months! Is there any way of preserving the poor things or at least buying them cheap in bulk!!?
Now come on Dave; change back to a petrol derivative from your current methanol mix and all will be fine.hehe

Markbiggrin

Edited by markbe on Monday 12th November 12:10

anonymous-user

85 months

Monday 12th November 2007
quotequote all
David,
I can 2nd the oilding issue as it true , happens all the time, try this then go from there.

Paul

cableguy

2,287 posts

240 months

Monday 12th November 2007
quotequote all
From experience the simplest way of eliminating MAF oil fouling problems is to oil the filter according to manufacturers instructions and then leave overnight face down on newspaper/blotting paper, this reduces any excess oil on the filter resulting in less fouling.

I used this method on my previous e39 M5 which resulted in OEM flow figures throughout the 12 months or so that the K&N Filters were fitted, many others users at the time just used to oil without blotting resulting in considerably less flow and fouling problems.

HTH.

C.


drhildr

Original Poster:

453 posts

257 months

Monday 12th November 2007
quotequote all
Anybody know a good source of filters - BMC 195/01


Paul_D_996RS said:
David,
I can 2nd the oilding issue as it true , happens all the time, try this then go from there.

Paul