996 Safety Roll Bars
996 Safety Roll Bars
Author
Discussion

David Hype

Original Poster:

2,296 posts

283 months

Monday 12th November 2007
quotequote all
I am thinking about getting a half cage for my GT3 Mk2, I want a Genuine Porsche Tequipment one, but they are way too pricey from Porsche directly (at over a grand)

I`ve seen one on www.carnewal.com which is circa £700, but it like much of Gerts stuff tends to be for LHD cars.

Are roll cages handed? This one has the diagonal bar going from bottom right to top right (when viewed from the front) suggesting more protection for a driver sitting on the left.

Are all Genuine Porsche cages for 996 coupes, GT3`s, Turbos and GT2`s the same?

Can anyone share some thoughts or advise on this please?

PetrolTed

34,468 posts

334 months

Monday 12th November 2007
quotequote all
OE cages are symmetrical I believe.

David Hype

Original Poster:

2,296 posts

283 months

Monday 12th November 2007
quotequote all
PetrolTed said:
OE cages are symmetrical I believe.
Thanks Ted, by which I assume that you mean that they are all the same regardless of on which side that you sit to drive?

G T 3

2,142 posts

285 months

Monday 12th November 2007
quotequote all
You better not race that car...........!

PetrolTed

34,468 posts

334 months

Monday 12th November 2007
quotequote all
David Hype said:
PetrolTed said:
OE cages are symmetrical I believe.
Thanks Ted, by which I assume that you mean that they are all the same regardless of on which side that you sit to drive?
I meant that the design is literally symmetrical. Certainly is in my GT3. That's the limited extent of my knowledge though.

thegoose

8,077 posts

241 months

Monday 12th November 2007
quotequote all
The specialist I use for my race car removed (for convenience) the front part of his colleague's Techquipment cage (2004 GT3) and was appalled at the quality (from a safety point of view) of it so I would recommend something else.

Try them if you want one www.uniteleven.co.uk Not something they'll stock but will be able to get you a price and fit it properly (latest technician is a GT3 expert fresh from Tech 9).

lightweight

1,165 posts

279 months

Tuesday 13th November 2007
quotequote all
Parr supplied and fitted a genuine techequipment cage in my car and the job they did was first rate it, can only be described as factory standard talk to Ted down there he is increadably helpfull and knows his stuff (used to spanner Panoz at le mans).The cost fitted was less than you mentioned though I have had a lot of other work done.

Re the original question yes the diagonal does go high left to low right on mine I would be supprised to see a RHD version as they sell so few i think the choice for you is Panamaracana(unbraced)or techequipment rear only(what i have) or full clubsport but for this if you fit the front section you will need to cut the carpets.

Edited by lightweight on Tuesday 13th November 09:10


Edited by lightweight on Tuesday 13th November 09:11

David Hype

Original Poster:

2,296 posts

283 months

Tuesday 13th November 2007
quotequote all
G T 3 said:
You better not race that car...........!
Don`t worry P no intention of racing it, just looking at options at the moment, how is the new toy?

G T 3

2,142 posts

285 months

Tuesday 13th November 2007
quotequote all
Should get it this week, bit of a delay...you about for the sunday meet this weekend...Bring the Tourag!!!!!

DanH

12,287 posts

291 months

Tuesday 13th November 2007
quotequote all
PetrolTed said:
OE cages are symmetrical I believe.
The one in RSs is as it has extra braces. Standard tequipment one isn't.

David Hype

Original Poster:

2,296 posts

283 months

Wednesday 14th November 2007
quotequote all
G T 3 said:
Should get it this week, bit of a delay...you about for the sunday meet this weekend...Bring the Tourag!!!!!
Why are you looking for a tow? laugh