MAF Sensor - how do I know if it's broken?
Discussion
I think my 996 Turbo is a bit down on power since when I first got it (May)
I've read that the mysterious MAF sensor is often a component that robs power when it's broken but how can I tell? Everything runs just fine and I've not tweaked or touched anything - it just doesnt feel like it launches into the horizon like it used to.
Or, maybe I've got used to the power. I hope not, not this early one, this could get expensive! Actually - I'd be surprised as it's only a weekend car so it's still a novelty driving it.
Can an OPC do a simple test to check for me? (It's under warranty)
I've read that the mysterious MAF sensor is often a component that robs power when it's broken but how can I tell? Everything runs just fine and I've not tweaked or touched anything - it just doesnt feel like it launches into the horizon like it used to.
Or, maybe I've got used to the power. I hope not, not this early one, this could get expensive! Actually - I'd be surprised as it's only a weekend car so it's still a novelty driving it.
Can an OPC do a simple test to check for me? (It's under warranty)
Hopefully the OPC can test it but my understanding (and experience) is that they go out of spec over time but don't actually go out far enough for the OBD to diagnose a fault. I found BMW very reluctant to change the ones off my M5 because they weren't technically broken. When they did replace them, the car was utterly transformed.
Maybe Porsche will be better, but there is a test that a local Bosch specialist had developed using an oscilliscope to look at some snap throttle opening thing, which I used to pursuade BMW that they'd gone. Clive Atthowe in Norwich, FWIW
Good luck and keep us posted.
SM
Maybe Porsche will be better, but there is a test that a local Bosch specialist had developed using an oscilliscope to look at some snap throttle opening thing, which I used to pursuade BMW that they'd gone. Clive Atthowe in Norwich, FWIW
Good luck and keep us posted.
SM
Before you waste time and potentially money on the MAF sensor just check you have decent fuel in the car, pal of mine with a turbo had it Manthey'd to 520bhp and loved it then suddenly it seems that little bit extra had gone almost like the turbo pipe coming off.
After speaking with JZM it was diagnosed as bad fuel, fill up with sooperdooper or whatever they call it and car was transformed again, not sure if this only affects chipped cars or all cars but maybe worth trying if you filled up somewhere that you are unsure of ....
Also as a side note, when fitting the cup filter to a std 996 C2 I tried it briefly without the sensor and couldnt see any difference in performance.
Regards
After speaking with JZM it was diagnosed as bad fuel, fill up with sooperdooper or whatever they call it and car was transformed again, not sure if this only affects chipped cars or all cars but maybe worth trying if you filled up somewhere that you are unsure of ....
Also as a side note, when fitting the cup filter to a std 996 C2 I tried it briefly without the sensor and couldnt see any difference in performance.
Regards
I had a MAF sensor go on 996 C2
The symptoms are as follows
When accelerating through the rev range (2nds best the best gear to try) the engine will stutter around the 3.5K onwards mark and be slower towards the red-line, while not feeling very smooth either. You’ll be able to feel it no problem.
OPC can plug it in and find it in minutes
Good luck
The symptoms are as follows
When accelerating through the rev range (2nds best the best gear to try) the engine will stutter around the 3.5K onwards mark and be slower towards the red-line, while not feeling very smooth either. You’ll be able to feel it no problem.
OPC can plug it in and find it in minutes
Good luck
Does this stutter happen all the time, or with just partial throttle opening? With full throttle I never see anything, but sometimes I feel a short loss of power at about 5800 rpm if not floored.
Otherwise, all seems well. Seems smooth otherwise, but I never feel like it really wants to take off at high revs like I would expect.
I read that it's easy to change the MAF (5 mins). Is this realistic? Are there any pitfalls to the DIY option (potential to destroy something expensive)?
Mines a 3.4 C2.
Otherwise, all seems well. Seems smooth otherwise, but I never feel like it really wants to take off at high revs like I would expect.
I read that it's easy to change the MAF (5 mins). Is this realistic? Are there any pitfalls to the DIY option (potential to destroy something expensive)?
Mines a 3.4 C2.
clubsport said:
You can unplug the electrical plug to the maf on most cars, if the car runs the same with this disconnected, then chances are the maf isn't doing much and needs replacing.
Ignore this post, if you unplug it, it splutters and runs funny it could be seriously knackered and the same would happen when a new one is fitted if the old is faulty.Your OPC can see if its working with the PIWIS checking the actual values.
Quite often on Turbo's if the MAF is faulty when driven hard the PSM/ABS lights will flash on, this is due to a torque disturbance issue caused by the MAF sensor
BlueC2 said:
Does this stutter happen all the time, or with just partial throttle opening? With full throttle I never see anything, but sometimes I feel a short loss of power at about 5800 rpm if not floored.
Otherwise, all seems well. Seems smooth otherwise, but I never feel like it really wants to take off at high revs like I would expect.
I read that it's easy to change the MAF (5 mins). Is this realistic? Are there any pitfalls to the DIY option (potential to destroy something expensive)?
Mines a 3.4 C2.
DIY is VERY easy. Buy the ne MAF from Eurocarparts. Buy a torx bit set. Job done.Otherwise, all seems well. Seems smooth otherwise, but I never feel like it really wants to take off at high revs like I would expect.
I read that it's easy to change the MAF (5 mins). Is this realistic? Are there any pitfalls to the DIY option (potential to destroy something expensive)?
Mines a 3.4 C2.
BlueC2 said:
Does this stutter happen all the time, or with just partial throttle opening? With full throttle I never see anything, but sometimes I feel a short loss of power at about 5800 rpm if not floored.
Otherwise, all seems well. Seems smooth otherwise, but I never feel like it really wants to take off at high revs like I would expect.
I read that it's easy to change the MAF (5 mins). Is this realistic? Are there any pitfalls to the DIY option (potential to destroy something expensive)?
Mines a 3.4 C2.
If you’re not used to the feeling the engine at high revs you might not be able to tell I suppose. 5800 is where I felt a loss of power and lack of smoothness the most. Get the car checked out properly before you buy anything or change parts. If you’re in the north I'll quite happily drive the wheels off it and diagnose a knacked MAF. It's fairly common fault apparentlyOtherwise, all seems well. Seems smooth otherwise, but I never feel like it really wants to take off at high revs like I would expect.
I read that it's easy to change the MAF (5 mins). Is this realistic? Are there any pitfalls to the DIY option (potential to destroy something expensive)?
Mines a 3.4 C2.
I had a 3.4 C2 also btw
When its in being checked, get them to check the wastegate actuators / levers we have been receiving an increasing amount of cars with seized spindles on the turbos - they go very well for a while (stuck shut so boost is(too)high) then pressure blows the wastegate valve open whereupon it sticks and leaves you with one turbo doing the job of two. Not scaremongering but have seen it about ten times this year.
Gassing Station | Porsche General | Top of Page | What's New | My Stuff


