Any Advise when fitting a Tequipment roll over bar !!
Discussion
LOL... Dan, the bottom 2 feet of the cage can be a bit tight across the width of the inside of the car. It needs to be tilted back into position - be careful around the base feet and the carpet. You need to cut 2 small holes in the carpet for the rear legs to bolt to the where the rear seatbelt mounting points are.
Finished installing mine yesterday....not the simplest job, the biggest gotcha is the risk of cross threading the UNF bolts that mount the 4 arms.
Best to email me and I'll send you the step-by-step I downloaded, along with a PDF of a RennList thread that adds a lot of useful info. More than willing to chat it over on the phone, prob quicker than typing it!
First piece of advice would be to trot off to Machine Mart and buy 2 x ratchet straps (light duty is morer than adequate) for about £10...use them for gently squeezing together the rear arms and front legs to afford some manoeverability of the cage, you'll struggle otherwise.
Most of the time is in the prep work, removing trim and cutting a "rocker panel" that sits inderneath the carpet just inside the door sills...dont try and do it quickly, too big a risk of damage.
Total time spent, across 3 days and interrupted by rain, was about 12hrs...being ultra careful and having to take some rear trim back out to run a tap thro one of the rear mounting holes.
Best to email me and I'll send you the step-by-step I downloaded, along with a PDF of a RennList thread that adds a lot of useful info. More than willing to chat it over on the phone, prob quicker than typing it!
First piece of advice would be to trot off to Machine Mart and buy 2 x ratchet straps (light duty is morer than adequate) for about £10...use them for gently squeezing together the rear arms and front legs to afford some manoeverability of the cage, you'll struggle otherwise.
Most of the time is in the prep work, removing trim and cutting a "rocker panel" that sits inderneath the carpet just inside the door sills...dont try and do it quickly, too big a risk of damage.
Total time spent, across 3 days and interrupted by rain, was about 12hrs...being ultra careful and having to take some rear trim back out to run a tap thro one of the rear mounting holes.
spenny_b said:
Finished installing mine yesterday....not the simplest job, the biggest gotcha is the risk of cross threading the UNF bolts that mount the 4 arms.
Best to email me and I'll send you the step-by-step I downloaded, along with a PDF of a RennList thread that adds a lot of useful info. More than willing to chat it over on the phone, prob quicker than typing it!
First piece of advice would be to trot off to Machine Mart and buy 2 x ratchet straps (light duty is morer than adequate) for about £10...use them for gently squeezing together the rear arms and front legs to afford some manoeverability of the cage, you'll struggle otherwise.
Most of the time is in the prep work, removing trim and cutting a "rocker panel" that sits inderneath the carpet just inside the door sills...dont try and do it quickly, too big a risk of damage.
Total time spent, across 3 days and interrupted by rain, was about 12hrs...being ultra careful and having to take some rear trim back out to run a tap thro one of the rear mounting holes.
spenny_b, I would be very interested in the step-by-step guideBest to email me and I'll send you the step-by-step I downloaded, along with a PDF of a RennList thread that adds a lot of useful info. More than willing to chat it over on the phone, prob quicker than typing it!
First piece of advice would be to trot off to Machine Mart and buy 2 x ratchet straps (light duty is morer than adequate) for about £10...use them for gently squeezing together the rear arms and front legs to afford some manoeverability of the cage, you'll struggle otherwise.
Most of the time is in the prep work, removing trim and cutting a "rocker panel" that sits inderneath the carpet just inside the door sills...dont try and do it quickly, too big a risk of damage.
Total time spent, across 3 days and interrupted by rain, was about 12hrs...being ultra careful and having to take some rear trim back out to run a tap thro one of the rear mounting holes.
if you could email it to me via my profile...
Edited by David Hype on Wednesday 14th November 12:18
Slippydiff said:
7357 said:
12 Hours !!!!! 
When fitting yours was it you alone ? and was the car on a ramp ?
I have booked a 2.5 hours slot, with two of us doing it !
Best you order a replacement headlining and other sundry trim items now then !
When fitting yours was it you alone ? and was the car on a ramp ?
I have booked a 2.5 hours slot, with two of us doing it !

If I have not booked enough time I can sort this out..
7357 said:
12 Hours !!!!!
When fitting yours was it you alone ? and was the car on a ramp ?
I have booked a 2.5 hours slot, with two of us doing it !
Yup, mostly installed single-handed. My Brother spared me 15mins to help get the cage into the car (obv with seats removed, along with coat hangers & seat belt mounting covers). This turned out to be very easy so long as you dont skimp on prep work.When fitting yours was it you alone ? and was the car on a ramp ?
I have booked a 2.5 hours slot, with two of us doing it !
Some of the US guys have tried to do this without cutting the rocker panel inside the sill (covered in carpet)...DON'T!!...you'll end up crushing it with the front legs, maybe splintering it...there are wires v nearby. You also wont be able to shuffle the cage around to insert bolts.
Like I said, most of the time is spent prepping for everything.
Don't forget, some of my time was spent packing/unpacking each time it threw it down and each evening, gulping cups of tea whilst warming fingers(!) and trying in vain to work with inspection lamps when the light went, and so on.
You dont need ramps, but 2.5hrs, I suggest, will be far too little unless your tech has done 1 or 2 before....don't rush it, it's very easy to either scratch something or tear a headlining as Slippy says. I have heard horror stories of cracked front windscreens, which I have to say, I think you'd have to be pretty brutal to do that! Certainly the rear view mirror needs massaging to allow the top hoop past.
David...I'll email you what I have...
spenny_b said:
7357 said:
12 Hours !!!!!
When fitting yours was it you alone ? and was the car on a ramp ?
I have booked a 2.5 hours slot, with two of us doing it !
Yup, mostly installed single-handed. My Brother spared me 15mins to help get the cage into the car (obv with seats removed, along with coat hangers & seat belt mounting covers). This turned out to be very easy so long as you dont skimp on prep work.When fitting yours was it you alone ? and was the car on a ramp ?
I have booked a 2.5 hours slot, with two of us doing it !
Some of the US guys have tried to do this without cutting the rocker panel inside the sill (covered in carpet)...DON'T!!...you'll end up crushing it with the front legs, maybe splintering it...there are wires v nearby. You also wont be able to shuffle the cage around to insert bolts.
Like I said, most of the time is spent prepping for everything.
Don't forget, some of my time was spent packing/unpacking each time it threw it down and each evening, gulping cups of tea whilst warming fingers(!) and trying in vain to work with inspection lamps when the light went, and so on.
You dont need ramps, but 2.5hrs, I suggest, will be far too little unless your tech has done 1 or 2 before....don't rush it, it's very easy to either scratch something or tear a headlining as Slippy says. I have heard horror stories of cracked front windscreens, which I have to say, I think you'd have to be pretty brutal to do that! Certainly the rear view mirror needs massaging to allow the top hoop past.
David...I'll email you what I have...
7357 said:
7357 said:
I understand the rear mounts fit into where the seat belt brackets would be.. but what of the front mounts ?
So before I start.. What do I need to remove ??
The front mounts to where the front seatbelt would mount to if not attched to your (presumably) bucket seats.I understand the rear mounts fit into where the seat belt brackets would be.. but what of the front mounts ?
So before I start.. What do I need to remove ??
Look down the inside of the door sill, under the setabelt assy, and you'll see a plastic cap covering a 7/16" bolt...you remove this and the spacer and use the supplied UNF bolt that comes with cage.
Send me that email and I'll send you "my thoughts" that I've just typed up for David, along with pics/PDF docs
spenny_b said:
7357 said:
7357 said:
I understand the rear mounts fit into where the seat belt brackets would be.. but what of the front mounts ?
So before I start.. What do I need to remove ??
The front mounts to where the front seatbelt would mount to if not attched to your (presumably) bucket seats.I understand the rear mounts fit into where the seat belt brackets would be.. but what of the front mounts ?
So before I start.. What do I need to remove ??
Look down the inside of the door sill, under the setabelt assy, and you'll see a plastic cap covering a 7/16" bolt...you remove this and the spacer and use the supplied UNF bolt that comes with cage.
Send me that email and I'll send you "my thoughts" that I've just typed up for David, along with pics/PDF docs
spenny_b said:
Send me that email and I'll send you "my thoughts" that I've just typed up for David, along with pics/PDF docs
Thanks mate.. I think I still have your email address from when you were looking to buy a MK1.So will send you one when I get home.Thanks
Dan
Edited by 7357 on Wednesday 14th November 16:34
spenny_b said:
Dan said:
Thanks mate.. I think I still have your email address from when you were looking to buy a MK1.So will send you one when I get home.
Thanks
Dan
Sorry Dan, me having a thick-wednesday moment...email on its way to you now! Thanks
Dan

Thanks again
Gassing Station | Porsche General | Top of Page | What's New | My Stuff


