"sizing" bolts!
Discussion
I'm crap at sizing threads, so I always keep old bolts for use and reference, plus I purchased a variety of these reasonably priced silverline bolt and fastening kits for off the shelf help.
http://shop.comdir.co.uk/Products.aspx?intGroupID=...
http://shop.comdir.co.uk/Products.aspx?intGroupID=...
NiceCupOfTea said:
Hi, just acquired an airbox for my MX5 to replace the cone filter but it's missing a few bolts. I have one or two and need to buy some more.
How can I ID what size/thread/head size they are by looking at them?
For metric threads you need to accurately measure the diameter of the threeaded part, and the length of the bolt. How can I ID what size/thread/head size they are by looking at them?
You may find you have some oddball 'pitches' too, which is the distance between the threads, maybe 1mm, or 1.25 or thereabouts.
Best way is to simply find one that screw in the hole and is a good fit, not waggling about, find out the length you need, and take it to the parts shop and get a similar one.
NiceCupOfTea said:
How can I ID what size/thread/head size they are by looking at them?
Measure the outside diameter of the thread to see whether they are an exact number of mm or an exact number of 32ndths of an inch. Count the number of turns of thread and the length of the thread (the longer length you can do this over the better) to see whether the thread pitch is an exact number of turns per inch, or a round number in mm (1.0mm, 1.25mm, 1.5mm are the common sizes) or something else.Check whether they are threaded along their entire length (indicating they are machine screws) or have an unthreaded section (called the 'grip') indicating they are bolts.
Go to any local fastener supplier, take the bolt/screw, tell them what the measurements are and ask them to natch it, or go to any of the online suppliers and look for the matching part. For an unstressed component you can use any material you like (perhaps best to avoid plastic or aluminium though if you're offered the choice!).
Don't assume all the bolts/screws will be the same - test fit the ones you have in all the holes to make sure they screw right in and have at least 1.5x bolt diameter of engagement.
Edited by GreenV8S on Saturday 12th July 15:27
NiceCupOfTea said:
Hi, just acquired an airbox for my MX5 to replace the cone filter but it's missing a few bolts. I have one or two and need to buy some more.
How can I ID what size/thread/head size they are by looking at them?
Ring the dealer, ask him the size. Then go and buy some from your local fastener supplier.How can I ID what size/thread/head size they are by looking at them?
NiceCupOfTea said:
miniman said:
How soon do you need them? I've just ordered a filtercharger kit from MX5parts so when I fit it I will have the airbox bits left over!
Not desperately soon - have the cone filter still on the car at the mo!As far as I can see without fitting it, there are 4 or 5 big bolts with captive washers needed to bolt the airbox / pipes to the car, I am missing 2 or 3.
There are also some threaded dowels with some nuts that I assume are to bolt the airbox onto the AMM but I am short of the nuts!
Does that make sense?
Without trying to fit it I don't know any more (and given it's the only working car of 3 at the moment I am loath to tinker until the others are running!)
There are also some threaded dowels with some nuts that I assume are to bolt the airbox onto the AMM but I am short of the nuts!
Does that make sense?
Without trying to fit it I don't know any more (and given it's the only working car of 3 at the moment I am loath to tinker until the others are running!)
Gassing Station | The Pie & Piston Archive | Top of Page | What's New | My Stuff





