Lock problems - please help!
Discussion
I removed the Yale lock from the front door the other day for painting. When I got back yesterday I had some troubles getting the door open but I eventually worked out I needed to jiggle the key a little.
Today I get back from work and find I cannot open the door at all. The key simply will not turn. Eventually I have to break in and check the lock to see what is going on. The weird bit is that the key works like a charm when the door is open, but as soon as it closes, it will not turn.
The lock has 2 'catches' (the bits that stick out and keep the door closed). There is a large one that is obviously keeping the door closed, and then there is a much smaller one below it. I found that this smaller one does not drop into the recess on the other side of the door when it is closed. I assume this is on purpose so the lock knows if the door is open or closed. However, when the smaller catch is depressed, the key will no longer turn in the lock (although the handle on the inside will still operate).
Please can someone explain what is going on? Should the small catch fit into the recess? Have I managed to put the lock into some strange mode that only allows the inside handle to operate?
Today I get back from work and find I cannot open the door at all. The key simply will not turn. Eventually I have to break in and check the lock to see what is going on. The weird bit is that the key works like a charm when the door is open, but as soon as it closes, it will not turn.
The lock has 2 'catches' (the bits that stick out and keep the door closed). There is a large one that is obviously keeping the door closed, and then there is a much smaller one below it. I found that this smaller one does not drop into the recess on the other side of the door when it is closed. I assume this is on purpose so the lock knows if the door is open or closed. However, when the smaller catch is depressed, the key will no longer turn in the lock (although the handle on the inside will still operate).
Please can someone explain what is going on? Should the small catch fit into the recess? Have I managed to put the lock into some strange mode that only allows the inside handle to operate?
The small catch does not go in the recess.When this catch is pushed in by the latch plate, it works the deadlock mechanism. This means when the small one is pressed in, the large one cant be pushed in,so to stop it being opened by means of a credit card (did anyone ever actually do this?)or a blade/knife etc.
As for it sticking, does the key turn the barrel with the lock itself(the part on the inside of the door)off? If not, then replace the barrel, not expensive.If this turns check the small flat bar that locates these two lock parts is slotted in at the right angle.
Good Luck
As for it sticking, does the key turn the barrel with the lock itself(the part on the inside of the door)off? If not, then replace the barrel, not expensive.If this turns check the small flat bar that locates these two lock parts is slotted in at the right angle.
Good Luck
mgtony said:
The small catch does not go in the recess.When this catch is pushed in by the latch plate, it works the deadlock mechanism. This means when the small one is pressed in, the large one cant be pushed in,so to stop it being opened by means of a credit card (did anyone ever actually do this?)or a blade/knife etc.
As for it sticking, does the key turn the barrel with the lock itself(the part on the inside of the door)off? If not, then replace the barrel, not expensive.If this turns check the small flat bar that locates these two lock parts is slotted in at the right angle.
Good Luck
They key turns just fine when the door is open and it retracts the main catch and the smaller catch. It also turns ok when the lock is removed from the door. As soon as the door is closed the key no longer turns in the lock. Pretty sure the barrel is ok so I will check the bar again. I remember there are some arrows you need to align when fitting it which I am pretty sure I did but I will check again. Many thanks for your advice.As for it sticking, does the key turn the barrel with the lock itself(the part on the inside of the door)off? If not, then replace the barrel, not expensive.If this turns check the small flat bar that locates these two lock parts is slotted in at the right angle.
Good Luck
With the door open, if you push the small catch in with your thumb, does the key still turn to open the large catch? if it does, then lock should be ok. The large catch could be jamming on the top,bottom or rear of the catch plate on the frame, although this would also make it difficult to open from the inside.
mgtony said:
With the door open, if you push the small catch in with your thumb, does the key still turn to open the large catch? if it does, then lock should be ok. The large catch could be jamming on the top,bottom or rear of the catch plate on the frame, although this would also make it difficult to open from the inside.
No. If you push the small catch in, the key will not turn in the lock.marctwo said:
mgtony said:
With the door open, if you push the small catch in with your thumb, does the key still turn to open the large catch? if it does, then lock should be ok. The large catch could be jamming on the top,bottom or rear of the catch plate on the frame, although this would also make it difficult to open from the inside.
No. If you push the small catch in, the key will not turn in the lock.Edited by illmonkey on Thursday 24th July 08:28
marctwo said:
mgtony said:
With the door open, if you push the small catch in with your thumb, does the key still turn to open the large catch? if it does, then lock should be ok. The large catch could be jamming on the top,bottom or rear of the catch plate on the frame, although this would also make it difficult to open from the inside.
No. If you push the small catch in, the key will not turn in the lock.HTH
jesta1865 said:
i am no expert, but that sounds to me like the small catch is not clearing into space when the door is closed, perhaps you need to look at the door jam and see if the recess needs to be moved (if metal etc) or made slightly larger if straight into the wood.
HTH
HTH
mgtony said:
The small catch does not go in the recess.
So which is it? If the small catch is supposed to drop into the recess then it should work ok but, as mgtony says, it is not supposed to as this is how it prevents the lock being opened by sliding a card into the gap. It looks to me that it never did go into the recess so I shall disassemble the whole thing tonight and try to make sure it is all correctly alligned.
Thanks to you all for your suggestions but I finally worked it out. I had put a new cylinder pull on the outside of the door which was thinner than the one I had removed. This meant that the flat 'plate' that links the cylinder to the rest of the lock on the inside of the door was now longer than it needed to be. For some reason this caused the behaviour I described. I simply loosened the screws that connected the lock to the cylinder and it worked as normal. Very very strange!
Gassing Station | The Pie & Piston Archive | Top of Page | What's New | My Stuff





