Uneven Idle & Fouled Plugs
Discussion
Done about 300 miles on the GPZ after giving it some new plugs, filters, oil, fluids etc and it seems to be running surprisingly well with just a couple of issues: The old plugs were black, indicating that it's been running rich, and the idle is a bit variable until it's in the middle of the temperature guage. I've bunged half a bottle of Redex through it and it still seems the same, any pointers? I've very little experience of playing with carbs and the like (and have forgotten most of what I did know) - it's at least a decade since I looked at an engine that wasn't fuel injected 
Cheers chaps

Cheers chaps

StevRS said:
Standard Kwak dry one - hopefully it's not oiled at all 
Ah, my old zxr had an oiled one. When I read it I thought you'd introduced the problem with the service but now I read it again it sounds like it existed before. Were the plugs oily at all or just carbonised? I'm afraid I can't remember any of my carb related stuff (and I didn't know that much to begin with) 

The old plugs were carbonised, not oily. It's defo running rich (or was before I did the change). The problem may just be odds & sods of old fuel and redex running amok round the fuel system (I watered down the old fuel with new and put far too much redex in so I had to wind up the idle speed a fair bit until more fuel went in to water it down a bit!!) - I've filled him up after a 130 mile run to work & back yesterday and will see how he gets on...
12k miles approaches - how easy are valve clearances to check? I've got a Haynes manual - guess I'll have to get me spanners out again
12k miles approaches - how easy are valve clearances to check? I've got a Haynes manual - guess I'll have to get me spanners out again

StevRS said:
12k miles approaches - how easy are valve clearances to check? I've got a Haynes manual - guess I'll have to get me spanners out again 
I don't know what gpz you have but basically you need to get the rocker cover off and then turn the engine according to your owner's manual and then simply use a feeler gauge to measure the clearance between the valve shim bucket and the cam (assuming you have shims). 
If you don't have shims there may be some kind of adjustable rocker system but essentially to check them the procedure is very similar. You need the workshop manual for the clearances and the procedure (i.e. move engine to TDC and check inlet clearances on 1 and then rotate by 180 and that kind of thing). It's not difficult but you may have to remove some stuff to get to the valves and you'll need the procedure.
I've never had to adjust mine but if you have an adjustable system then it should be easy but if it's shims it could be a pain as essentially you need to measure the gap, work out the change you need, measure the thickness of the shim (after removing the cams) and then working out what shim you need. You build a list and order them in... I haven't had to do this yet but I imagine it's quite involved which is why it costs a bit of money. Obviously unless you have a big pile of shims kicking about then you'll have to order them in which would take a bit of time and then it's your choice as to whether or not to reassemble it all in the mean time.
Anyway, checking them is relatively easy and the chances are that they will be fine. Mine were the last time I checked mine at 35k and my check interval is 12k (I think). If you find that they're out you can then decide on whether to farm out the work but at least you'll have looked in to the bits you'll need to work on which will either give confidence or scare you s
tless 
The first time I did mine it took bloody ages but now is pretty quick. Even taking the cams/buckets/shims out really isn't hard if you're methodical - I have to take all mine out to get some machining done on the head after it spat a spark plug out.
Have fun,
Mark
if the carbs are like the only jap carbs i've played with. try screwing the air bleed screw right the way out and resetting it. if your lucky the screws even come right out to clean.
the carbs i had, undoing the screw allowed more air in to make it leaner. mine was rich & it seemed to be only at lower revs. fiddling with the air bleed screws seemed to help. my guess was they'd blocked up with goo where it'd stood before i got it.
the carbs i had, undoing the screw allowed more air in to make it leaner. mine was rich & it seemed to be only at lower revs. fiddling with the air bleed screws seemed to help. my guess was they'd blocked up with goo where it'd stood before i got it.
a smell of fuel? sticky floats maybe then?
have you stripped the carbs down, or just dosed them with redex? its got to be worth taking the float bowls off at least to check if they are full of goo. petrol seems to turn to snot if you leave it long enough & it doesnt take much snot to block things or make bits sticky.
oddly enough ive got a mate with a GPZ500 in her garden, it runs but at low revs pours fuel down the engine so it could be the same problem.
have you stripped the carbs down, or just dosed them with redex? its got to be worth taking the float bowls off at least to check if they are full of goo. petrol seems to turn to snot if you leave it long enough & it doesnt take much snot to block things or make bits sticky.
oddly enough ive got a mate with a GPZ500 in her garden, it runs but at low revs pours fuel down the engine so it could be the same problem.
Past experience says drop the float bowls, take the air screws out, and clean everything before resetting everything to nominal, old jap carbs bung up really easily.
I remember the carbs on a GPX600 (1980's vintage) did this to me and we ended op taking the whole set of four off to clean them out, took nearly a day to refit the buggers again, no room to get at anything.
Check the carb balance as well (or get someone to do it for you), often the cause of poor running.
Hate the job so good luck.
I remember the carbs on a GPX600 (1980's vintage) did this to me and we ended op taking the whole set of four off to clean them out, took nearly a day to refit the buggers again, no room to get at anything.
Check the carb balance as well (or get someone to do it for you), often the cause of poor running.
Hate the job so good luck.
paul_tim2000 said:
Check the carb balance as well (or get someone to do it for you), often the cause of poor running.
quick n easy way to approximate this is - use a small drill bit between the venturi & the butterfly on each carb to check the gap is the same.it wont get the balance perfect but it should get it good enough to run ok.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff



