Discussion
My bargain CBR600F, which was otherwise very clean with a full service history, is missing the throttle bar end. I think that's why the clutch grip vibrates at certain speeds, which gives me a zizzy hand eventually.
Now I could just buy one OEM Honda bar end and be done with it, however looking on my local bike shop's website, there are fancy carbon bar ends, anodised ally bar ends, bar end protectors, etc.
What's the general consensus on aftermarket bar ends? I'm no racer, and the bike is currently completely standard and well maintained. The previous owner did 50k miles on it, so the ally bar end left is a bit corroded and tatty, and the only non-standard parts he put on it are a carbon fibre hugger, a Scottoiler and a 'carbon effect' sticker on the steering fork head plate (?). Oh yeah, and a carbon look tank protector.
So, given the bike is very clean and standard-looking, but has a couple of carbon bits, I'm thinking a set of carbon bar ends may stop the zizzy left bar, without looking like I'm blinging up the bike too much. I don't want to turn the bike into a dog's dinner, nor do I want it attractive to thieves (I park outside).
Will the carbon bar ends do the job? I'm assuming the general purpose is to add weight to reduce the resonant frequency of the bars... so light weight (i.e. carbon fibre) will be purely for show, as some mass is required!!! The other alternative is bright anodised ally, which may attract attention.
Is there any performance difference (i.e. do some bar ends work better than others at reducing vibration), or is it just cosmetic, and I should go with what I like the look of?
Now I could just buy one OEM Honda bar end and be done with it, however looking on my local bike shop's website, there are fancy carbon bar ends, anodised ally bar ends, bar end protectors, etc.
What's the general consensus on aftermarket bar ends? I'm no racer, and the bike is currently completely standard and well maintained. The previous owner did 50k miles on it, so the ally bar end left is a bit corroded and tatty, and the only non-standard parts he put on it are a carbon fibre hugger, a Scottoiler and a 'carbon effect' sticker on the steering fork head plate (?). Oh yeah, and a carbon look tank protector.
So, given the bike is very clean and standard-looking, but has a couple of carbon bits, I'm thinking a set of carbon bar ends may stop the zizzy left bar, without looking like I'm blinging up the bike too much. I don't want to turn the bike into a dog's dinner, nor do I want it attractive to thieves (I park outside).
Will the carbon bar ends do the job? I'm assuming the general purpose is to add weight to reduce the resonant frequency of the bars... so light weight (i.e. carbon fibre) will be purely for show, as some mass is required!!! The other alternative is bright anodised ally, which may attract attention.
Is there any performance difference (i.e. do some bar ends work better than others at reducing vibration), or is it just cosmetic, and I should go with what I like the look of?
I added R&G bar ends to the Gixxer as they look kewl, IMO, and, yes, they do seem to reduce vibration slightly...
Not too sure if that's me justifying to myself or not tho'! But I'm very happy with them... They're not too bling, look functional and racey (to my eye) and don't cost the earth.
Johnny
Not too sure if that's me justifying to myself or not tho'! But I'm very happy with them... They're not too bling, look functional and racey (to my eye) and don't cost the earth.
Johnny
Johnny said:
Stu R said:
should be punishable by death imo 
Very much so...
Or perhaps I'll order both blue and purple, and have different colours on each bar so I can remember which is the clutch and which is the brake. I've already painted L and R on the mirrors.

cyberface said:
Johnny said:
Stu R said:
should be punishable by death imo 
Very much so...
Or perhaps I'll order both blue and purple, and have different colours on each bar so I can remember which is the clutch and which is the brake. I've already painted L and R on the mirrors.

Biker's Nemesis said:
Bar end weights are designed to reduce vibration, and so stop your little fingers going numb.
Anodized bar end weights are seriously naff, OK if you're a shell suits wearing chav.
That's what I thought. Oddly the bar with the missing bar end is the throttle, and it's the other bar that turns my hand into numb jelly. And given my lame clutch control, it makes for interesting low-speed manoeuvring Anodized bar end weights are seriously naff, OK if you're a shell suits wearing chav.

Given that the only non-OEM ones on the market appear to be blingy anodised thingies, I think I'll get the black anodised bar ends, since they don't look much different than the OEM ones and will at least be matched.
Or would a single vibrating bar (opposite to the bar with the end weight) indicate a possible other problem? At £13 for two bar ends I may as well buy them, install them and see whether the vibes have gone.
At the moment, I'm having to ride one handed everywhere and spend most of the time veering into the opposite side of the road.

cyberface said:
Biker's Nemesis said:
Bar end weights are designed to reduce vibration, and so stop your little fingers going numb.
Anodized bar end weights are seriously naff, OK if you're a shell suits wearing chav.
That's what I thought. Oddly the bar with the missing bar end is the throttle, and it's the other bar that turns my hand into numb jelly. And given my lame clutch control, it makes for interesting low-speed manoeuvring Anodized bar end weights are seriously naff, OK if you're a shell suits wearing chav.

Given that the only non-OEM ones on the market appear to be blingy anodised thingies, I think I'll get the black anodised bar ends, since they don't look much different than the OEM ones and will at least be matched.
Or would a single vibrating bar (opposite to the bar with the end weight) indicate a possible other problem? At £13 for two bar ends I may as well buy them, install them and see whether the vibes have gone.
At the moment, I'm having to ride one handed everywhere and spend most of the time veering into the opposite side of the road.

I'd expect Honda would have a dam good reason for designing a bar end weight the way it is, although Albert in his industrial estate in the Midlands might dispute this and say that his anodised bar end weight turned on an Argus lathe is just the job.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff



te.

