Rough cost
Author
Discussion

J5MBF

Original Poster:

260 posts

231 months

Sunday 14th September 2008
quotequote all
How much a i looking at roughly to change chain and sprocket on my '99 R6? Is it difficult? and can you recommed a decent garage around the worcester (west mids) area? No more questions, i promise. Any help much appreciated. Cheers

Carl-H

947 posts

237 months

Sunday 14th September 2008
quotequote all
If you have a paddock stand its really easy to do yourself. Not sure on cost though. you could probably spend £60 or £300 if you wanted to.

Momentofmadness

2,371 posts

272 months

Sunday 14th September 2008
quotequote all
Have a look here, a decent garage shouldn't charge more than £30-40 for fitting.

http://www.bandcexpress.co.uk/cgi-bin/bc_page.pl?c...



dern

14,055 posts

310 months

Sunday 14th September 2008
quotequote all
It's not a job I'd recommend to anyone if they don't otherwise work on their bike to be honest.

I'd imagine a tyre type place would do it for £150 incl chain and sprockets.

RizzoTheRat

29,150 posts

223 months

Sunday 14th September 2008
quotequote all
Agreed, wouldn't reccomend trying it yourself unless you can get your hands on a dremmel or similar to cut the heads off the old link, and a chain riveting tool to put it back togehter. A decent garage should charge you under an hours labour to do it. £100-£150 for the chain and sprockets, genuine Yam will be more expensive (£45 compared to £12 for my front sprocket) and no better.

smack

9,777 posts

222 months

Sunday 14th September 2008
quotequote all
RizzoTheRat said:
Agreed, wouldn't reccomend trying it yourself unless you can get your hands on a dremmel or similar to cut the heads off the old link
Or a hacksaw and just hack through the old chain smile
RizzoTheRat said:
and a chain riveting tool to put it back togehter.
A must have for the job!

Busamav

2,954 posts

239 months

Sunday 14th September 2008
quotequote all
if you do go ahead and try it your self ( and i wouldnt recomend it either )

Do not remove the chain untill you have the engine sprocket loosened off

smack

9,777 posts

222 months

Monday 15th September 2008
quotequote all
Busamav said:
if you do go ahead and try it your self ( and i wouldnt recomend it either )

Do not remove the chain untill you have the engine sprocket loosened off
To do the job you will need:
Paddock stand
Hex / Alen keys
Screw drivers + and - ones
1/2 Drive socket set (with large sockets)
Possibly a bigger socket for wheel nut
Breaker Bar
Chain busting tool of your choice
Riveting tool
Big Hammer
Loctite
Torque wench

If your answer to anything on the list is "what's that", then take it to a shop. Or if your name is Chilli...

lawrence567

7,507 posts

221 months

Monday 15th September 2008
quotequote all
drive it into a bush?

dern

14,055 posts

310 months

Monday 15th September 2008
quotequote all
smack said:
RizzoTheRat said:
and a chain riveting tool to put it back togehter.
A must have for the job!
If you have a decent one then maybe but the standard diy ones are pretty st and an angle grinder will take your old chain off more efficiently and a ball pein hammer will mushroom the ends of the pins more convincingly. If you want one though you can fetch mine... it's covered in blood, an important (and weak) bit snapped off and embedded in the wall of my garage wink

RizzoTheRat

29,150 posts

223 months

Monday 15th September 2008
quotequote all
Trouble I had doing one with a ball pien was stopping it moving, managed to wedge a sledge hammer against the back of the chain in the end but it was still a pain in the backside. Borrowed a Whale chain rivting tool off a mate for the last one and it worked really well.

dern

14,055 posts

310 months

Monday 15th September 2008
quotequote all
RizzoTheRat said:
Trouble I had doing one with a ball pien was stopping it moving, managed to wedge a sledge hammer against the back of the chain in the end but it was still a pain in the backside. Borrowed a Whale chain rivting tool off a mate for the last one and it worked really well.
I have a lump hammer with flat sides which I use as an anvil.

Having just done a google that whale one looks pretty good. I bought the generic st motrax one to my cost.

Edited by dern on Monday 15th September 15:39

Venom

1,864 posts

290 months

Monday 15th September 2008
quotequote all
I borrowed a friend's Motrax to do mine. Just about avoided the need for a skin graft afterwards!

smack

9,777 posts

222 months

Monday 15th September 2008
quotequote all
I have the Whale tool, it has been a good to me so far, and nice and solid. Didn't really work for pin extraction, as all my bashing energy wasn't going into the pin with the chain flexing. I could have messed around with something hard/heaving behind the chain - but a hacksaw was the nearest thing to hand.
An angle grinder will be noisy, slightly dangerous, and give you cool sparks - so clearly this is the preferred method! biggrin

But I see we all recommend a very large hammer for the job biggrin


RizzoTheRat

29,150 posts

223 months

Monday 15th September 2008
quotequote all
smack said:
But I see we all recommend a very large hammer for the job biggrin
A real mans toolkit consists of two tools; a hammer and a roll of gaffer tape. If it moves and it shouldn't, tape it; if it should and doesn't, hit it with the hammer! cool

jon-

16,534 posts

247 months

Monday 15th September 2008
quotequote all
RizzoTheRat said:
smack said:
But I see we all recommend a very large hammer for the job biggrin
A real mans toolkit consists of two tools; a hammer and a roll of gaffer tape. If it moves and it shouldn't, tape it; if it should and doesn't, hit it with the hammer! cool
You forgot about cable ties and wd40. Then you could build a ship!

odyssey2200

18,650 posts

240 months

Monday 15th September 2008
quotequote all
Chain and Sprockets are not worth skimping on.
Cheap ones wear out quickly in my experiance.

But a DID O ring chain and decent sprockets.

Do Yanaha do an OE replacement?
I know Honda do.
They realised how much they were missing out on and came up with some very realistic prices for genuine kit.

Wasted Bullet

426 posts

283 months

Monday 15th September 2008
quotequote all
smack said:
Busamav said:
if you do go ahead and try it your self ( and i wouldnt recomend it either )

Do not remove the chain untill you have the engine sprocket loosened off
To do the job you will need:
Paddock stand
Hex / Alen keys
Screw drivers + and - ones
1/2 Drive socket set (with large sockets)
Possibly a bigger socket for wheel nut
Breaker Bar
Chain busting tool of your choice
Riveting tool
Big Hammer
Loctite
Torque wench

If your answer to anything on the list is "what's that", then take it to a shop. Or if your name is Chilli...
Chilli will have all the tools.... but they will still look new and unused, even though their 5 years old...