New hugger - too close to tyre?
New hugger - too close to tyre?
Author
Discussion

surfsofa

Original Poster:

406 posts

314 months

Monday 29th September 2008
quotequote all
Fitted a Pyramid hugger to my CBF yesterday. It's not sitting square over the wheel. I'm not so bothered about symmetry, but on one side it's looking very close to tyre (I reckon about 5mm). However much I try to adjust I can't seem to get a bigger gap.

Those with huggers - how does this look to you? This thing wasn't cheap, so if it's not right it might have to go back.







Edited by surfsofa on Monday 29th September 12:03

castrolcraig

18,073 posts

237 months

Monday 29th September 2008
quotequote all
huggers are meant to be close, so it isnt really a problem, however pyramid bits are not generally the greatest quality, people like ermax, evotech etc are much better bets.

Chilli

17,320 posts

267 months

Monday 29th September 2008
quotequote all
Not sure if it's right or not...but I have seen closer on every day road bikes.

dern

14,055 posts

310 months

Monday 29th September 2008
quotequote all
I'm pretty sure mine is as close as that but I wouldn't be happy with that fit from new.

Tazfan

1,186 posts

281 months

Monday 29th September 2008
quotequote all
Thats a little too close. The one that was fitted on my bike when I bought it sat too close as well, and it chipped the edge quite badly with stones that were dragged up with the tire.
I replaced it, but that one too sat too close. It didnt have the swinging arm part of it, so to raise it, all I did was put a couple of washers under the outermost bolts, with none in the middle. As I tightened the middle one, it lifted the rear of the hugger to the perfect position.
Then, for aesthetics as much as edge protection, I got some screen edging and put that all round the hugger. Looks ok I think.

ZZR

913 posts

282 months

Monday 29th September 2008
quotequote all
Bear in mind that the wheel rotation means the tyre travels into the edge of the hugger not from under it, if it catches it'll be possible to completely rip the hugger and/or tyre apart, I'd send it back and get a better quality/fitting one.

sprinter885

11,550 posts

258 months

Monday 29th September 2008
quotequote all
I've just been & measured my Ermax one on my Kwak ER6n.
It sits 3cm off the tyre in centre of tread at the tip of the hugger & about 1.5cm off at the side.
Quality of that is good I have to say.

surfsofa

Original Poster:

406 posts

314 months

Monday 29th September 2008
quotequote all
Thanks all. I'm wondering if a couple of washers might raise the offside enough. There are only 3 mountpoints on the hugger - 2 on the nearside and one on the offside which re-uses one of the P-clips that guide the brake lines along the swingarm. A couple of washers under that might do the trick. I reckon a centimetre would be enough clearance.

RemaL

25,103 posts

265 months

Monday 29th September 2008
quotequote all
I got a Skidmarx 1 fitted to my Speed triple and its close but never been a problem

Wyvern971

1,507 posts

239 months

Monday 29th September 2008
quotequote all
Might sound stupid, but is the wheel aligned correctly?

rumpelstiltskin

2,805 posts

290 months

Monday 29th September 2008
quotequote all
I used to have helluva problems with the hugger on my Busa.Hot sticky tyres,gravel driveway,you can guess the rest!