The worst as happend. Or has it?
Discussion
Was out riding with a mate on my Gilera GSM 50cc 2 stroke. Doing about 55mph over a hill when it nipped up. Pulled the clutch in and wheeled to the side of the road. Was moving in neutral but the kick start wasn't moving, pistons were ceased. But i got on the bike, put all my weight over the kickstart and it jerked and moved. So i kept pumping the kick start while it cooled down.
10mins after i tried starting it, nothing so i began the 10mile push home
Lucky, id only been going 2mins when a bloke in a Peugeot 406 estate pulled over and said if the bike will get in, he'll give us a lift home. He gave us a lift all the way home with half the bike hanging out the back of the car.
Couldn't thank him enough.
So now im lost, is it or isn't it ceased?
Any help is much appreciated.
Still a bit gutted its got to this point
10mins after i tried starting it, nothing so i began the 10mile push home

Lucky, id only been going 2mins when a bloke in a Peugeot 406 estate pulled over and said if the bike will get in, he'll give us a lift home. He gave us a lift all the way home with half the bike hanging out the back of the car.
So now im lost, is it or isn't it ceased?
Any help is much appreciated.
Still a bit gutted its got to this point

Sounds like it's gonna have to be stripped down, well atleast the top end anyway. If you're lucky its just the ring that stuck, though it has likely marked the barrell- but without seeing it I'm just guessing
a re-hone and piston or re-bore and piston shouldn't cost too much if that's all thats wrong with it
a re-hone and piston or re-bore and piston shouldn't cost too much if that's all thats wrong with it
Kurtblythman said:
pistons were ceased.
So now im lost, is it or isn't it ceased?
I can't see it being anything other than a single cylinder (with 1 piston)So now im lost, is it or isn't it ceased?
The engine may now be free, but there could be damage that will prevent it from working properly/at all
Edited by Brite spark on Saturday 4th October 15:32
Brite spark said:
Kurtblythman said:
pistons were ceased.
So now im lost, is it or isn't it ceased?
I can't see it being anything other than a single cylinder (with 1 piston)So now im lost, is it or isn't it ceased?
The engine may now be free, but there could be damage that will prevent it from working properly/at all
Edited by Brite spark on Saturday 4th October 15:32
When using the electric start it sounds horrible.


I had a 50cc 'ped many years ago as cheap transport and to make it cheaper I 'borrowed' some petrol from my Dad's garage but didn't have any 2-stroke oil, I thought it might be OK until I got to a ptol station where I could get some oil but it seized after about 2 or 3 miles, I let it cool down and it started again only to seize again. I pushed it home and took off the head, the piston had cracked luckily no other damage was caused but some 'cheap' fuel worked out more expensive than I had imagined - Happy days.
BTW 55mph is good going for a 50........
BTW 55mph is good going for a 50........
Asking the obvious did the bike still have plenty of 2-stroke oil in the tank? Back in the day i had a brand new DT-50 which i managed to run out of 2-stroke and hence the piston seized shortly after.
Was a quick lesson to learn..
On the plus side, Top-End rebuilds on 50's were very easy and was my first stab at bike mechanics. I'm sure it can't be too nasty on you're bike
Was a quick lesson to learn..
On the plus side, Top-End rebuilds on 50's were very easy and was my first stab at bike mechanics. I'm sure it can't be too nasty on you're bike
Kurtblythman said:
Forgot to mention before, its been rebored previously to a 70cc.
Will it be sensible, if needed, to rebore it again?
it all depends upon what the next size of piston that you can get, the increase should be tiny- so the cc won't really increase.Will it be sensible, if needed, to rebore it again?
If it's been changed to 70cc has the jetting been adjusted to compensate for this?
If it goes 50/55 has it not just been de-restricted? (shirley it would be a different cylinder head and not just a re-bore to get to 70cc)
Edited by Brite spark on Saturday 4th October 19:32
Brite spark said:
Kurtblythman said:
Forgot to mention before, its been rebored previously to a 70cc.
Will it be sensible, if needed, to rebore it again?
it all depends upon what the next size of piston that you can get, the increase should be tiny- so the cc won't really increase.Will it be sensible, if needed, to rebore it again?
If it's been changed to 70cc has the jetting been adjusted to compensate for this?
If it goes 50/55 has it not just been de-restricted? (shirley it would be a different cylinder head and not just a re-bore to get to 70cc)
Edited by Brite spark on Saturday 4th October 19:32
It does 65mph normaly but today, it was abit windy so it didnt want to go that fast and the gears wernt working right. I was traveling along in 5th and it was spluttering at 40mph and wouldnt go any quicker so i nocked it down one and it revved right up into the power band to about 45mph and then i went back up into fifth but it was redlineing at 11000rpm while doing 55mph when usualy its a brease at this speed.

Hmm well that is the trouble with mods on the bike if you don't know for sure what exactly was done.. Not a criticism... Most of us have bought modded bikes at one time or another...
Could be a host of things.. Perhaps the 2-stroke oil pump has failed.. maybe worth (once you've put it all back together) checking oil is feeding ok.
Also if you go from 50cc to 70cc technically you need to be pumping greater 2-stroke to match the increase of fueling.. Its possible the bike has been runnning a bit lean on the oil for some time and now it's finally given up.
Im only comparing this with my DT of years ago when i took it initially to 65cc and needed to add a little premix with the fuel to keep the 2-stroke mix ok.
Personally i'd whip the head and barrel off and take a look at the piston and rings. More than likely the piston / rings will be scored. Also check the condition of the barrel.
You should rebore the barrel but it is possible that if the barrel is ok and the piston has minimal damage you 'may' be able to replace the piston and rings only..
It looks like worst case scenario is £115 for a new 70cc barrel and piston kit.
Could be a host of things.. Perhaps the 2-stroke oil pump has failed.. maybe worth (once you've put it all back together) checking oil is feeding ok.
Also if you go from 50cc to 70cc technically you need to be pumping greater 2-stroke to match the increase of fueling.. Its possible the bike has been runnning a bit lean on the oil for some time and now it's finally given up.
Im only comparing this with my DT of years ago when i took it initially to 65cc and needed to add a little premix with the fuel to keep the 2-stroke mix ok.
Personally i'd whip the head and barrel off and take a look at the piston and rings. More than likely the piston / rings will be scored. Also check the condition of the barrel.
You should rebore the barrel but it is possible that if the barrel is ok and the piston has minimal damage you 'may' be able to replace the piston and rings only..
It looks like worst case scenario is £115 for a new 70cc barrel and piston kit.
Fire99 said:
Hmm well that is the trouble with mods on the bike if you don't know for sure what exactly was done.. Not a criticism... Most of us have bought modded bikes at one time or another...
Could be a host of things.. Perhaps the 2-stroke oil pump has failed.. maybe worth (once you've put it all back together) checking oil is feeding ok.
Also if you go from 50cc to 70cc technically you need to be pumping greater 2-stroke to match the increase of fueling.. Its possible the bike has been runnning a bit lean on the oil for some time and now it's finally given up.
Im only comparing this with my DT of years ago when i took it initially to 65cc and needed to add a little premix with the fuel to keep the 2-stroke mix ok.
Personally i'd whip the head and barrel off and take a look at the piston and rings. More than likely the piston / rings will be scored. Also check the condition of the barrel.
You should rebore the barrel but it is possible that if the barrel is ok and the piston has minimal damage you 'may' be able to replace the piston and rings only..
It looks like worst case scenario is £115 for a new 70cc barrel and piston kit.
Thanks.Could be a host of things.. Perhaps the 2-stroke oil pump has failed.. maybe worth (once you've put it all back together) checking oil is feeding ok.
Also if you go from 50cc to 70cc technically you need to be pumping greater 2-stroke to match the increase of fueling.. Its possible the bike has been runnning a bit lean on the oil for some time and now it's finally given up.
Im only comparing this with my DT of years ago when i took it initially to 65cc and needed to add a little premix with the fuel to keep the 2-stroke mix ok.
Personally i'd whip the head and barrel off and take a look at the piston and rings. More than likely the piston / rings will be scored. Also check the condition of the barrel.
You should rebore the barrel but it is possible that if the barrel is ok and the piston has minimal damage you 'may' be able to replace the piston and rings only..
It looks like worst case scenario is £115 for a new 70cc barrel and piston kit.
£100 is guna be alot to shell out considering i just payed £120 on Monday for the seals to be redone as there was gearbox oil getting into the engine.
Damn.
Kurtblythman said:
Thanks.
£100 is guna be alot to shell out considering i just payed £120 on Monday for the seals to be redone as there was gearbox oil getting into the engine.
Damn.
Thats interesting.. Do you know what gaskets were replaced. Its possible this job is what caused the seizure.. (i sound like a Doctor now. £100 is guna be alot to shell out considering i just payed £120 on Monday for the seals to be redone as there was gearbox oil getting into the engine.
Damn.
) If there was an air leak after the seal job then the bike would run lean and would seize..Anyway, you need someone handy with spanners to help you on this one i think.
So i'd say 1) check seal job was done right etc 2)take barrel off and inspect piston / barrel
Do that before being too gutted about it.
Fire99 said:
Kurtblythman said:
Thanks.
£100 is guna be alot to shell out considering i just payed £120 on Monday for the seals to be redone as there was gearbox oil getting into the engine.
Damn.
Thats interesting.. Do you know what gaskets were replaced. Its possible this job is what caused the seizure.. (i sound like a Doctor now. £100 is guna be alot to shell out considering i just payed £120 on Monday for the seals to be redone as there was gearbox oil getting into the engine.
Damn.
) If there was an air leak after the seal job then the bike would run lean and would seize..Anyway, you need someone handy with spanners to help you on this one i think.
So i'd say 1) check seal job was done right etc 2)take barrel off and inspect piston / barrel
Do that before being too gutted about it.
My dads now sure if we should take the barrel off because if we leave it to the guy at the shop to take it apart he might spot something wrong that we wouldnt of noticed.
Also something to note, before setting off (i only went about 10mile), the water level for the radiator was at the top because it was filled up before i left but now it is below the minimum level.

Edited by Kurtblythman on Saturday 4th October 23:52
Kurtblythman said:
Erm il have to ask my dad about that, i know he did replace something else as he had orderd a part that was 50cc but when he went to fit it noticed it was a 70 and had to reorder so i got the bike back a day or two later.
My dads now sure if we should take the barrel off because if we leave it to the guy at the shop to take it apart he might spot something wrong that we wouldnt of noticed.
Also something to note, before setting off (i only went about 10mile), the water level for the radiator was at the top because it was filled up before i left but now it is below the minimum level. :scratching:
Chances are that he had to take the barrel off to resolve the crankcase leak and had to buy a new cylinder base gasket for the barrel (which obviously will be bigger now with the 70cc one than the 50.. (still a guess mind)My dads now sure if we should take the barrel off because if we leave it to the guy at the shop to take it apart he might spot something wrong that we wouldnt of noticed.
Also something to note, before setting off (i only went about 10mile), the water level for the radiator was at the top because it was filled up before i left but now it is below the minimum level. :scratching:
Regarding the water level, well the barrel etc is water cooled so i'm guessing the barrel may not of been put on quite right (or the head torqued down correctly) which may have caused a water leak from the waterways and a possible air leak into the cylinder which ultimately caused the seize. Or on the other hand the waterway may have leaked into the barrel causing aqualock..
Either way its all guesswork and it may be worth getting the shop to check it out if you're dad isn't feeling too confident.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff



