Sprockets
Author
Discussion

Carl-H

Original Poster:

947 posts

237 months

Tuesday 7th October 2008
quotequote all
I think I read on here a few months back about someone who had a sprocket made for his bike. My sprockets are knackered (I think they are 'hooked' and its making the chain go tight) but as my bike is fairly rare (Yamaha FZX250) no one makes aftermarket sprockets and I may have to wait a while to get some from Japan and it will cost loads.

Was it B&C express or something like that? How much was it and did it take long to do. Is there any other way to get the sprockets?

Also I may put a few teeth on the back or drop a few off the front as I've figured it out and top gear is good for 150mph+ on the limiter. It's a 250 and will only just do the ton but I don't want to be redlining at 70 down the motorway. At the moment top gear is 1000 rpm above the speed (70mph is 8000rpm, 80mph 9000 etc. Redline is 15,000.

Thanks in advance, Carl

Edited by Carl-H on Tuesday 7th October 20:18

Carl-H

Original Poster:

947 posts

237 months

Thursday 9th October 2008
quotequote all
Anyone?

DR B

66 posts

221 months

Thursday 9th October 2008
quotequote all
Maybe these guys can help or put you in touch with sombody that can?

http://www.moto-racing.co.uk/formulastudent.html

Cheers

Deano

bobthepsycho

221 posts

266 months

Thursday 9th October 2008
quotequote all
http://www.pistonheads.com/gassing/topic.asp?h=0&a...

Yes, B+C express, I think it was a week turn around.


Busamav

2,954 posts

239 months

Thursday 9th October 2008
quotequote all
Carl-H said:
Also I may put a few teeth on the back or drop a few off the front as I've figured it out and top gear is good for 150mph+ on the limiter. It's a 250 and will only just do the ton but I don't want to be redlining at 70 down the motorway. At the moment top gear is 1000 rpm above the speed (70mph is 8000rpm, 80mph 9000 etc. Redline is 15,000.

Thanks in advance, Carl
I would go the way of altering the back and leave the front as is if possible .

Gives the chain an easier life.

Hooli

32,278 posts

231 months

Thursday 9th October 2008
quotequote all
Busamav said:
Carl-H said:
Also I may put a few teeth on the back or drop a few off the front as I've figured it out and top gear is good for 150mph+ on the limiter. It's a 250 and will only just do the ton but I don't want to be redlining at 70 down the motorway. At the moment top gear is 1000 rpm above the speed (70mph is 8000rpm, 80mph 9000 etc. Redline is 15,000.

Thanks in advance, Carl
I would go the way of altering the back and leave the front as is if possible .

Gives the chain an easier life.
what he said, just be aware if you take too many teeth off the rear you might need a shorter chain. i'd buy stock length if your only going down 3 or so teeth as shops can pop a link out easy enough as required.
oh 'one link' when removed from a chain looks like two links to me as they have to match the plates, so it'd be 2 of the rollers shorter due to the plates overlapping.

Carl-H

Original Poster:

947 posts

237 months

Thursday 9th October 2008
quotequote all
Thanks for the links. Wouldn't I need a few more teeth if I were to change the rear sprocket for more acceleration? I got some prices for OE parts today and the front sprocket was £55 + vat and delivery!!! and the back was £60 and the chain about £50. May have to wait 6-8 weeks for the front though as it would need to come from Japan.

I'm hoping the reason they are hard to get hold of is because of the pitch and not how they fit. Could I change the pitch as long as everything I put on is the same pitch?

A bike shop near me has a book full of dimensions so I will take them there tomorrow and see if they can match them.

Thanks, Carl

Hooli

32,278 posts

231 months

Thursday 9th October 2008
quotequote all
Carl-H said:
Wouldn't I need a few more teeth if I were to change the rear sprocket for more acceleration?
D'OH! yes you would so you might need a longer chain if you go up enough teeth. sorry brain dead moment earlier it seems.
yup you should be able to change the pitch if you change everything. the front sprockets ive done have all fitted on big coarse splines, it'll probably be a case of removing the old one compare to others to ensure they'll fit as i doubt thats in the dimensions listed.

Carl-H

Original Poster:

947 posts

237 months

Friday 10th October 2008
quotequote all
The back has 57 teeth and the front 17. I had to put it somewhere as I'd definitely forget lol. I think the dimensions should definitely be listed as Yamaha arnt gonna make a set of sprockets for one fairly unpopular bike are they?

Carl-H

Original Poster:

947 posts

237 months

Friday 10th October 2008
quotequote all
Right just put all the details into a calculator. Standard top gear is good for 145 and putting 3 on the back sprocket knocks top speed down to 129 and doing 69 at 8000 rpm.

Keeping the three extra on the back and taking 1 off the front brings top speed down to 122 but then at 8000 rpm its doing 65.

I don't need to do any motorway for work or anything and I don't use them very often at all if I'm honest.

The front sprocket was knackered. The back was hooked and there was only 1-2 mm adjustment left with the chain so definitely time to change.


  • All top speeds are at peek power (15000) not at the limiter (16000). Also all of the speeds would be actual speeds not clock figures.

Carl-H

Original Poster:

947 posts

237 months

Saturday 11th October 2008
quotequote all
Now, I know what sprockets I need but in they are JT sprockets and I didn't think much of them in the past.

The front is JTF425-17

The rear is JTR1847-57

How can I figure out what I need if I wanted Renthal sprockets for example?

Hooli

32,278 posts

231 months

Saturday 11th October 2008
quotequote all
if you know the pitch & the number of teeth couldnt you just ask for that?