NSR 125 power problem
Discussion
Just been out on my bike, and theres somthing definatly amiss, i opened it up in first, just to get up to speed, and as a 125, doesnt have much speed compaired to a big bike, but when i wound it on, got to the powerband, and it just wouldnt go into it, it was really labouring at 8k revs (redline at 11 and powerband starts tailing off just before 11), so i change up to second, see if it does the same, and as it gets to the power band, i get a big jolt forward, yeah it speeds up more, but something is up with it :/
only had it less than a week and was running perfect when i got it.
could it be something simple like dirty plug, or something more serious.
only had it less than a week and was running perfect when i got it.
could it be something simple like dirty plug, or something more serious.
hmmm, well i have never taken a bike apart before, apart from taking one panel of fairing off and the seat off lol.
well will have to take a look tomoro, might fit a irridium plug, thats spost to help with high revving engines I've heard.
as for the carbs, do you mean take the carb off and clean it, or take it off and disasemble and clean?
well will have to take a look tomoro, might fit a irridium plug, thats spost to help with high revving engines I've heard.
as for the carbs, do you mean take the carb off and clean it, or take it off and disasemble and clean?
check your plug first. Remove it, clean it, put it back and try it. if it is the same as before you will have saved yourself best part of a tenner. If it don't work right with your current plug, an irridium one won;t make any difference.
2 strokes are reknown for fouling. if it isn't the plug (mixture related) it will be your carb. The jets are very small holes that the petrol is fed through. These holes are a 1/100th maybe a 1/1000th of the size of your japs eye and block up very easy.
It's a simple operation to strip the carb and blow these through (you have a main and pilot jet) but you would be better getting a manual and following that with the aid of diagrams.
2 strokes are reknown for fouling. if it isn't the plug (mixture related) it will be your carb. The jets are very small holes that the petrol is fed through. These holes are a 1/100th maybe a 1/1000th of the size of your japs eye and block up very easy.
It's a simple operation to strip the carb and blow these through (you have a main and pilot jet) but you would be better getting a manual and following that with the aid of diagrams.
Could be something simple like a blocked air filter, have you checked that?
Basic checks are as above poster suggested, fuel, air, ignition first, then start checking for silly things like loose wire on battery, crap or low fuel, blocked fuel filter...
Do you give the bike plenty of stick when you ride it, in other words, could it be coked up exhaust?
Basic checks are as above poster suggested, fuel, air, ignition first, then start checking for silly things like loose wire on battery, crap or low fuel, blocked fuel filter...
Do you give the bike plenty of stick when you ride it, in other words, could it be coked up exhaust?
EvoBarry said:
Do you give the bike plenty of stick when you ride it, in other words, could it be coked up exhaust?
well, i do like to give it some, but when going round town i tend just to kick it into a high gear and keep at 30, but when NSL comes around, i open it up.havnt had time to have a look, just stuck it in the garage and tomoro will start pulling it apart.
how easy is it to take off, strip and clean carbs?? a hour jobbie or a lot longer?
ManicMushroom said:
could it have been that it was cold and i tryed to give it some when cold?? (had been sitting outside a pub this evening and was pretty cold) and no, i hadnt been drinking alchyhole )
Never give a bike (especially 2-stroke) some stick when the bike is cold!! These engines need to be well up to normal operating temperature before giving them any welly!!I agree with the others in that, check the plug is a nice light brown colour and if not, clean it or replace it.
Check the air filter is clean..
I'm not sure if the NSR has cable/hydraulic powervalve. That may be sticking.
But before you do anything and i mean anything, let the bike warm up completely then give it a good ride and see how it goes then.
ManicMushroom said:
(10-15 mins enought to warm up?)
With the current weather being a bit chilly i'd say a good 5 mins before pulling away then another 10 mins of moderate riding before giving the bike some welly...Just so you're 100% sure engine temperature isn't in the equation with the problem
I havnt really paid it much attention but every time i look at the water temp dial thingy, it is never off the bottom :/ or only a little bit above the lowest, is that normal? or is my bike just cool
lol.
might just be that i dont look at it when riding and only look at it after its been on for a short while
lol.might just be that i dont look at it when riding and only look at it after its been on for a short while
Edited by ManicMushroom on Monday 20th October 00:08
My point is that while you say you don't have the cash someone with experience may fix it very quickly because they've seen it before. The infamous "they all do that sir" problems that all verhicles have. By working through each possibility yourself without the experience you may visit a number of blind alleys first all of which cost you money. By all means look at filters and plugs because they're straight forward to do, but don't leap in to deep water just because you want to get stuck in.
A simple example would be your spark plug, you want to check the plug so you get the plug out. You want to save money and you don't have a torque wrench but you figure you can get away with it as the torque wrench will cost you 50 notes. You don't mean to but you accidentally strip the thread by over tightening the plug and then your simple investigation costs you lots of money and your bike is off the road until it's fixed ... I'm not saying it will happen to you, it's just a small possibility you might not have considered. Getting the right tools to get stuck in yourself will cost you money too but will save you plenty in the long term. If you have a mate with the necessary experience and tools that's ideal as you can learn from him/her.
A simple example would be your spark plug, you want to check the plug so you get the plug out. You want to save money and you don't have a torque wrench but you figure you can get away with it as the torque wrench will cost you 50 notes. You don't mean to but you accidentally strip the thread by over tightening the plug and then your simple investigation costs you lots of money and your bike is off the road until it's fixed ... I'm not saying it will happen to you, it's just a small possibility you might not have considered. Getting the right tools to get stuck in yourself will cost you money too but will save you plenty in the long term. If you have a mate with the necessary experience and tools that's ideal as you can learn from him/her.
One thing it'll almost certainly not be is a clogged air filter. The air in Britain is generally not that full of crap that it would clog a filter in one week.
However, one thing I have heard of is people carrying a spare bit of rag under the seat. On a lot of bikes the intake for the airbox is under the seat and at wide throttle settings the suction of the intake has been known to pull the rag in and choke off the engine. Again, probably not your issue but it's as well to think laterally
However, one thing I have heard of is people carrying a spare bit of rag under the seat. On a lot of bikes the intake for the airbox is under the seat and at wide throttle settings the suction of the intake has been known to pull the rag in and choke off the engine. Again, probably not your issue but it's as well to think laterally

ManicMushroom said:
but when going round town i tend just to kick it into a high gear and keep at 30
My guess is that's a major part of the problem. Highly tuned 2 strokes don't like it and will foul the plug in a few miles. You have to thrash them all the time, which is why there rubbish round townA friends 50cc Derbi Senda started hesitating just before the power band. With me on it (18st) it wouldn't even go into the powerband - just stayed at 6k revs (or whatever it was before the powerband kicked in) chugging along.
Turned out to be the piston and rings. Pulled well after these were replaced. I beleve it was a lack of compression that caused the issue. Like others have said though check the cheaper items first! My YZ250 goes through plugs like i go through pies, although i am a bit of a girl with the throttle.
Turned out to be the piston and rings. Pulled well after these were replaced. I beleve it was a lack of compression that caused the issue. Like others have said though check the cheaper items first! My YZ250 goes through plugs like i go through pies, although i am a bit of a girl with the throttle.
Gassing Station | Biker Banter | Top of Page | What's New | My Stuff



