Ground anchor - drilling in concrete
Ground anchor - drilling in concrete
Author
Discussion

dern

Original Poster:

14,055 posts

310 months

Friday 24th October 2008
quotequote all
My ground anchor was delivered yesterday so I set about installing it. I don't seem to be able to drill a hole in our driveway though. I have been supplied with a drill large enough (I think it's about 20mm wide and 100mm long) but started with smaller pilot drills but I can only get about 10-15mm down before it all stops. I assume I'm hitting pebbles in the concrete. Any tips on how to proceed or is it a case of digging a hole in it with a breaker, refilling with only concrete and then drilling that?

Thanks,

Mark

StevRS

443 posts

240 months

Friday 24th October 2008
quotequote all
Get extra drill bits and press on - your hands will be really sore by the time you're done!!

dern

Original Poster:

14,055 posts

310 months

Friday 24th October 2008
quotequote all
StevRS said:
Get extra drill bits and press on - your hands will be really sore by the time you're done!!
The only thing that stopped me doing that is that it isn't a case of drilling a certain amount per drill bit as the first drill bit did all the work and then stopped... subsequent drill bits did nothing except eventually break.

Fire99

9,868 posts

260 months

Friday 24th October 2008
quotequote all
Maybe you've hit a bit of stone or something rather tough that was in the mix on the driveway..

Might be worth giving you're local tool-hire shop a ring as they will no doubt have something (short of a kango) to get through it.

lawrence567

7,507 posts

221 months

Friday 24th October 2008
quotequote all
Maybe you've hit a knott in the wood..?

Beemer-5

7,897 posts

245 months

Friday 24th October 2008
quotequote all
Tool hire shop, yep.

Perhaps you've found gold!

aeropilot

40,922 posts

258 months

Friday 24th October 2008
quotequote all
As said.....you need a 'proper' drill from a hire shop....that's what I had to do to drill the holes for my ground anchor.

dern

Original Poster:

14,055 posts

310 months

Friday 24th October 2008
quotequote all
Ok, hire shop it is... seemed like such a simple job too wink

Cheers.

GreenV8S

31,027 posts

315 months

Friday 24th October 2008
quotequote all
I assume you're using a masonry bit in a hammer drill. Perhaps you could put a punch down the hole and belt it hard to try to crack whatever it is you've hit? Also try making a start on one of the other holes, you'll have to come back to this one eventually but you'll probably feel a lot better about it if the others have gone in OK.

dern

Original Poster:

14,055 posts

310 months

Friday 24th October 2008
quotequote all
GreenV8S said:
I assume you're using a masonry bit in a hammer drill. Perhaps you could put a punch down the hole and belt it hard to try to crack whatever it is you've hit? Also try making a start on one of the other holes, you'll have to come back to this one eventually but you'll probably feel a lot better about it if the others have gone in OK.
Yep, masonary bit. There's only one hole unfortunately - well, there' supposed to be one but there's 3 holes quite close together in the drive now all about 10mm deep while I was looking for the 'soft spot' wink

The punch idea is a good one, I'll try that. Thanks.

GreenV8S

31,027 posts

315 months

Friday 24th October 2008
quotequote all
dern said:
The punch idea is a good one, I'll try that. Thanks.
Don't forget the eye protection (and a BIG hammer!).

sprinter885

11,550 posts

258 months

Friday 24th October 2008
quotequote all
Beat me to it -was going to suggest a Rawlpunch to get through pebble (i reckon). Club hammer as V8 said with goggles.

Soovy

35,829 posts

302 months

Friday 24th October 2008
quotequote all


Gas pipe?

Beemer-5

7,897 posts

245 months

Friday 24th October 2008
quotequote all
On the wider issue, it's just bloody great, isn't it, that everything has to be bolted down in our society.......

sprinter885

11,550 posts

258 months

Friday 24th October 2008
quotequote all
That's why I never bolt the wife down...just in the hope........ wink

Muffles

516 posts

253 months

Friday 24th October 2008
quotequote all
When I drilled mine it was a pain too, supplied with a 17mm (IIRC) bit that eventually overheated blunted. Luckily I bought 2 ground anchors so had a spare, we managed to drill in the 4 required holes using a cup of water to keep the bit wet while drilling, but it took forever.

Eventually we just bought an SDS drill which absolutely tears through concrete - the second ground anchor was incredibly quick to drill compared to the first!!

Muffles

516 posts

253 months

Friday 24th October 2008
quotequote all

tf007071

29 posts

266 months

Friday 24th October 2008
quotequote all
SDS+ seconded... Possibly the best power tool I've ever bought.

I had an issue with my garage occasionally filling with water, and with one of these I was able to drill 4 x 25mm holes in the concrete base through to earth which allowed the water out whilst I had a 'discussion' with my neighbour about his downpipe emptying into my hopper.

dern

Original Poster:

14,055 posts

310 months

Friday 24th October 2008
quotequote all
Soovy said:
Gas pipe?
All the gas and water come in the other side of the drive way and would be a lot deeper than 10mm down.

trumpet600

3,527 posts

262 months

Friday 24th October 2008
quotequote all
Is it a fairly new drive? do you know its construction?

It could be that you have drilled in line with a bit of steel reinforcing.