Mk3 Mondeo Key Programming
Discussion
Morning,
I've checked on meg and am confused as to what I need to do to program a new key/remote... basically I don't know which bits apply to the mk3 and which to earlier cars. I have at the moment one key with a remote fob which disarms the alarm, opens the doors and starts the car and one master key (blue insert) which also opens the doors and starts the car. If I buy a new blade and get it but and a new remote fob can I program it up myself.
Thanks,
Mark
I've checked on meg and am confused as to what I need to do to program a new key/remote... basically I don't know which bits apply to the mk3 and which to earlier cars. I have at the moment one key with a remote fob which disarms the alarm, opens the doors and starts the car and one master key (blue insert) which also opens the doors and starts the car. If I buy a new blade and get it but and a new remote fob can I program it up myself.
Thanks,
Mark
The programming of the transmitters is carried out as follows:-
1. Unlock the vehicle.
2. Switch ignition lock to position I (Radio).
3. Wait until the LED indicator is lit (approximately 10 seconds).
4. Switch off and remove the key (must be done within 5 seconds of step 3) the LED indicator on the dash will remain ON.
5. Stand in front of the receiver on one of the front doors and aim the transmitter key at it.
6. Press either one of the two transmitter buttons and keep it pressed (must be done within 20 seconds of step 3).
7. When the LED on the transmitter is illuminated press the other button 3 to 5 times.
8. Release both buttons while still aiming at the receiver.
9. The system will acknowledge successful programming of the transmitter by causing the LED indicator on the dash and the LED on the transmitter to flash 5 times.
10. Repeat steps 5 to 9 with each of the other transmitters which are to be programmed.
11. When all transmitters have been programmed, switch on the ignition (it is not necessary to start the engine) then turn off again. This will cause the programmes for each transmitter to be stored within the system
1. Unlock the vehicle.
2. Switch ignition lock to position I (Radio).
3. Wait until the LED indicator is lit (approximately 10 seconds).
4. Switch off and remove the key (must be done within 5 seconds of step 3) the LED indicator on the dash will remain ON.
5. Stand in front of the receiver on one of the front doors and aim the transmitter key at it.
6. Press either one of the two transmitter buttons and keep it pressed (must be done within 20 seconds of step 3).
7. When the LED on the transmitter is illuminated press the other button 3 to 5 times.
8. Release both buttons while still aiming at the receiver.
9. The system will acknowledge successful programming of the transmitter by causing the LED indicator on the dash and the LED on the transmitter to flash 5 times.
10. Repeat steps 5 to 9 with each of the other transmitters which are to be programmed.
11. When all transmitters have been programmed, switch on the ignition (it is not necessary to start the engine) then turn off again. This will cause the programmes for each transmitter to be stored within the system
Oops - the above may be for older models - try this.
Remote Transmitter Programming (410040)
1. Note:
A maximum of four keyless entry remote transmitters can be programmed to the generic electronic module (GEM). Programming must be done at the same time for all the transmitters.
Note:
To enter programming mode, first make sure that the vehicle battery is fully charged and the anti-theft system is not armed or triggered (if equipped).
Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during programming.
2. Turn the ignition switch from position I to position II at least four times in six seconds.
3. Turn the ignition switch to position I.
4. The GEM is now in the learning mode.
5. Press and hold one of the buttons on the remote transmitter until a chime sounds. This indicates a new transmitter code has been successfully received.
6. After each successful programming, another 10 second learning mode is automatically entered, up to a maximum of four times.
7. To program additional transmitters, repeat step 5.
8. The system will leave the learning mode after the ignition switch is turned to position III, or if no new transmitter is programmed during the 10 seconds, or if four remote transmitters have been programmed.
9. Note:
An incorrect programming procedure does not affect the stored codes.
After successful programming, only the new programmed transmitters will be accepted.
10. Test all the programmed transmitters, by activating and deactivating the locking/unlocking functions.
Remote Transmitter Programming (410040)
1. Note:
A maximum of four keyless entry remote transmitters can be programmed to the generic electronic module (GEM). Programming must be done at the same time for all the transmitters.
Note:
To enter programming mode, first make sure that the vehicle battery is fully charged and the anti-theft system is not armed or triggered (if equipped).
Close all doors and fasten the safety belts to make sure conflicting chimes do not sound during programming.
2. Turn the ignition switch from position I to position II at least four times in six seconds.
3. Turn the ignition switch to position I.
4. The GEM is now in the learning mode.
5. Press and hold one of the buttons on the remote transmitter until a chime sounds. This indicates a new transmitter code has been successfully received.
6. After each successful programming, another 10 second learning mode is automatically entered, up to a maximum of four times.
7. To program additional transmitters, repeat step 5.
8. The system will leave the learning mode after the ignition switch is turned to position III, or if no new transmitter is programmed during the 10 seconds, or if four remote transmitters have been programmed.
9. Note:
An incorrect programming procedure does not affect the stored codes.
After successful programming, only the new programmed transmitters will be accepted.
10. Test all the programmed transmitters, by activating and deactivating the locking/unlocking functions.
This is how to get your Ford radio code, it is a detailed guide for ford stereo code recovery with a nice video tutorial.
Gassing Station | Ford | Top of Page | What's New | My Stuff