Spring Question
Spring Question
Author
Discussion

V8 Animal

Original Poster:

6,015 posts

241 months

Monday 8th December 2008
quotequote all
Can't get this thought out of my head.
I have suffered from a small amount of bounce mainly on the front ever since ive fitted gaz shocks.
Im not prepared to replace them before you saysmile
Adjusting the rebound (clicks) marginally alters this but i can't eliminate it.
Before i try this just a thought is it ride height?
If you increase the ride height you tension the spring and if you decrease it you un tension the spring.
I wonder if i have too much ride height and the valving can't correct it causing a bounce.
It's not there all the time mostly on smoother roads.
If you compress a biro spring between your fingers you will get my point.
Am i talking rubbish or is there some truth in my madness?
V8 Animal

daz the plumber

14,997 posts

262 months

Monday 8th December 2008
quotequote all
i would never buy gaz again ,i think they are c..p.ive adjusted them so many times and i can not find a happy medium ,there eather soft and bouncy or very hard .never again !

spend

12,581 posts

282 months

Monday 8th December 2008
quotequote all
V8 Animal said:
If you increase the ride height you tension the spring and if you decrease it you un tension the spring.
I'd think about that again if I was you? pre-load will be the same just the platform higher/lower, as long as you are within the range of the damper travel.

Things are actually lighter if you move them away from the core of the earth I believe hehe

V8 Animal

Original Poster:

6,015 posts

241 months

Monday 8th December 2008
quotequote all
spend said:
V8 Animal said:
If you increase the ride height you tension the spring and if you decrease it you un tension the spring.
I'd think about that again if I was you? pre-load will be the same just the platform higher/lower, as long as you are within the range of the damper travel.

Things are actually lighter if you move them away from the core of the earth I believe hehe
Had them over 6 months now so been thinking about it for a while.
If im wrong fair enough.

GreenV8S

31,027 posts

315 months

Monday 8th December 2008
quotequote all
Have you spoken to your supplier about it? I'm sure they'd be happy to advise if you asked them.

V8 Animal

Original Poster:

6,015 posts

241 months

Monday 8th December 2008
quotequote all
GreenV8S said:
Have you spoken to your supplier about it? I'm sure they'd be happy to advise if you asked them.
Yes but about bounce not ride height.
The answer was as these are fully adjustable it is down to customer choice.
Gaz are right in their answer IMO
Maybe i'll play with the ride heights on a dry warm day.
Or maybe as daz has repeatedly said there crap which ive not ruled out.

GreenV8S

31,027 posts

315 months

Monday 8th December 2008
quotequote all
V8 Animal said:
GreenV8S said:
Have you spoken to your supplier about it? I'm sure they'd be happy to advise if you asked them.
Yes but about bounce not ride height.
The answer was as these are fully adjustable it is down to customer choice.
Gaz are right in their answer IMO
Maybe i'll play with the ride heights on a dry warm day.
Or maybe as daz has repeatedly said there crap which ive not ruled out.
I'm not sure exactly what you think is wrong, but I can't think of any way that changing the ride height is going to affect the spring/damping characteristics, unless you're running out of travel. However, changing the ride height can make a huge difference to the steering feel and completely eff up the geometry.

V8 Animal

Original Poster:

6,015 posts

241 months

Saturday 24th January 2009
quotequote all
Had some success with my shocks.
In the week took my car to work(not busyfrown) and adjusted the ride height lowered the rear 15mm and the front 5mm
Steering is lighter and ride is smooth increased the rear clicks to 14 from 10 and still no jigger that ive always had.
Next time i take it on a run i'll increase the rears to 16 may well reach the common 18 fronts unchanged at 12
Adjusting ride height seems to have let me increase the damping by 4 clicks at the moment.
Picture taken today rear arch clearance was double that and front slightly.
BTW SHWMBO Put her foot down over the our sons exhaust and told him to put the old one backlaugh
V8 Animal

bigdods

7,175 posts

258 months

Saturday 24th January 2009
quotequote all
Front still looks a bit high , mine only has a tiny gap between wheel and arch. My rears look about the same, maybe yours is a touch lower. Would be interested to know what the ride height is now and compare notes with you... not sure where best to measure it from, maybe the front and rear end of each outrigger would be a good point ?

V8 Animal

Original Poster:

6,015 posts

241 months

Saturday 24th January 2009
quotequote all
bigdods said:
Front still looks a bit high , mine only has a tiny gap between wheel and arch. My rears look about the same, maybe yours is a touch lower. Would be interested to know what the ride height is now and compare notes with you... not sure where best to measure it from, maybe the front and rear end of each outrigger would be a good point ?
I know this isn't the correct method but good for a cross reference.
25mm front 40mm rear taken from start adjuster groove to underneath of locking ring.
As for correct method i'll talk to derek he did tell me but i can't remember.

Edited by V8 Animal on Saturday 24th January 22:17

spend

12,581 posts

282 months

Saturday 24th January 2009
quotequote all
I reckon the only consistent method is to the main chassis rails, I wouldn't rely on the outriggers, or anywhere else for that matter, being the same. Personally I put a window board upto the tyres (inside the wheelbase) and measure vertically from that to the chassis rails (with car on my wooden planksramps).