my next project
my next project
Author
Discussion

daz the plumber

Original Poster:

14,997 posts

262 months

Monday 8th December 2008
quotequote all

Chimjunkie

2,879 posts

242 months

Monday 8th December 2008
quotequote all
Nice link wink

daz the plumber

Original Poster:

14,997 posts

262 months

Monday 8th December 2008
quotequote all
i would love to lift my bonnet and see that ,here is a full run down how the guy built it, its not carbs ,full injection with meagasquirt ,im amazed, wish it was a bolt on kit .http://www.britishv8.org/Articles/MGB-V8-Supercharger.htm

Edited by daz the plumber on Monday 8th December 23:13

scotty_d

6,795 posts

225 months

Tuesday 9th December 2008
quotequote all
That is one big hair dryer bolted to that. Want onebiggrin

thegman

1,928 posts

235 months

Tuesday 9th December 2008
quotequote all
daz the plumber said:
so is your project fuel injection or supercharger or both

SimonV8ster

13,039 posts

259 months

Tuesday 9th December 2008
quotequote all
Holy Moly !! yikes

I'm really not sure whether I could live with something looking that good ? You'd spend more time cleaning up after your hoon (if you took it anywhere) than you would driving it !.

spend

12,581 posts

282 months

Tuesday 9th December 2008
quotequote all
thegman said:
daz the plumber said:
so is your project fuel injection or supercharger or both
What about a pipe to the plenum that runs to a hand held blow torch so he you just add gas on demand hehe Seems a suitable plumbers solution rofl

daz the plumber

Original Poster:

14,997 posts

262 months

Tuesday 9th December 2008
quotequote all
sorry i have no blow torch i use plastic pipe lol

chedder

1,329 posts

238 months

Tuesday 9th December 2008
quotequote all
spend said:
thegman said:
daz the plumber said:
so is your project fuel injection or supercharger or both
What about a pipe to the plenum that runs to a hand held blow torch so he you just add gas on demand hehe Seems a suitable plumbers solution rofl
I'm a Plumber and have a pipe to the plenum that injects gas but it isn't butane......
A wee drop of nitrous instead!

Good luck with the supercharger install, here's one I prepared earlier on my Wedge!

If you need any info or help....give me a shout.

Chedder

daz the plumber

Original Poster:

14,997 posts

262 months

Tuesday 9th December 2008
quotequote all
i was joking about the project , i don`t have a clue , i just liked the picture ,did you build your own and what bhp do you have .i wonder why people don`t go for the more traditional super charger . you can get a bolt on super charger kit for for a mgb why not a v8 .how does your`s work as the other charger does not use the plenum . http://www.britishv8.org/Articles/MGB-V8-Superchar... copy and paste this ,there is a full page on it .

Edited by daz the plumber on Tuesday 9th December 18:41

V8 Animal

6,015 posts

241 months

Tuesday 9th December 2008
quotequote all
Daz,
There's a few on here with superchargers on the v8 also known as blowers.
Can't remember the guy who sells them but someone will pop up and tell you.

chedder

1,329 posts

238 months

Tuesday 9th December 2008
quotequote all
daz the plumber said:
i was joking about the project , i don`t have a clue , i just liked the picture ,did you build your own and what bhp do you have .i wonder why people don`t go for the more traditional super charger . you can get a bolt on super charger kit for for a mgb why not a v8 .how does your`s work as the other charger does not use the plenum . http://www.britishv8.org/Articles/MGB-V8-Superchar... copy and paste this ,there is a full page on it .

Edited by daz the plumber on Tuesday 9th December 18:41
Hi Daz, not that difficult to fit really, fair amount of head and ass scratching on where to locate the M90 blower and intercooler pipework without modding the body, bonnet or inner wing, Practical Performance Car mag ran a series of articles about a year ago and I just followed them more or less.
Car is converted from a V6 to a 3.5L and makes around 285hp at the flywheel on 5 lbs of boost plus an extra 50hp on the nitrous. Just about to bin the lucas EFI system in favour of an Emerald ecu with coil packs, so that should liberate a few more ponies and more money from my wallet!

GO ON GO ON GO ON........You know you want one! smokin

Edited by chedder on Tuesday 9th December 19:28

Pupp

13,043 posts

303 months

Tuesday 9th December 2008
quotequote all
chedder said:
daz the plumber said:
i was joking about the project , i don`t have a clue , i just liked the picture ,did you build your own and what bhp do you have .i wonder why people don`t go for the more traditional super charger . you can get a bolt on super charger kit for for a mgb why not a v8 .how does your`s work as the other charger does not use the plenum . http://www.britishv8.org/Articles/MGB-V8-Superchar... copy and paste this ,there is a full page on it .

Edited by daz the plumber on Tuesday 9th December 18:41
Hi Daz, not that difficult to fit really, fair amount of head and ass scratching on where to locate the M90 blower and intercooler pipework without modding the body, bonnet or inner wing, Practical Performance Car mag ran a series of articles about a year ago and I just followed them more or less.
Car is converted from a V6 to a 3.5L and makes around 285hp at the flywheel on 5 lbs of boost plus an extra 50hp on the nitrous. Just about to bin the lucas EFI system in favour of an Emerald ecu with coil packs, so that should liberate a few more ponies and more money from my wallet!

GO ON GO ON GO ON........You know you want one! smokin

Edited by chedder on Tuesday 9th December 19:28
That's a neat looking install... is the M90 running flat out to make 5psi or is there headroom for more boost to be achieved?

Be interested to see some shots of the mountings etc smile

chedder

1,329 posts

238 months

Tuesday 9th December 2008
quotequote all
Pupp said:
chedder said:
daz the plumber said:
i was joking about the project , i don`t have a clue , i just liked the picture ,did you build your own and what bhp do you have .i wonder why people don`t go for the more traditional super charger . you can get a bolt on super charger kit for for a mgb why not a v8 .how does your`s work as the other charger does not use the plenum . http://www.britishv8.org/Articles/MGB-V8-Superchar... copy and paste this ,there is a full page on it .

Edited by daz the plumber on Tuesday 9th December 18:41
Hi Daz, not that difficult to fit really, fair amount of head and ass scratching on where to locate the M90 blower and intercooler pipework without modding the body, bonnet or inner wing, Practical Performance Car mag ran a series of articles about a year ago and I just followed them more or less.
Car is converted from a V6 to a 3.5L and makes around 285hp at the flywheel on 5 lbs of boost plus an extra 50hp on the nitrous. Just about to bin the lucas EFI system in favour of an Emerald ecu with coil packs, so that should liberate a few more ponies and more money from my wallet!

GO ON GO ON GO ON........You know you want one! smokin

Edited by chedder on Tuesday 9th December 19:28
That's a neat looking install... is the M90 running flat out to make 5psi or is there headroom for more boost to be achieved?

Be interested to see some shots of the mountings etc smile
The blower is geared for 8psi at 5800 rpm, but due to the limits of the Lucas EFI set up to provide the required fueling, it is currently bleeding off 3 psi through a dump valve plumbed to act like a wastegate, here's a few pics during the build;

The 'before' shot

New big valve heads

Mocking up the mounting for the blower

Shot of the finished mounting plate

Nearly there shot!

Intercooler trial fitting

The beasty back on the road



Seems strange posting Wedge pics on the Chim section! So apologies in advance

daz the plumber

Original Poster:

14,997 posts

262 months

Tuesday 9th December 2008
quotequote all
why is it the picture i posted have the blower sitting on the engine and the inlet plenum as been removed .www.britishv8.org/Articles/MGB-V8-Supercharger.htm

chedder

1,329 posts

238 months

Tuesday 9th December 2008
quotequote all
daz the plumber said:
why is it the picture i posted have the blower sitting on the engine and the inlet plenum as been removed .www.britishv8.org/Articles/MGB-V8-Supercharger.htm
This one?

Markh

2,781 posts

306 months

Tuesday 9th December 2008
quotequote all
daz the plumber said:
why is it the picture i posted have the blower sitting on the engine and the inlet plenum as been removed .www.britishv8.org/Articles/MGB-V8-Supercharger.htm
This may shed some light on why

http://www.v8engines.com/engine-3b-big-1.htm#Middl...

daz the plumber

Original Poster:

14,997 posts

262 months

Wednesday 10th December 2008
quotequote all
, i have not seen any one with the same set up .how does it work ,the plenum as gone but the fuel injection and everything else is there .have agood look at this http://www.britishv8.org/Articles/MGB-V8-Superchar...

Edited by daz the plumber on Wednesday 10th December 21:08
copy and paste

Edited by daz the plumber on Wednesday 10th December 21:22

chedder

1,329 posts

238 months

Thursday 11th December 2008
quotequote all
daz the plumber said:
, i have not seen any one with the same set up .how does it work ,the plenum as gone but the fuel injection and everything else is there .have agood look at this http://www.britishv8.org/Articles/MGB-V8-Superchar...

Edited by daz the plumber on Wednesday 10th December 21:08
copy and paste

Edited by daz the plumber on Wednesday 10th December 21:22
Hi Daz, the problem with the Eaton M90 type of blower is the relatively small outlet (approx 4" square) compared to the top of the inlet manifold ( 13" x 4") if mounting the blower on the top of the engine, this can cause issues getting good airflow to all cylinders. If you have a very tall engine bay then it isn't much of an issue but as can be seen in the photos, the MGB and my Tasmin have very little clearance between the top of the engine and the bonnet, and the MGB has used a very flattened inlet manifold to achieve clearance, I retained the plenum to get equal flow to all 8 cylinders but had to side mount the blower as a result and enable me to use an intercooler.
Yanks overcome the clearance problems by mounting the blower much higher normally above a charge cooler and you often see them with it stuck through the top of the bonnet or hidden under a huge bonnet bulge....looks great! But crap for forward visability.

VerySideways

10,272 posts

303 months

Thursday 2nd April 2009
quotequote all
Have to resurrect this thread - i put my Honda Blackbird up for sale and jokingly mentioned that i would take a supercharger for a Chim in part-ex.

Got a phone call from a chap saying he has a brand new Eaton M90 in a box and offering me a good deal to swap for the bike+cash.

SO - anyone mounted an M90 to a Chim, and if so was in "on top" or off to the side? I'm not keen on the "on top" idea due to the airflow (as has been discussed) but an installation like that shown in the wedge earlier in this thread (very nice!) would tempt me, i'm just not sure the Chim engine bay has the width to accomodate that sort of install.

Anyone shed any light? Thanks.