twin airflow meters...can it be done...?
Discussion
i was wondering if anyone knew what the chances of putting a second AFM on the chim would be?
I am going for a twin plenum and dont want to run it through the one AFM as that would defeat the point a bit...
Can anyone see any problems???
Eventually i will be going megasquirt but that is a way off yet so i need a temporary measure for now
I am going for a twin plenum and dont want to run it through the one AFM as that would defeat the point a bit...
Can anyone see any problems???
Eventually i will be going megasquirt but that is a way off yet so i need a temporary measure for now
I've been scratching my head on this - and theoretically it sounds possible.
My thoughts were to engineer two airflow meters into the air inlet - but to only connect one of them but with a bit of simple electronics bump up the output voltage so that it reflects the airflow through both meters.
Theoretically both meters should have the same airflow so I wouldn't over complicate it trying to connect both of them.
I'm sure in reality there are lots of issues that mean this won't work.
My thoughts were to engineer two airflow meters into the air inlet - but to only connect one of them but with a bit of simple electronics bump up the output voltage so that it reflects the airflow through both meters.
Theoretically both meters should have the same airflow so I wouldn't over complicate it trying to connect both of them.
I'm sure in reality there are lots of issues that mean this won't work.
Barkychoc said:
I've been scratching my head on this - and theoretically it sounds possible.
My thoughts were to engineer two airflow meters into the air inlet - but to only connect one of them but with a bit of simple electronics bump up the output voltage so that it reflects the airflow through both meters.
Theoretically both meters should have the same airflow so I wouldn't over complicate it trying to connect both of them.
I'm sure in reality there are lots of issues that mean this won't work.
What's the second one for then - restricting the air flow to the same extent as the functioning one on the other side? My thoughts were to engineer two airflow meters into the air inlet - but to only connect one of them but with a bit of simple electronics bump up the output voltage so that it reflects the airflow through both meters.
Theoretically both meters should have the same airflow so I wouldn't over complicate it trying to connect both of them.
I'm sure in reality there are lots of issues that mean this won't work.
900T-R said:
What's the second one for then - restricting the air flow to the same extent as the functioning one on the other side?
eventually they will both go...i am making a new plenum...was thinking of doing the siamese one but am now thinking of going for two separate boxes, one to feed each bank...for now i was thinking of using two AFM's until i get the megasquirt...IIRC the car stops running if you just disconnect the existing AFM, and i dont want to run the two through one AFM900T-R said:
Barkychoc said:
I've been scratching my head on this - and theoretically it sounds possible.
My thoughts were to engineer two airflow meters into the air inlet - but to only connect one of them but with a bit of simple electronics bump up the output voltage so that it reflects the airflow through both meters.
Theoretically both meters should have the same airflow so I wouldn't over complicate it trying to connect both of them.
I'm sure in reality there are lots of issues that mean this won't work.
What's the second one for then - restricting the air flow to the same extent as the functioning one on the other side? My thoughts were to engineer two airflow meters into the air inlet - but to only connect one of them but with a bit of simple electronics bump up the output voltage so that it reflects the airflow through both meters.
Theoretically both meters should have the same airflow so I wouldn't over complicate it trying to connect both of them.
I'm sure in reality there are lots of issues that mean this won't work.
Barkychoc said:
Yes - I figured you need the same venturi to get away with only one meter being connected - the easiest way I thought is just to use another meter - it doesn't even need to work.
good point...one bank will be drawing roughly the same as the other...hmmmmmm...getting more confusing now 
There was a guy a year or two back, either on here or the TVRCC forum, I can't remember which. He had two plenum chamber tops that he had cut vertically lengthways and then joined together the two halves to make a chamber with two air inlets. He'd knocked up some electronics to combine the two AFM signals giving the 14CUX the proper voltage corresponding to the actual airflow. I don't know if he finished the job, or how he connected the two throttles together.
OK - Thinking about this in its basic form - what we need is some data for the standard setup.
In its most basic form it would be the AFM output with the standard single plenum at various rpm on the engine - maybe if you're feeling really ambitious and have an accompice you could even get some data with the car on the move - some simple logging of voltages at various levels of rpm.
In its most basic form it would be the AFM output with the standard single plenum at various rpm on the engine - maybe if you're feeling really ambitious and have an accompice you could even get some data with the car on the move - some simple logging of voltages at various levels of rpm.
Andy it would be great in theory but a bloody nightmare to get those AFM,s to meter output properly to the ECU,me personally hold out for the Megasquirt or whatever you choose to use(like the sound of that plenum idea though)oh yeh,hows it going mate
and when you gonna update your profile pics 

Cider Andy said:
There was a guy a year or two back, either on here or the TVRCC forum, I can't remember which. He had two plenum chamber tops that he had cut vertically lengthways and then joined together the two halves to make a chamber with two air inlets. He'd knocked up some electronics to combine the two AFM signals giving the 14CUX the proper voltage corresponding to the actual airflow. I don't know if he finished the job, or how he connected the two throttles together.
You're not thinking of Phil Ringwood are you?Chimjunkie said:
Like the idea of using the two meters and just connecting the one.
I have been thinking about that...if i half the plenum then there will only be half the air flow so it would be reading weak...?Surely the AFM would be expecting a draw for 8 cylinders instead of 4...if it was just drawing air for 4 then it would only upply the fuel for 4...unless i have had too many beers and am not thinking straight...
That Daddy said:
Andy it would be great in theory but a bloody nightmare to get those AFM,s to meter output properly to the ECU,me personally hold out for the Megasquirt or whatever you choose to use(like the sound of that plenum idea though)oh yeh,hows it going mate
and when you gonna update your profile pics 
Well i can do most of the mods and just use the one AFM but it will not be ideal as running throughh the one AFM would kind of defeat the object...as for updating the profile pics i shall try and do it now...
The suggestion was just to connect one AFM - but it will need some simple electronics (theoretically) to increase the voltage to the level it would be at with all the air going through one AFM - does that make sense?
The problem is that we have no reference data what these values need to be.
Thinking again it might be easier to connect both AFM's to a simple electronic circuit that adds both voltages together (this is easy to do) then divides it by 2, again easy to do. This should again theoretically give the normal idle value.
The question would be at idle with half the normal level of air going through the AFM is it still within the operating range of the AFM or maybe it won't register at this new lower level of airflow.
If someone has done it before it would be worth finding out what they did and if it worked - no point reinventing the wheel IMHO.
The problem is that we have no reference data what these values need to be.
Thinking again it might be easier to connect both AFM's to a simple electronic circuit that adds both voltages together (this is easy to do) then divides it by 2, again easy to do. This should again theoretically give the normal idle value.
The question would be at idle with half the normal level of air going through the AFM is it still within the operating range of the AFM or maybe it won't register at this new lower level of airflow.
If someone has done it before it would be worth finding out what they did and if it worked - no point reinventing the wheel IMHO.
You're just asking for a lot of grief Andy, IMHO. If you stick another ecu on it and map of pressure it will have been a complete waste of time and effort.
Just do it when you install your MS (you're intention I believe). If you plan to have banked plenums you will need a balance pipe, just take map (pressure) sensor off that... No need for AFM('s) at all in that case. Much less grief
ETA: self policing grammar variety
Just do it when you install your MS (you're intention I believe). If you plan to have banked plenums you will need a balance pipe, just take map (pressure) sensor off that... No need for AFM('s) at all in that case. Much less grief

ETA: self policing grammar variety

Edited by spend on Monday 29th December 23:14
spend said:
If you plan to have banked plenums you will need a balance pipe, just take map (pressure) sensor of that... No need for AFM('s) at all in that case. Much less grief 
now that sounds good...use the MAP sensor on the MS and have a pipe running from each plenum to a to 'T' peice running to the MS...think what i am going to do is build the parts first, fit the MS and then put the twin plenums on...
Just need to put a shopping list together now...!
andy-w said:
spend said:
If you plan to have banked plenums you will need a balance pipe, just take map (pressure) sensor of that... No need for AFM('s) at all in that case. Much less grief 
now that sounds good...use the MAP sensor on the MS and have a pipe running from each plenum to a to 'T' piece running to the MS...think what i am going to do is build the parts first, fit the MS and then put the twin plenums on...
Just need to put a shopping list together now...!
I still would not really advocate that however, 2 side by side throttles on a single plenum is much easier, getting rid of the horrible RV8 letterbox and S shape behind the throttle would be a massive improvement IMHO. Beyond that if you start playing with the inlet manifold the world is your oyster I reckon
If you want some alternate ideas contact me offline, I've done quite a lot of research into different methods and even created some DXF of manifold flanges, they look really funky prototyped in plastic.Gassing Station | Chimaera | Top of Page | What's New | My Stuff


