ECU Probs ?
ECU Probs ?
Author
Discussion

Mr Haribo

Original Poster:

318 posts

220 months

Saturday 3rd January 2009
quotequote all
I have trouble with the car starting, I did drive it before I put it away for the winter but it was very lumpy and seemed flat.I have put new spark plugs in.
I have got a good spark and theres fuel going in !
so my thought is either the timing has moved ?
Or could it be the ECU over fueling as the new plugs are soaked again ?
Has anyone any ideas thanks in advance

blitzracing

6,422 posts

251 months

Sunday 4th January 2009
quotequote all
The ECU's do put a lot of fuel in to start the car, its not a fault its a "feature" and is part of the fuel map. This means if the car does not start faily rapidly the plugs become very wet very quickly, so it will never go. Take the plugs out and get them dry in an oven or with a blow torch, and hopefully the engine will dry out when the plugs are out. It will help if the plugs are still warm when you put them back in and give it another go. As for sparks, dont be 100% sure that just because you have a spark in free air, it will be the same in the combustion chamber as conditions are a lot harder for the ignition. Mind you a spark that weedy is faily obvious. Dont blame the ECU itself, as you said, you have fuel.

mariner

79 posts

249 months

Sunday 4th January 2009
quotequote all
You could try pulling the blue relay on the loom in the passenger footwell. This controls the fuel pump. It will give you the option to turn the car over with no fuel to clear the cylinders and then replace and try to start. Worked for me once.
Final problem turned out to be the coil and amplifier pack. Once replaced vroom!.
I have replaced these two bits twice in 5 years. They don't like the heat.

Mr Haribo

Original Poster:

318 posts

220 months

Sunday 4th January 2009
quotequote all
Is it worth investing in a standard amp or a rpi one ?
If I ring rpi its going to be a long call ect !!!!

spend

12,581 posts

282 months

Sunday 4th January 2009
quotequote all
Mr Haribo said:
Is it worth investing in a standard amp or a rpi one ?
If I ring rpi its going to be a long call ect !!!!
If you call RIP they will undoubtedly try and sell you one of theirs, I don't believe Billy Graham died, he must have sneaked in through one of their crate engine rofl

A spare is really worthwhile in any case, they are extremely hard to diagnose as they don't 'fail completely'. Stick with the Lucas version rather than one of the Charlatan alternatives wink

Mr Haribo

Original Poster:

318 posts

220 months

Sunday 25th January 2009
quotequote all
I am lost again ! I have put in 8 new plugs and a new lucas Dab 118 ignition module, a new coil and leads and it still does not start! it does try, and now the Ecu warning light is now on. I took out two plugs today 2 and 4 one was wet the other dry ?????
This is a modded ecu with a bosch air flow meter so im not sure if i can take it to my local car parts factors for a ecu test ?? or is it even the ecu ?


spend

12,581 posts

282 months

Sunday 25th January 2009
quotequote all
Inspect all of them, you may have an injector stuck open (or even wiring fault). You could try pulling the connector of the troublesome injector - if it is just bleeding too much on accuation?

Generally cars will start to fire with fuel pump off, you can try cranking with just the bit in the fuel rail, to avoid flooding.

GreenV8S

31,027 posts

315 months

Sunday 25th January 2009
quotequote all
Mr Haribo said:
I am lost again ! I have put in 8 new plugs and a new lucas Dab 118 ignition module, a new coil and leads and it still does not start! it does try, and now the Ecu warning light is now on. I took out two plugs today 2 and 4 one was wet the other dry ?????
This is a modded ecu with a bosch air flow meter so im not sure if i can take it to my local car parts factors for a ecu test ?? or is it even the ecu ?
There are not many people who can test this ECU except by substitution. But if it won't start you can go quite a long way using basic faulting techniques before you resort to that.

If the plugs are wet you have fuel in the chamber so it should be possible to get it to fire. Since it isn't firing it is extremely likely to be flooded by now so get the plugs out and cleaned up, ideally fit new ones but if you're flooding them repeatedly trying to start it then personally I would clean and refit to save money. Remember you only need to tighten through a quarter turn if you're reusing them.

You need to confirm you are getting a spark. The quick and easy test is to sit the plug on the rocker cover and look for a spark when cranking. A more thorough test is to put a passive strobe in line with one of the HT leads and show you're getting current while cranking with the plugs actually fitted. Do the test at a plug lead and on the king lead; you should see a similar spark in both places. If you're mechanically competent then take the dizzy cap off and check that the rotor arm is secure and intact, the cap is clean and unmarked (no tracks or cracks anywhere) and the contacts and center brush are all OK. If you have plug extenders, remove them to rule them out. (Refit/replace once the engine has been started.)

While you're cranking it over you're injecting more and more petrol and will quickly flood it so it won't start even if you were to find/fix any other problems. So if it won't go after ten seconds disable the fuel pump before you do any more testing. If the plugs are coming out bone dry then you know it's time to enable the pump again for another ten seconds.

It's much harder to start if the battery is running down even if everything else is OK, so be sure to keep the battery charged up while you're doing all this.

loud430

550 posts

214 months

Wednesday 28th January 2009
quotequote all
hi, just thought id ask, probably silly question but if you have some plugs dry & some wet when trying to start the car & the ecu warning lights come on, would this point to a problem with the injector timing? hope you get it sorted out soon!

GreenV8S

31,027 posts

315 months

Wednesday 28th January 2009
quotequote all
loud430 said:
would this point to a problem with the injector timing?
No, I don't think that's a problem. The way it works is that the ECU triggers all the injectors on one bank together, then it triggers the other bank. They aren't phased with the combustion cycle or anything like that.

loud430

550 posts

214 months

Wednesday 28th January 2009
quotequote all
sorry, ive not had much experience with the Rv8 yet! didnt know which way the injectors fired, forgot to ask whether the wet & dry plugs were in the same bank, would that make any difference?

blitzracing

6,422 posts

251 months

Thursday 29th January 2009
quotequote all
Mr Haribo said:
I am lost again ! I have put in 8 new plugs and a new lucas Dab 118 ignition module, a new coil and leads and it still does not start! it does try, and now the Ecu warning light is now on. I took out two plugs today 2 and 4 one was wet the other dry ?????
This is a modded ecu with a bosch air flow meter so im not sure if i can take it to my local car parts factors for a ecu test ?? or is it even the ecu ?
Just borrow a fault code reader from someone, if the ECU light is on, its picked up a sensor error, or a abnormal condition where a sensor is out of range. Try resetting the ecu (unplug it for 30 seconds) and then if the light is on as soon as you turn on the ignition, then its not plugs HT or fuel supply, as the ECU cant detect these faults without the engine running. This mostly leaves only AFM, throttle pot, and 2 temp sensors during a basic sensor check, or the ECU Eprom. A Range Rover dealer will be able to read the codes, if you cant borrow a fault code reader, but its ECU specific, so you average garage with OBD dignostics cant read it. You can test things out with just a test meter, but a fault code reader makes it a whole lot easier. Does the fuel pump start an then stop when you turn on the ignition? If it keeps running, it means the Eprom or microcode in the ECU is corrupted.

Mark


cccscotland

418 posts

285 months

Friday 6th March 2009
quotequote all
Mr Haribo said:
I am lost again ! I have put in 8 new plugs and a new lucas Dab 118 ignition module, a new coil and leads and it still does not start! it does try, and now the Ecu warning light is now on. I took out two plugs today 2 and 4 one was wet the other dry ?????
This is a modded ecu with a bosch air flow meter so im not sure if i can take it to my local car parts factors for a ecu test ?? or is it even the ecu ?
Did you ever fix this? I have a similar problem, and have gone down a similar path to you, so far with no joy!
Cheers

Mr Haribo

Original Poster:

318 posts

220 months

Friday 6th March 2009
quotequote all
At the moment the car is at top cat racing i will let you know more as soon as i do ???

cccscotland

418 posts

285 months

Monday 16th March 2009
quotequote all
cccscotland said:
Mr Haribo said:
I am lost again ! I have put in 8 new plugs and a new lucas Dab 118 ignition module, a new coil and leads and it still does not start! it does try, and now the Ecu warning light is now on. I took out two plugs today 2 and 4 one was wet the other dry ?????
This is a modded ecu with a bosch air flow meter so im not sure if i can take it to my local car parts factors for a ecu test ?? or is it even the ecu ?
Did you ever fix this? I have a similar problem, and have gone down a similar path to you, so far with no joy!
Cheers
Just got my ECU back from the ECU Doctor and she started first time. Hurrah.