Chassis paint decissions
Chassis paint decissions
Author
Discussion

penno

Original Poster:

241 posts

261 months

Friday 9th January 2009
quotequote all
Finally raised the body from the chassis and started to clean the chassis. Chassis condition isn't that bad now the decission is what to paint the chassis with several options after reading posts.

Option 1
use bilt Hamber electrox then cover this with rust buster epoxy mastic 121
http://www.bilthamber.com/electrox-howto.html
http://www.rust.co.uk/epoxy-mastic-more-info.cfm

Option 2
use bilt hamber electrox and cover with Por 15

Option 3
use Por15 complete system
http://www.frost.co.uk/item_Detail.asp?productID=9...

I want to do a belt and braces job because I've decide to keep her and I don't want to do this job for another 10 years. Also would you strip all the powder coat off which is OK or would you paint over it ? I'm keen on using the electrox as the primer seems have very good results


VerySideways

10,272 posts

303 months

Friday 9th January 2009
quotequote all
If the chassis is clean and therefore just has a light surface rust which you have scrubbed clean of loose debris then just use POR-15, without any undercoat/primer/etc.
If you have clean metal (no rust, either new metal or paint or powdercoat) then use metal ready first, but read the instructions carefully!!

I'm putting POR-15 on my chassis in the next few weeks (potentially starting tomorrow) over surface rust (after a good wire brushing with a steel cup brush and power drill!).

POR-15 gets best adhesion on a lightly rusted surface and will last longer than the rest of the chassis!

penno

Original Poster:

241 posts

261 months

Friday 9th January 2009
quotequote all
Heres some pictures panssenger outrigger pretty much down to bare metal 5 mins with anglegrinder/wirebrush attachment. I have a compressor and thinking of purchasing a sandblaster so I can make sure all the areas are clear of rust plus you can never have enough tools. I have reservations about cleaning and painting over rust this is why I'm not 100% convinced about por 15.
After reassurances really

Rear corner


Front


Wishbones


drivers outrigger rear


VerySideways

10,272 posts

303 months

Friday 9th January 2009
quotequote all
I've used POR-15 before on a kit car chassis, the original paint was flaking off and the steel underneath just had mild rust. Took a wire brush to it (by hand) where needed just to take the flakes of paint off, once that was done i went straight on with POR-15 and that was a few years ago and it's still in perfect condition now. You couldn't tell if the POR-15 was done 5 weeks ago or 5 years ago.

The six pack of small tins is £25, i'd be very surprised if you used it and were disappointed.

mongo3528

58 posts

235 months

Friday 9th January 2009
quotequote all
Im in the midst of this job too, got the Por 15 but not ready to apply just yet, but can someone who has previous experience advise me, is it ok to use over the top of original powder coat thats in good condition.. perhaps after just keying the surface with some emery paper? And also how many coats is usual with Por 15 and do they have to be done in quick succession before "curing" begins ? Oh and would you advise i wait until temperatures have increased a bit as i know some paints dont dry if its too cold!?

VerySideways

10,272 posts

303 months

Friday 9th January 2009
quotequote all
mongo3528 said:
Im in the midst of this job too, got the Por 15 but not ready to apply just yet, but can someone who has previous experience advise me, is it ok to use over the top of original powder coat thats in good condition.. perhaps after just keying the surface with some emery paper? And also how many coats is usual with Por 15 and do they have to be done in quick succession before "curing" begins ? Oh and would you advise i wait until temperatures have increased a bit as i know some paints dont dry if its too cold!?
You could go over powder coat if you key the surface first - something like 600 grit is advised i think.
Coats? 1 is often enough if you don't thin it, but if you want to do another you should go over the first coat when it is tacky, which could be anywhere from 1 to 6 hours after application.
POR-15 cures with moisture/humidity so you don't need to worry about the current temperatures from that perspective. It's supposed to rain next week and be a bit warmer (5 to 10 degrees) so this applying the POR-15 this weekend would probably work well...

mongo3528

58 posts

235 months

Friday 9th January 2009
quotequote all
thank for ur advice , im thinking like "penno" , as ive the body raised i wouldnt want to do this job again in a hurry, so if 2 coats gives it slightly better protection, and makes it last longer , im happy to do 2! The worst bit of this job is removing all the old waxoyl.. for all the benefits , its still nasty stuff..

Teetertank

358 posts

218 months

Friday 9th January 2009
quotequote all
mongo3528 said:
Im in the midst of this job too, got the Por 15 but not ready to apply just yet, but can someone who has previous experience advise me, is it ok to use over the top of original powder coat thats in good condition.. perhaps after just keying the surface with some emery paper? And also how many coats is usual with Por 15 and do they have to be done in quick succession before "curing" begins ? Oh and would you advise i wait until temperatures have increased a bit as i know some paints dont dry if its too cold!?
As Sideways says, I have read somewhere that the paint cures counter intuitively- i.e. cures better in cold/damp conditions.

There are detailed instructions on the POR website, and under FAQ - if I remember correctly.

daz the plumber

14,997 posts

262 months

Friday 9th January 2009
quotequote all
ive just purchased some epoxy mastic, its to cold in my garage to do any work but its good stuff ,comes in a two pack and thinners if you want to spray it !

Barreti

6,689 posts

268 months

Friday 9th January 2009
quotequote all
I did exactly what you've got in Option2 in the engine bay last winter, after removing all the old coatings of whatever first. It was very hard work but I doubt I'll need to do it again for a good few years.

I plan to continue with this method for the rest of the chassis. By about 2025 I'll have it all done rofl


BTW: I contacted Bilt Hamber recently about how to prepare and paint the chassis of the Land Rover. This was their reply:
"We would recommend you use our Hydrate 80 product followed by an underbody protection product i.e. anti stone chip coating (maybe 3M) which we do not currently produce."

Food for thought perhaps.

Edited by Barreti on Friday 9th January 17:46

penno

Original Poster:

241 posts

261 months

Monday 23rd March 2009
quotequote all
Thought I'd update the post after I have now finished painting thank god painting forth bridge would be easier and faster.

I went for por15 kit then sprayed shultz stone chip guard then a final coat of Por 15 chassis paint for good measure. I looks good and should stop any rust for a good few years in no rush to repeat this again.

All I have to do is to reassemble easy I will be ready for the summer. Has any body got a good picture of the front wishbone especially the upper as I cannot work out which way round they go or which side and how the upper ball joint align. I thought the drivers side would be the one with the dent for the steering. When I offer this up the ball joint is pointing down. Then to make things interesting the other upper has a dent in it but without the cross brace.





O yer does anybody know of a good way to remove Por15 from skin it gets every wher arms, legs, belly I look like a zebra where it's smudged

VerySideways

10,272 posts

303 months

Monday 23rd March 2009
quotequote all
I'm afraid you may look like a zebra for a month or two...

quattrophenia

1,103 posts

229 months

Monday 23rd March 2009
quotequote all
I saw some instructions (I think the Chimaera pages) about the body lift. Is it just a case of undoing the 22 bolts and raising 6 inches or is the lift a very difficult thing.
I'd be interested in knowing exactly what is involved.

bjarkes

122 posts

215 months

Monday 23rd March 2009
quotequote all
I´am also soon going for POR15, is this correct understood? If there is light rust you go direct on with POR15, no ready metal or degreasing stuff?

Bjarke

Edited by bjarkes on Monday 23 March 19:39

Red V8

873 posts

258 months

Monday 23rd March 2009
quotequote all
bjarkes said:
I´am also soon going for POR15, is this correct understood? If there is light rust you go direct on with POR15, no ready metal or degreasing stuff?

Bjarke

Edited by bjarkes on Monday 23 March 19:39
I used POR15 this time last year... I used metal ready for good measure and also the degreaser... then 2 x coats of POR15 with around 6 hours in between.

If like me you do it over a few weekends, then use cling film to seal the tin, makes opening it a second time a lot easier

1 year on and no sign of chipping or any rust... well pleased.


That Daddy

19,466 posts

252 months

Monday 23rd March 2009
quotequote all
[quote=Barreti I did exactly what you've got in Option2 in the engine bay last winter, after removing all the old coatings of whatever first. It was very hard work but I doubt I'll need to do it again for a good few years.

I plan to continue with this method for the rest of the chassis. By about 2025 I'll have it all done rofl


BTW: I contacted Bilt Hamber recently about how to prepare and paint the chassis of the Land Rover. This was their reply:
"We would recommend you use our Hydrate 80 product followed by an underbody protection product i.e. anti stone chip coating (maybe 3M) which we do not currently produce."

Food for thought perhaps.

Edited by Barreti on Friday 9th January 17:46

[/quote]Ah yes,thanks Ian it was you that gave me the details of the Electrox(Bilt Hamber) primer beer was well pleased with that product and grey POR 15 over the top wink i did the whole front chassis section(upper & lower tubes)and under ladder section/tunnel area right up to the outriggers that i had painted 2 years previous,wish i had done grey all the way though instead i have POR15 in black on my outrigger sections rolleyes

Edited by That Daddy on Monday 23 March 20:44


Edited by That Daddy on Monday 23 March 20:46

penno

Original Poster:

241 posts

261 months

Monday 23rd March 2009
quotequote all
Had a good go at rebuilding tonight got the bottom wishbones assembled and fitted. Then I thought I would tackle the diff bushes. Needless to say this isn't as easy as I expected looking like it's exhaust off,prop and drive shafts ut.

I thought I would be finished by the weekend oh well the weather looks cRp so thats a bonus.

Any one have a picture of the upper front wishbone?

Rum Runner

2,349 posts

248 months

Monday 23rd March 2009
quotequote all
Hammerite Kurust.
Yacht style Epoxy resin
Stonechip rubberished paint on high impact areas
Hammerite smooth, This used to cover over the clear epoxy (mix silver and white for old chassis colour),(White and grey for the later ones).
Wait for a good few months for it properly cure then waxoyle.

You will not see the rust again.

Yacht epoxy is impermeable that is why they use it to treat yachts with osmosis.Its also as hard as nails as its what we used to make anything that is carbon fibre.
You will also find it quite reasonable price wise compared to some of the wonder paints.
95 car ( after a light waxoyle)


98 car



Must say though its a dreadful job.I would not like to guess how many dremel bits i went through,though fantastic for cleaning the welds even after a hospital visit to get some metal out of my eye that the dremel spat at me ( got down the side of the goggles ).
After doing 2 i can guarantee i wont be doing another that's for sure !!!


Edited by Rum Runner on Tuesday 24th March 20:02

That Daddy

19,466 posts

252 months

Monday 23rd March 2009
quotequote all
Tidy job RumRunner wink those cars seldom come up for sale wink

penno

Original Poster:

241 posts

261 months

Tuesday 24th March 2009
quotequote all
Thanks Rumrunner I have a better idea now of the upper wishbone. Mine like yours has the dip and weld on the passenger side where as the drivers side doesn't have the weld but a dip for the steering