wiring a bosch afm
wiring a bosch afm
Author
Discussion

slideways

Original Poster:

4,101 posts

252 months

Wednesday 14th January 2009
quotequote all
Hi All
i would like to fit a bosch airflow meter. can any one tell me if i can use the same loom plug that the standard one uses or do i have to use a different one, if so hows it wired? Will it have to be mapped to work or can it be driven once fitted to somewhere that does mapping also does anyone have a picture of one so i know i have the right one.
Thanks
Rich

Edited by slideways on Wednesday 14th January 19:00

rev-erend

21,624 posts

315 months

Wednesday 14th January 2009
quotequote all
Which AFM model is it and what size of Chim V8 is it ?

slideways

Original Poster:

4,101 posts

252 months

Thursday 15th January 2009
quotequote all
its got PBT-GF30 on the side and has an 83mm internal diameter, its for a 4 ltr
Rich

Edited by slideways on Thursday 15th January 09:27

rev-erend

21,624 posts

315 months

Thursday 15th January 2009
quotequote all
I'll measure mine tonight ..

Does not sound like one of the usual AFMs - they have model numbers like 3AM , 5AM ..

blitzracing

6,422 posts

251 months

Thursday 15th January 2009
quotequote all
The Bosch unit is off the later Sagem system I think, but can be used. It is missing the CO trim pot, so one has to be wired into the loom, plus it definately needs a remap. Bit more about it on the RPI web site:

http://www.v8engines.com/carbs-2.htm

Mark

slideways

Original Poster:

4,101 posts

252 months

Sunday 18th January 2009
quotequote all
blitzracing said:
The Bosch unit is off the later Sagem system I think, but can be used. It is missing the CO trim pot, so one has to be wired into the loom, plus it definately needs a remap. Bit more about it on the RPI web site:

http://www.v8engines.com/carbs-2.htm

Mark
scratchchin just been on RIP's website and mine doesnt look the same as the one in there picture i have a Range rover with the sagem's maf meter and the one i have for the tvr doesnt have a box on the side just a socket unfortunatly im at work for the next 10 days so cant upload a picture of it, i purchased it from a fellow tiv owner as a bosch airflow metre for upgrading the original so maybe its the wrong one?
just found this picture on flea bay looks the same

Edited by slideways on Sunday 18th January 20:48

K4000JB

211 posts

240 months

Sunday 18th January 2009
quotequote all
slideways said:
blitzracing said:
The Bosch unit is off the later Sagem system I think, but can be used. It is missing the CO trim pot, so one has to be wired into the loom, plus it definately needs a remap. Bit more about it on the RPI web site:

http://www.v8engines.com/carbs-2.htm

Mark
scratchchin just been on RIP's website and mine doesnt look the same as the one in there picture i have a Range rover with the sagem's maf meter and the one i have for the tvr doesnt have a box on the side just a socket unfortunatly im at work for the next 10 days so cant upload a picture of it, i purchased it from a fellow tiv owner as a bosch airflow metre for upgrading the original so maybe its the wrong one?
just found this picture on flea bay looks the same

Edited by slideways on Sunday 18th January 20:48
yhm did you get it?

slideways

Original Poster:

4,101 posts

252 months

Sunday 18th January 2009
quotequote all
K4000JB said:
slideways said:
blitzracing said:
The Bosch unit is off the later Sagem system I think, but can be used. It is missing the CO trim pot, so one has to be wired into the loom, plus it definately needs a remap. Bit more about it on the RPI web site:

http://www.v8engines.com/carbs-2.htm

Mark
scratchchin just been on RIP's website and mine doesnt look the same as the one in there picture i have a Range rover with the sagem's maf meter and the one i have for the tvr doesnt have a box on the side just a socket unfortunatly im at work for the next 10 days so cant upload a picture of it, i purchased it from a fellow tiv owner as a bosch airflow metre for upgrading the original so maybe its the wrong one?
just found this picture on flea bay looks the same

Edited by slideways on Sunday 18th January 20:48
yhm did you get it?
Yes i got it thanks, pics and any info would be great did you get yours working ok and is it the same as the one i have?
Rich

K4000JB

211 posts

240 months

Sunday 18th January 2009
quotequote all
i will dig it out of the garage tomorrow and send you some pics as i said in my mail it needs a remap to get running afaik.

slideways

Original Poster:

4,101 posts

252 months

Sunday 18th January 2009
quotequote all
K4000JB said:
i will dig it out of the garage tomorrow and send you some pics as i said in my mail it needs a remap to get running afaik.
thanks i apprieciate that

dhf

1,103 posts

225 months

Sunday 18th January 2009
quotequote all
mine is a hot film airflow meter-bosch thor range rover mhk 100800.it came with a bosch afm 0208218010, air flow meter fitting kit.i will try and post some pics tomorrow.MA supplied and remapped for me.

rev-erend

21,624 posts

315 months

Monday 19th January 2009
quotequote all
slideways said:
its got PBT-GF30 on the side and has an 83mm internal diameter, its for a 4 ltr
Rich

Edited by slideways on Thursday 15th January 09:27
Good news for you - mine has the serial PBT GF30
and it was the big bosch that Mark Adams was fitting as a upgrade to TVR's.. unlike some earlier AFM's - it does not have a co trim screw - so a seperate small trim mechanism was fitted to mine (14 cux).

Not had a change to check wiring much but did find the following :

(Mesh)
^
|
|
Space
Brown
Red
Blue
Blue

Not sure what pins of ecu they go you at moment.

slideways

Original Poster:

4,101 posts

252 months

Monday 19th January 2009
quotequote all
rev-erend said:
slideways said:
its got PBT-GF30 on the side and has an 83mm internal diameter, its for a 4 ltr
Rich

Edited by slideways on Thursday 15th January 09:27
Good news for you - mine has the serial PBT GF30
and it was the big bosch that Mark Adams was fitting as a upgrade to TVR's.. unlike some earlier AFM's - it does not have a co trim screw - so a seperate small trim mechanism was fitted to mine (14 cux).

Not had a change to check wiring much but did find the following :

(Mesh)
^
|
|
Space
Brown
Red
Blue
Blue

Not sure what pins of ecu they go you at moment.
thanks i was begining to think i may have the wrong one
Rich

rev-erend

21,624 posts

315 months

Monday 19th January 2009
quotequote all
Do you need to know where the wires go (ecu pins )

Have you got yourself one of the CO trip pots memtioned by RPI.

blitzracing

6,422 posts

251 months

Monday 19th January 2009
quotequote all
slideways said:
rev-erend said:
slideways said:
its got PBT-GF30 on the side and has an 83mm internal diameter, its for a 4 ltr
Rich

Edited by slideways on Thursday 15th January 09:27
Good news for you - mine has the serial PBT GF30
and it was the big bosch that Mark Adams was fitting as a upgrade to TVR's.. unlike some earlier AFM's - it does not have a co trim screw - so a seperate small trim mechanism was fitted to mine (14 cux).

Not had a change to check wiring much but did find the following :

(Mesh)
^
|
|
Space
Brown
Red
Blue
Blue

Not sure what pins of ecu they go you at moment.
thanks i was begining to think i may have the wrong one
Rich
Those wire colours are not the same on the standard loom, so there must be some conversion inside the loom somewhere. There are 4 basic connections only, 12 volts, ground, airflow out and trim resistor and this is just a variable resistor to ground. This is why you can bodge it with a trim resistor between two wires as per the RPI site.

These are the standard wire colours

Red/black. Ground

Blue/Green Air flow signal- should be .2-.7 volts (no air flow). Tick over on the 3.9 is about 1.7 volts

Brown Orange +12v

Blue/red CO trim value.


Mark

K4000JB

211 posts

240 months

Monday 19th January 2009
quotequote all
slideways said:
K4000JB said:
i will dig it out of the garage tomorrow and send you some pics as i said in my mail it needs a remap to get running afaik.
thanks i apprieciate that
ok i have taken the pictures send me your email address and i will mail you them

slideways

Original Poster:

4,101 posts

252 months

Monday 19th January 2009
quotequote all
K4000JB said:
slideways said:
K4000JB said:
i will dig it out of the garage tomorrow and send you some pics as i said in my mail it needs a remap to get running afaik.
thanks i apprieciate that
ok i have taken the pictures send me your email address and i will mail you them
YHM sir
Rich

slideways

Original Poster:

4,101 posts

252 months

Monday 19th January 2009
quotequote all
rev-erend said:
Do you need to know where the wires go (ecu pins )

Have you got yourself one of the CO trip pots memtioned by RPI.
i have'nt got one yet but i would be interested in any more info on your setup,
thanks to every one who has sent pics and info