Graunchy crunchy driveline noise.... guess the cause
Graunchy crunchy driveline noise.... guess the cause
Author
Discussion

Pupp

Original Poster:

13,040 posts

303 months

Friday 16th January 2009
quotequote all
Just limped home with said graunchy crunchy noise, and very slight occasional vibration (as something was obviously breaking up), after just one sharp bang after pulling from a junction. Nothing visible on the roadside, car still driving (sloooooooowly and smoooooooothly as not too far from home) with no obvious loss of fluids, drive or overheating of anything.... Seemed to be from rear drivers side

...I'm guessing driveshaft CV joint(s). Any others...? Prolly be tomorrow before I get chance to investigate properly so all suggestions welcome (within reason)

Oh, while I'm at it, big thanks the to numerous impatient idiots on the A6116 who were tailgating an obviously sick car displaying hazards when there was loads of time/space to just overtake... censored

Edited by Pupp on Friday 16th January 13:28

chimalsu

279 posts

269 months

Friday 16th January 2009
quotequote all
has the diff run dry

chimalsu

279 posts

269 months

Friday 16th January 2009
quotequote all
just to add i also had a wheel bearing dissintergrate on another car that made same sort of noises jack car up and check for play on wheels

schmokin1

1,223 posts

243 months

Friday 16th January 2009
quotequote all
I would guess driveshaft CV or diff, prop I would have thought would snap a joint or be too bad to drive at all once gone ping.

Tailgaters redcard don't get me started. It's amazing how many drivers there are out there who don't know how to overtake but think it's OK to stop everyone else doing it by driving right up one's chuff!!

spend

12,581 posts

282 months

Friday 16th January 2009
quotequote all
Diff calamity sounds just like that IME wink

Pupp

Original Poster:

13,040 posts

303 months

Friday 16th January 2009
quotequote all
spend said:
Diff calamity sounds just like that IME wink
Cheers!

Hopefully not, was a fair bit of 'clicketty click' going on too and I've never heard a diff do that. But you never know.

I'm assuming the wishbones have to come out or at least be dropped/swung somehow to get the shaft out? Anyone able to point me to a walk-through anywhere please? Might as well gen up and then find it's the diff... smile

spend

12,581 posts

282 months

Friday 16th January 2009
quotequote all
6 cap heads at either end, there is sliding joint that gives enough leeway to jiggle them out, with the wheel off IIRC.

Pupp

Original Poster:

13,040 posts

303 months

Friday 16th January 2009
quotequote all
spend said:
6 cap heads at either end, there is sliding joint that gives enough leeway to jiggle them out, with the wheel off IIRC.
Sounds far too easy... biggrin

spend

12,581 posts

282 months

Friday 16th January 2009
quotequote all
First 1 degree on each cap head is most critical, you then quickly learn to loosen off in sequence with a ball end so the d/s doesn't fall off & you cant access the last one hehe If I explained it you'd do different - it becomes apparent when you struggle. IIRC I found it easier to remove the wheel end with the wheel loaded, then support the shaft in a cup to do the diff end, adjust the holder to get the angle you need for best access (but you know me & my inexhaustible supply of scrap wood hehe)

Pupp

Original Poster:

13,040 posts

303 months

Friday 16th January 2009
quotequote all
Thanks. That's useful to know... makes sense

spend

12,581 posts

282 months

Friday 16th January 2009
quotequote all
Avoiding FRUSTRATIONirked is key when working in those awkward places, its definitely a pack of fags each side job in my b;ack book of estimating metrics hehe

schmokin1

1,223 posts

243 months

Friday 16th January 2009
quotequote all
spend said:
Avoiding FRUSTRATIONirked is key when working in those awkward places, its definitely a pack of fags each side job in my b;ack book of estimating metrics hehe
know all about that, it's just taken me all day to get the rear copper brake pipes off, reflared, and on again. If I smoked it would have been 3 packs biggrin

good luck with the graunch!

Torque Matters

3,606 posts

263 months

Friday 16th January 2009
quotequote all
I'll put my money on CV's.

If you do get tempted to remove the rear upright for better access remember to only undo the two bolts on the bottom wishbone so it doesn't mess with your camber settings.

Good luck!

GreenV8S

31,027 posts

315 months

Friday 16th January 2009
quotequote all
How many gears did you try? If it's in the box then you would expect the symptoms to change as you change gear. If it's downstream of there then changing gear won't make any difference.

Pupp

Original Poster:

13,040 posts

303 months

Friday 16th January 2009
quotequote all
Gears are all present and correct; the noises were road speed, worse pulling away etc... 90% sure it's a joint. Will dive in tomorrow or Sunday.

rev-erend

21,624 posts

315 months

Friday 16th January 2009
quotequote all
CV joint..

Numties would not even overtake a bicycle.. just moan how slow he was ..

steve-V8s

2,924 posts

279 months

Friday 16th January 2009
quotequote all
If the Diff bushes re a bit soggy and you give the Diff a reason to twist in the mounting. The drive shafts are then not correctly aligned and complain quite loudly. More of a clonk clonk sound though.

spend

12,581 posts

282 months

Saturday 17th January 2009
quotequote all
From Steves cue it is well worth the time whilst you are down there to study the effects of ride height on your driveshaft alignment. It's quite easy to see how much extra stress is put on the joints at small deflections. The next time you see an inordinately low car you will then be wondering how long their D/s will last wink

GreenV8S

31,027 posts

315 months

Saturday 17th January 2009
quotequote all
spend said:
The next time you see an inordinately low car you will then be wondering how long their D/s will last wink
... then look how much roll-induced camber they are getting and wonder what this is doing to the handling. smile

spend

12,581 posts

282 months

Saturday 17th January 2009
quotequote all
Maybe we should form our own "ACOF" club Peter? wink

Anti Chav Old Farts Club hehe