Weak handbrake
Weak handbrake
Author
Discussion

speedychimp

Original Poster:

17 posts

215 months

Sunday 18th January 2009
quotequote all
I have a T reg 400 I noticed when I bought the car from fernhurst that the handbrake would only go on two clicks and would not hold if parkerd on a hill they said this is common with all Chimaera's and that you stick it in gear and use two hands to pull it up further for the third click which would do the job. However yesterday I coldn't release the button so I had to call the AA and they unscrewed the end to release the spring for the button which did the job but cost me £86 for the aa to turn up, why fernhurts didn't tell me to do this in the first place!! Anyway AA were concerned that you had to use two hands and brute force to get the hand brake engaged also you should be able to gain access to the handbrake workings?!? by pulling out the money tray (apprantly there should be a screw under this which lifts off but couldn't locate this)

Any other owners have this problem with the Handbrake? I can't understand why you need to be popeye to engage the handbrake, not convinced with what fernhurst are telling me

HRG

72,863 posts

270 months

Sunday 18th January 2009
quotequote all
On my Griff it's four or five clicks. You can get more mechanical leverage if the adjuster (in the OSR wheel arch) is backed off a little.

I always put the handbrake on with my foot on the footbrake so that the lever is just keeping what pressure is already there applied.

grumbledoak

32,571 posts

264 months

Sunday 18th January 2009
quotequote all
They are all like that. Just leave her in 1st. That stops the brakes seizing, too.

spend

12,581 posts

282 months

Sunday 18th January 2009
quotequote all
I'm sorry but that is all complete bks!

The brake mechanism requires play in the handbrake cable, as soon as the caliper adjuster begins to seize people just keep tightening the cable, which exacerbates the problem.

Stick new pads in, making sure you wind back & free up the adjuster. If it doesn't move freely get your calipers overhauled / exchanged / replaced. Stretching cables, breaking levers / buttons is just plain stupidity IMHO. Claiming TVR h/brakes never work is nearly as bad, they were fine for cars nearly twice the weight, even without the upgraded pad/disc area...

In short, if PROPERLY serviced they work "." .....

jsr

1,155 posts

281 months

Sunday 18th January 2009
quotequote all
On mine, 2 clicks is easy to apply and ok for level ground. The 3rd click requires more force and will happily hold the car on an incline. It helps greatly to apply the foot brake before apply or releasing the hand brake

T_Pot

2,542 posts

228 months

Sunday 18th January 2009
quotequote all
jsr said:
It helps greatly to apply the foot brake before apply or releasing the hand brake
top tip that does work a lot

scotty_d

6,795 posts

225 months

Sunday 18th January 2009
quotequote all
spend said:
I'm sorry but that is all complete bks!

The brake mechanism requires play in the handbrake cable, as soon as the caliper adjuster begins to seize people just keep tightening the cable, which exacerbates the problem.

Stick new pads in, making sure you wind back & free up the adjuster. If it doesn't move freely get your calipers overhauled / exchanged / replaced. Stretching cables, breaking levers / buttons is just plain stupidity IMHO. Claiming TVR h/brakes never work is nearly as bad, they were fine for cars nearly twice the weight, even without the upgraded pad/disc area...

In short, if PROPERLY serviced they work "." .....
yes Agree i have had a rubbish hand brake last summer and it was to job this winter new cable, pads and i have overhauled the calipers with new pistons and seals and the hand brake is as good as new now no problem's at all

2 sMoKiN bArReLs

32,044 posts

266 months

Sunday 18th January 2009
quotequote all
Never ever use the handbrake. biggrin

speedychimp

Original Poster:

17 posts

215 months

Sunday 18th January 2009
quotequote all
has anyones handbrake stuck on i.e pushing the release buttons does not release? The AA guy replaced the spring with a smaller one seems to working fine at the moment, bit apprehensive to go to 3 clicks though