Im an idiot, but still need help
Im an idiot, but still need help
Author
Discussion

jaybee747

Original Poster:

141 posts

252 months

Sunday 18th January 2009
quotequote all
After having the car fixed, (twice on bodywork) finally got a chance to have a good run out. The car thought differently. To put it bluntly it ran like a bag of s***e. putting it down to a misfire, I purchased all the usual bits, Cap, Arm, Leads, etc. All in vain. I then tried all plugs & leads individually, all OK. Then I discovered the stupid bit, the vacuum-advance valve had come away from the distributor!

Reffitted the item after removing plastic cover on the dizzy a relocating it on the peg. Then time for a road test. After warming up, I took it on the M1 for a bit of a thrash. All OK till I came off the exit. Running just as bad as before. Managed to get home and check the afore mentioned problem and all seems OK. Don't know what to check for next as all items have been replaced. It seemed fine when cold, (no shunting, missing) but when warm the problem re-occured.

Any help would be appreciated.

Jaybee

pwd95

8,459 posts

269 months

Sunday 18th January 2009
quotequote all
Knackered temp sensor? The ECU thinks the engine is still cold & carries on delivering an enriched fuel mixture. Too rich fuel mixture causies the engine to missfire when warm? Correct me if I'm wrong chaps.

Edited by pwd95 on Sunday 18th January 20:00

jaybee747

Original Poster:

141 posts

252 months

Sunday 18th January 2009
quotequote all
If the mixture was too rich it would "blacken" the plugs wouldn't it? Removed all plugs and the colour looks fine,(A dark Beige brown).

I did a search on this issue and another member had the same thing happen to him. He just refitted the vac valve and all was OK, but can't find any other reasons for mine not to.

pwd95

8,459 posts

269 months

Sunday 18th January 2009
quotequote all
scratchchin Is it consistenty fine when cold & missing when warm?

jaybee747

Original Poster:

141 posts

252 months

Sunday 18th January 2009
quotequote all
Don't really have the answer to that as I only found the problem this afternoon. The initial problem, (before I found the loose part) worsened as it warmed but as said this was before I discovered the loose vacuum valve. The car, this afternoon, when cold, ran sweet as a nut but then tried to stall, (and did) when slowing for juctions, turns,etc. Just can't think that it is something serious as the car was faultless, and has been for sometime before this. I use the car regularly but when it was in for repairs it wasn't run regular, (3 months).

Del 203

12,728 posts

280 months

Monday 19th January 2009
quotequote all
Bad connection on the LT side of coil? Possibly a broken wire inside the loom or inside the insulation itself which is butting up & making good connection cold but not when hot wink


Believe me it can happen frown


You can have hours of fun diagnosing/finding it & pcensoreding people off on the phone talking about it !!! Eh Spendy wink

Wildfire

9,951 posts

283 months

Monday 19th January 2009
quotequote all
Have you replaced the coil?

When they are on the way out they tend to cause bad misfiring and rough running when hot, and fine when cold.

BeastMaster

443 posts

218 months

Monday 19th January 2009
quotequote all
Could also be the ignition amplifier. Mine gave problems when hot causing missing, but never missed a beat when cold. Probably electrical and the part breaking down when hot. You could try an ice pack on parts like the coil etc to cool it down and see if the problem goes away for a time.

blujay10

583 posts

261 months

Monday 19th January 2009
quotequote all
100 amp fuse is blamed for lots of things so maybe its on its way out/corroded? Worth a look just to rule it out and cheap to replace! Found underneath near the starter motor.

STE VR

501 posts

237 months

Monday 19th January 2009
quotequote all
I had murder with mine after i was detailing the engine..she was running superb and then very similar symptoms to yours. I went through absolute hell to get it sorted and most of it my fault. Turned out after a very long story to be the AFM even though i had replaced it (new one was faulty). Try disconnecting the AFM plug when the symptoms arise and see if she runs better (it won't run perfect and don't run it for more than a couple of minutes). I did bench test mine and it was fine but breaking down under load/fitted to car.

HTH

Steve

sploosh

822 posts

239 months

Monday 19th January 2009
quotequote all
If you've not run the car for a few months try some fresh fuel, it does go "off".


jaybee747

Original Poster:

141 posts

252 months

Wednesday 21st January 2009
quotequote all
Hi Fellas.

Sorry about the delay in responding, (Work issues for 2 days.)
Just to let you all know, the problem, it seems, has disappeared. But before I tried another cold run-to warm run I thought I'd try a little process of elimination. So I put the old rotor arm on. I was going to try other items also but it runs fine hot and cold now. When I get another chance I'm going to refit the new one to see for definate if this was the problem. If it is I'm going to be a little more choosy about where and who I source my parts from.

Thanks to everyone for responding, it was getting a little "worrysome" but all's well in t'end.

Jaybee

woohoo

VerySideways

10,272 posts

303 months

Wednesday 21st January 2009
quotequote all
I made the mistake of using a Halfords dizzy cap and rotor a few years back on a Chim 4.0, a week later the rotor arm shattered. I had kept the original worn Land Rover genuine stuff in the boot, stuck it back on and the car ran noticeably better biggrin

jaybee747

Original Poster:

141 posts

252 months

Wednesday 21st January 2009
quotequote all
confused

I was informed that Unipart were original spec for Landrover but then told Lucas. Also I seem to find that Intermotor parts are not favourable either.
It's a bit of a minefield.

Jaybee