camshaft change
camshaft change
Author
Discussion

barrybike

Original Poster:

33 posts

274 months

Monday 19th January 2009
quotequote all
i have a 4.0 hc chimera and need to change the cam and followers, can it be changed in situ without taking the engine out, and any recommendations for a suitable cam with a bit lower grunt and not so much top end. my rover vitesse would pull in 5th from 1000 revs as smooth as silk. any help appreciated

steve-V8s

2,924 posts

279 months

Monday 19th January 2009
quotequote all
May be better to think about changing the ECU rather than the Cam. That way you may get smooth low down and still have the top end

paulathome

686 posts

249 months

Monday 19th January 2009
quotequote all
Yes the cam can be changed with the engine in situ.
Only have to remove intake and trumpet base then you can get at the valley gasket.
Once this is off all will be revealed.
It would be a good idea to fit new cam chain and sprocket together with all new rocker gear while your
at it.
As for cam choice I'm sure there will be a heated debate as to which you should fit.
Cheers.
Paul.

Al 450

1,390 posts

252 months

Monday 19th January 2009
quotequote all
I had a Piper 218 fitted, seems mega torquey at low revs now, as my builder put it " do you want a pub cam or a driving cam? " bhp vs torque...

daz the plumber

14,997 posts

262 months

Monday 19th January 2009
quotequote all
remember, your chip as been programed to your cam and engine set up, so any changes will end up costing you even more cash .!

daz the plumber

14,997 posts

262 months

Monday 19th January 2009
quotequote all
thats not what the specialist say !are you saying if i removed the standard cam and fitted a a high lift cam such as a tornado the car would not need re chipping !

Chimjunkie

2,879 posts

242 months

Monday 19th January 2009
quotequote all
Quinny said:
Bit more to it than that Paul.

The inlet manifold rocker covers, water pump and front cover and pulleys all have to come offyes

But you're right about the heated debatehehe

personaly I'd go for an ABC123hehe

Edited by Quinny on Monday 19th January 19:10
And to get the front cover off the exhaust y-piece needs to come off which also means the rear arb needs dropping hehe


spend

12,581 posts

282 months

Monday 19th January 2009
quotequote all
Quinny said:
The chipAir Flow Meter will compensate for minor changes
Suggested rephrasing? wink

That Daddy

19,464 posts

252 months

Monday 19th January 2009
quotequote all
daz the plumber said:
remember, your chip as been programed to your cam and engine set up, so any changes will end up costing you even more cash .!
Well its funny you should say that Daz because my brother borrowed my HC ECU for a couple of days in the spring(intermittant loss of power,long story)and noticed no differance what so ever(and he is a fussy bugger for drivability)even the dreaded lurch was unchanged,his car is a non HC and my HC ECU is cosha even down to the white sticky label on the chip and the marker pen 4.0HC on the case,just a heads up really wink and Barrybike O/P the HC cam can easily be improved upon tractabity wise its quite severe for road use/suberb driving infact some might say the 4.0HC is over cammed standard,in saying that i will be sticking with this kind of profile in the future i like motors with bite hehe not really into linear power delivery myself.

Edited by That Daddy on Monday 19th January 23:08

daz the plumber

14,997 posts

262 months

Monday 19th January 2009
quotequote all
think you will find tvr did not pafect there fueling, just got it some where near !

Edited by daz the plumber on Monday 19th January 23:08

That Daddy

19,464 posts

252 months

Monday 19th January 2009
quotequote all
daz the plumber said:
think you will find tvr did not pafect there fueling, just got it some where near !

Edited by daz the plumber on Monday 19th January 23:08
thumbup agreed

quattrophenia

1,103 posts

229 months

Tuesday 20th January 2009
quotequote all
OK lets get to the nitty gritty. How much for a standard or upgraded cam replacement??

Barkychoc

7,848 posts

235 months

Tuesday 20th January 2009
quotequote all
I think you'll find whatever cam you put in there it will run better than one with no lobes on it! biggrin

spend

12,581 posts

282 months

Tuesday 20th January 2009
quotequote all
Barkychoc said:
I think you'll find whatever cam you put in there it will run better than one with no lobes on it! biggrin
With the ecu adding the same amount of fuel to each pot in the bank, and worn lobes at the back, no wonder it gets confused by the lambda sensors readings and runs lumpy is it? Note how often MA has said he aborts mapping sessions because the cam doesn't pass go. wink

I assume £1k is fitted, DIY could be <£400. I know where there is a good wildish (256) used cam + followers due to upgrade (to mech) if you want a cheap one.

lewis_sharman

5,958 posts

222 months

Tuesday 20th January 2009
quotequote all
I'm looking to change the cam soon (100,000 miles on the original)

After reading previous posts i hear a lot about the stealth and MC1 cam, but i am still undescided whether i want to go for a wilder cam. As i understand it, the low and midrange torque is compromised. Is this right or have i got the wrong end of the stick?

What does everyone have on here, and what do you see as the positives and negatives to each cam.

One last thing, what parts should i change as the engine is partially stripped down, and where can i source all the parts??

spend

12,581 posts

282 months

Tuesday 20th January 2009
quotequote all
If you are contemplating an ecu upgrade with mapped ignition a wilder cam is a no-brainer IMHO wink What kind of cam you need depends on how you want the car to drive???? Most supply cams off the shelf so will try & sell you their 'best fit', much better to talk to people like Rob Rob. or Jamie and ask them based upon as much detail about your engine & what you want out of it, as they have many std & custom options available.

That Daddy

19,464 posts

252 months

Tuesday 20th January 2009
quotequote all
Barkychoc said:
I think you'll find whatever cam you put in there it will run better than one with no lobes on it! biggrin
Very true laugh

thegman

1,928 posts

235 months

Tuesday 20th January 2009
quotequote all
I have an MC1. Very, very smooth, with plenty of low down torque. Very linear and progressive but drops off significantly after about 5400. I would say an excellent choice if the majority of your driving is town and motorway, rather than country/track.

spend

12,581 posts

282 months

Tuesday 20th January 2009
quotequote all
thegman said:
..drops off significantly after about 5400...
Cam is a major limitation in how much your RV8 will rev, rather than any mechanical / electronic deficiency..

Pau1

316 posts

236 months

Tuesday 20th January 2009
quotequote all
What are the symptoms of a worn cam exactly?