Later TVR wheels on a wedge.

[Transmitter Man]

Have any of you fitted later model TVR wheels to your wedge.

Wheel and tyre sizes plus pic's would be appreciated.

I am considering a change from scuffed 15" split rims.

Thanks.

Phil

[peaktorque]

Transmitter Man said:

Have any of you fitted later model TVR wheels to your wedge.

Wheel and tyre sizes plus pic's would be appreciated.

I am considering a change from scuffed 15" split rims.

Thanks.

Phil

As far as I understand, Cerbera/Tuscan etc. wheels will fit, but the PDC is slightly different, which means that nuts don't seat properly in the recesses and are at constant risk of becoming loose.

Which is a shame because the 16" Cerbera 'Saturn' wheels do suit the Wedge and I have just seen a set of four go on e-bay for £16!

Someone on here has done it, but I am unsure if the wheels were re drilled to match the Wedge stud pattern.

[TVRleigh_BBWR]

other option would be to fit new hub's to take the new style wheels. you can fit new style callipers then also.

[Waynester]

I had 17" Azev alloys on my 1st 400. Looked ok, but tbh i prefer the original Oz's.

[BHardy]

I have fitted 17inch borbets on my 400se (had them on my 350i as well before I changed it for a 400), but favorite would be 16inch OZ's

[barrington]

i had 17s on my 350 if you look at my profile i have a pic and i now have 17inch oz for my 400

[deetes]

Cerb wheels on mine.

Not too bling

[tr7andtvr]

I have Audi RSR wheels on my car. 245/45/17

[peaktorque]

deetes said:

Cerb wheels on mine.

Not too bling

I like.

Have you modded the wheels to suit the stud pattern?

I am very keen to change my wheels for these

[deetes]

[quote=peaktorque
Have you modded the wheels to suit the stud pattern?

I am very keen to change my wheels for these
[/quote]

Eccentric washer dood dahs available from most wheel shops.

[peaktorque]

deetes said:

[quote=peaktorque
Have you modded the wheels to suit the stud pattern?

I am very keen to change my wheels for these

Eccentric washer dood dahs available from most wheel shops.

Thanks!

Just what I needed to hear

Suppose I'm going to have to get me a set of them now

[red tasmin]

Cerbera 16" OZ on mine too!

[Transmitter Man]

Thanks for the feedback guys.

Dave, do you have a pic of the 17" OZ's on the 400?

Was the stud pattern and wheel offset correct?

Wheel width and tyre sizes please.

How is handling?

Same questions for the Cerb wheels Allan.

I do like the idea of getting a one-piece rim rather than splits.

Anyone running Enkie's?

Once again thanks.

Phil

[James MK]

I want to upgrade mine to 16". What's the ride like with lower tyres? Bit hard, or is the difference that noticeable?

[barrington]

not fitted the 17s yet but pistolar has had 17s on his 400 for many years tyre sizes are 235/40/17 they have 10mm spacers the stud pattern is ford/merc 5 stud (have to fit 17s as i have tuscan s brakes)

[deetes]

Rides fine with the 16" wheels as the tyres aren't too low. Just wish I could drive it at the mo, but it's in bits just now awaiting a new cam etc. Those d@m chocolat cams!!!!!!!!

[Transmitter Man]

Another PH'er Alan, sent me a image of Jeff Statham's yellow racer with Image wheels this together with another shot of the same car I found on one of the Wedge sites:





I'll be contacting him to find out sizes.

Look nice.

Phil

[James MK]

deetes said:

Rides fine with the 16" wheels as the tyres aren't too low. Just wish I could drive it at the mo, but it's in bits just now awaiting a new cam etc. Those d@m chocolat cams!!!!!!!!

Mine (being a v6) started off with 14" rims, on 15" at the moment so for me to go to 16" I'll be down to 50 series tyres. Got to decide what kind of wheels I want first, that will probably keep me busy for the next year looking at everyone elses!

Hope you get that cam fixed in time for spring!

[barrington]

i have a set of 400 oz on classifieds another option

[Transmitter Man]

Dave,

Sizes, with or without tyres?

I'm looking for 17's with wider that stock SEAC tyres.

Phil