Fuel regulator
Fuel regulator
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Tuesday 27th January 2009
quotequote all
Im thinking of ditching my rising rate fuel regulator 1:7 and trying an adjustable 1:1 regulator can anyone recommend a make or model?
scratchchin I remember someone on here saying you can buy them quite cheap on ebay

Thanks


118

819 posts

261 months

Tuesday 27th January 2009
quotequote all
Try this one, I am assured it is reliable and good value.
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&am...

Meatball

Original Poster:

1,638 posts

241 months

Tuesday 27th January 2009
quotequote all
[redacted]

clive f

7,259 posts

264 months

Tuesday 27th January 2009
quotequote all
try these guys, I had one on my 5lt griff and cost about £75.
give them a bell and they will sort you out with thecorrect one.

http://www.fuelsystem.co.uk/regulators.htm

GreenV8S

31,027 posts

315 months

Tuesday 27th January 2009
quotequote all
Meatball said:
Im thinking of ditching my rising rate fuel regulator 1:7
Do you already have the fuel rail adapter to let you use a remote regulator (e.g. FSE)? If so, you can use whatever you like. But without the adapter you need to get one that fits the fuel rail which basically means RR 3.9 classic from any RV8 specialist.

blitzracing

6,422 posts

251 months

Wednesday 28th January 2009
quotequote all
Demon tweeks did a Range Rover fuel rail adaptor for external fuel regulators. I have one of the £40 fuel regulators off ebay, and its pretty well made and has a gauge as well. Its a complete waste of time fitting a regulator without one, it all becomes guess work.



daz the plumber

14,997 posts

262 months

Wednesday 28th January 2009
quotequote all
rpi sell the complete kit with guage made by fse you can get the same thing from demon tweaks slightly cheaper.the fse malsappi 1:1 was recommended by v8 developments .i remove the guage and fit the plug supplied .mine is set at 37psi with the vac pipe removed . the fse 1:1 works the same as the the standard one on the rail but it can be tweaked

spend

12,581 posts

282 months

Wednesday 28th January 2009
quotequote all
I've never really understood this bling gauge under the bonnet thing? Gauge is only any good when you can see it? I just plug mine up when I'm not using the gauge lasts longer.. car weighs less... less things to go wrong (leak).. wink

Ballistic Banana

14,706 posts

298 months

Wednesday 28th January 2009
quotequote all
I agree, and dont they come saying they shouldnt be left on? well i think the RPI ones do IIRC but I am going doolally atm so god only knowsnuts

BB

spend

12,581 posts

282 months

Wednesday 28th January 2009
quotequote all
ATM? Only At the Moment BB? eviltongue out

GreenV8S

31,027 posts

315 months

Wednesday 28th January 2009
quotequote all
blitzracing said:
its pretty well made
I think the important things are how accurately it regulates the pressure under changing conditions, and whether this behaviour drifts over time. Those aren't really things you can tell just by seeing ow solid looking and shiny it is.

blitzracing

6,422 posts

251 months

Wednesday 28th January 2009
quotequote all
Fair comment, I have had to re adjust it once as the adjustment thread is pretty course, and the lock nut can come loose quite easily. Thread lock is the cure for that. As for leaving he gauge on, its instant diagnosis of the fuel system if the cars not running quite right, plus it will tell you if the spring in the unit does weaken over time. Ive not noticed a perfomance reduction with all that extra weight !!

K4000JB

211 posts

240 months

Wednesday 28th January 2009
quotequote all
i fitted a weber 3.0bar reg which caused a few problems because it was set to 3.25bar(standard hotwire injectors only work up to 3.1 bar) so everytime i put my foot down the pressure was to great causing some of the injectors to stick shut (tricky to pinpoint due to different injectors being affected each time). which brings me to my next question how do people get the fse rising rate reg to work on standard injectors or do they change them at the same time?

GreenV8S

31,027 posts

315 months

Wednesday 28th January 2009
quotequote all
K4000JB said:
set to 3.25bar ... pressure was to great causing some of the injectors to stick shut
I recall Mark Adams saying that could be an issue with the disc type injectors, but I wasn't aware that it would become an issue at such a low pressure.

K4000JB

211 posts

240 months

Wednesday 28th January 2009
quotequote all
GreenV8S said:
K4000JB said:
set to 3.25bar ... pressure was to great causing some of the injectors to stick shut
I recall Mark Adams saying that could be an issue with the disc type injectors, but I wasn't aware that it would become an issue at such a low pressure.
hi peter
i had this happen and disregarded the fuel pressure due to the reg being a sealed preset(@3.0bar) weber one, it through up misfiring problems. it was only after the car was left over night and the misfire had gone that i looked at the maximum fuel pressure finding it higher than the max 3.1 bar of the hotwire injectors i adjusted it and the problem was solved.
it just maybe my injectors are old and need changing.

spend

12,581 posts

282 months

Wednesday 28th January 2009
quotequote all
Hmmmm?, I was under the impression that one of the main advantages of the Lucas injectors was there ability to perform adequately (some have claimed even better) under raised pressures confused

K4000JB

211 posts

240 months

Wednesday 28th January 2009
quotequote all
spend said:
Hmmmm?, I was under the impression that one of the main advantages of the Lucas injectors was there ability to perform adequately (some have claimed even better) under raised pressures confused
hi dave
the standard reg has a 2.5bar max pressure (iirc) thats why i opted for a 3bar one to allow for more fuel if needed



p.s you will have mail soon thumbup

spend

12,581 posts

282 months

Wednesday 28th January 2009
quotequote all
Wasn't a specific comment at your problem James, I'm not sure there is any reason to change from Lucas even if you want bigger flowing injectors (I think MikeV & Pasco regretted changing to Bosch in hindsight?). We've certainly seen a couple of strong cars close on 350bhp with original injectors and raised fuel pressure. Obviously it is not easy to make direct comparisons unless you have access to the fuelling in the ECU wink

Meatball

Original Poster:

1,638 posts

241 months

Wednesday 28th January 2009
quotequote all
I think BBs right about leaving the gauge on, mine had a sticker on it saying its only for setting up and not as a permanent fitting.

Some good info on here tbh i dont know how my rising rate reg is fixed to the fuel rail i`ll take a look at the weekend to see if its a simple swap as green says.

Ive been talking to the guy who supplied my afm and he suggested trying a little more fuel with my set up.



GreenV8S

31,027 posts

315 months

Wednesday 28th January 2009
quotequote all
K4000JB said:
GreenV8S said:
K4000JB said:
set to 3.25bar ... pressure was to great causing some of the injectors to stick shut
I recall Mark Adams saying that could be an issue with the disc type injectors, but I wasn't aware that it would become an issue at such a low pressure.
hi peter
i had this happen and disregarded the fuel pressure due to the reg being a sealed preset(@3.0bar) weber one, it through up misfiring problems. it was only after the car was left over night and the misfire had gone that i looked at the maximum fuel pressure finding it higher than the max 3.1 bar of the hotwire injectors i adjusted it and the problem was solved.
it just maybe my injectors are old and need changing.
You've prompted me to go back to dig out Mark's original comments, in this thread in 2005:

Mark Adams said:
Lucas injectors are a disc type design - that is they have a disc that sits over a metering hole in a plate. The disc is lifted off the hole by the solenoid to allow fuel to flow. The more you increase the fuel pressure, the more difficult it becomes to lift the disc off the hole. There comes a point at around 3.3 Bar where the fuel flow actually starts to drop as you increase the pressure.

Futhermore, increasing the fuel pressure actually changes the battery voltage corrections required for the injector. This requires the corresponding rework of the ECU software including cranking tables. So it is not just a simple matter of increase the pressure no worries, unless you have no understanding of the implications.
It doesn't seem as if 3.1 bar would be high enough to cause the problem but may not be far off, and in any case as you say there may have been other faults contributing to the problem.