Oil Change
Oil Change
Author
Discussion

BeastMaster

Original Poster:

443 posts

218 months

Friday 30th January 2009
quotequote all
Hi Guys. Planning a service this weekend and am very confident in everything that needs to be done except oil and filter change. Not sure about the oil pump priming - have been told that providing I,m quick should not have this problem. Engine is pre serpentine and runs perfect with good oil pressure. Should I expect to prime the pump, and get the additional gasket now to remove the pump cover ? Many thanks - Beastmaster

rev-erend

21,624 posts

315 months

Friday 30th January 2009
quotequote all
I've done my pre serp hunderds of times and never needed to reprime it..

Just make sure you dont leave it draining for hours.. and also fill the oil filter with oil before fitting it.. it absorbs into the paper element anyway.. and wear gloves smile

BeastMaster

Original Poster:

443 posts

218 months

Friday 30th January 2009
quotequote all
Thanks rev-erend - put my mind at rest, this issue was putting me off doing the job myself. Beastmaster

spend

12,581 posts

282 months

Friday 30th January 2009
quotequote all
Fill the oil filter before you start, they literally can take hours to fill... Each time it appears full, 10-30 mins later you will be able to top up.... until it is full. I reckon that gives you a lot better safety margin against priming issues. Downside is you have to spin it on very quickly and its a fair bit heavier hehe

That has always seemed a more important step to me even than the 'method/theory' of squirting oil up the middle of the spin-on if you have priming problems.

Barkychoc

7,848 posts

235 months

Friday 30th January 2009
quotequote all
I had a discussion with Pete Humphries about this a while back and he suggested it was better to have an empty filter - so that the pump has no resistance against it on the output side when initially pulling oil from the sump.
I think I'm with him on this one, though I think we could discuss this for and aginst till the cows come home.

Edited by Barkychoc on Friday 30th January 10:28

spend

12,581 posts

282 months

Friday 30th January 2009
quotequote all
I would certainly advocate pumping oil into the pump side (PRV) in preference to the engine side (middle of spin-on) if you have priming problems wink

Must admit I have never felt confident in the priming by having oil for the pump to work against (there was an old thread where I raised this - which gets misquoted fairly regularly by DorninMeinerSeite)

Do Note: both Peter & I have slightly different 'challenges' as we both run oil coolers & remote stats. Don't know about Peter, but I do drain down my cooler at oil changes, as well as the accumulator... There is potential for an awful lot of air and quite a delay from firing to oil delivery in those situations. I guess that is why we both use drill pumps to pre-oil?

I see no reason why the cheap drill pumps could not be used on std engines, just suck from the timing cover & dump it in the rocker cover oil filler. Some pipe and connector to stick in one of the M20 serp blanking plugs / pre-serp tappings must be cheaper & easier than the dizzy drill priming tools?

That Daddy

19,464 posts

252 months

Friday 30th January 2009
quotequote all
spend said:
I would certainly advocate pumping oil into the pump side (PRV) in preference to the engine side (middle of spin-on) if you have priming problems wink

Must admit I have never felt confident in the priming by having oil for the pump to work against (there was an old thread where I raised this - which gets misquoted fairly regularly by DorninMeinerSeite)

Do Note: both Peter & I have slightly different 'challenges' as we both run oil coolers & remote stats. Don't know about Peter, but I do drain down my cooler at oil changes, as well as the accumulator... There is potential for an awful lot of air and quite a delay from firing to oil delivery in those situations. I guess that is why we both use drill pumps to pre-oil?

I see no reason why the cheap drill pumps could not be used on std engines, just suck from the timing cover & dump it in the rocker cover oil filler. Some pipe and connector to stick in one of the M20 serp blanking plugs / pre-serp tappings must be cheaper & easier than the dizzy drill priming tools?
Bloody hell Spend,bet you love oil&filter change time on your car frown still its worth having the fuel accumulator system and oil cooler fitted as you know,i wont take changing my oil & filter simplicity for granted next time wink
Of course you dont need to answer this Spend.

Edited by That Daddy on Friday 30th January 12:11