Discussion
Hi there
Got a real problem with no6 spark plug. Just can't get it in. Looks to be cross threaded although I was never that heavy-handed. So it is probably minor damage to the thread but a major PITA for me.
Now looking to take the head off to repair. TVR shop quote over £100 for a head gasket set. Seems a bit steep. Anybody got any good recommendations for a more reasonable set.
Any other advice on the head removal appreciated as well.
I probably should remove both heads seing as I will be that far in, and do a top end overhaul. What do you think?
Rgds
Phil
Got a real problem with no6 spark plug. Just can't get it in. Looks to be cross threaded although I was never that heavy-handed. So it is probably minor damage to the thread but a major PITA for me.
Now looking to take the head off to repair. TVR shop quote over £100 for a head gasket set. Seems a bit steep. Anybody got any good recommendations for a more reasonable set.
Any other advice on the head removal appreciated as well.
I probably should remove both heads seing as I will be that far in, and do a top end overhaul. What do you think?
Rgds
Phil
Something like this might be worth a try first?
http://cgi.ebay.co.uk/Spark-Plug-Thread-Chaser-Spa...
http://cgi.ebay.co.uk/Spark-Plug-Thread-Chaser-Spa...
Mikey V (AJPGriff) does HG's at good prices, but full sets of composite are quite expensive everywhere.
Plug chasers don't go all the way through from the inside, you will need am M18x1.25 bolt to fine the last bit (that starts the plug). Just done one
If its bad then its a helicoil job though.
From the outside plug chasers can make the situation worse IMHO
Getting the heads off gives you quite a lot of opportunity to see / fettle what you have
Plug chasers don't go all the way through from the inside, you will need am M18x1.25 bolt to fine the last bit (that starts the plug). Just done one
If its bad then its a helicoil job though.From the outside plug chasers can make the situation worse IMHO

Getting the heads off gives you quite a lot of opportunity to see / fettle what you have

Cheers Lads
Got a thread chaser, but S
t scared I ( As Dave says) make the situation a whole lot worse.As I say I believe the damage to be very slight, but enough to cause me all this hassle.
So it's head off to repair. Just as well it's winter, eh?
Is getting the head off relatively straightforward??
Cheers
Phil
Got a thread chaser, but S
t scared I ( As Dave says) make the situation a whole lot worse.As I say I believe the damage to be very slight, but enough to cause me all this hassle.So it's head off to repair. Just as well it's winter, eh?
Is getting the head off relatively straightforward??
Cheers
Phil
If you've only done it by hand without applying huge amounts of effort then you haven't done much damage and at most it will only have affected the first one or two turns of thread. I wouldn't be looking to retap or take the heads off to repair.
I don't know how much experience you have, but you need somebody who is used to doing this sort of thing to get the plug lined up correctly, find the start of the thread and keep the plug straight as the thread engages. Once it's in the first turn the rest will be a doddle. Depending what state the thread is in you might find you need to repair the first couple of damaged threads, which you should be able to do by feeding in a tapered thread. (An old plug with the bottom of the thread filed down would do the job nicely.)
If you don't fancy doing this yourself (or have tried and decided you need expert help) I'd suggest dropping into your local garage and offering one of the fitters £20 to drop by on his way home. I'd only expect it to take a couple of minutes to get the thread started, but make sure you're talking to an experienced fitter and not just a tyre/exhaust monkey.
I don't know how much experience you have, but you need somebody who is used to doing this sort of thing to get the plug lined up correctly, find the start of the thread and keep the plug straight as the thread engages. Once it's in the first turn the rest will be a doddle. Depending what state the thread is in you might find you need to repair the first couple of damaged threads, which you should be able to do by feeding in a tapered thread. (An old plug with the bottom of the thread filed down would do the job nicely.)
If you don't fancy doing this yourself (or have tried and decided you need expert help) I'd suggest dropping into your local garage and offering one of the fitters £20 to drop by on his way home. I'd only expect it to take a couple of minutes to get the thread started, but make sure you're talking to an experienced fitter and not just a tyre/exhaust monkey.
The head bolts can really take some cracking! particularly the later stretch bolts ( I hate them with a vengeance
). You need a really long bar & strong sockets... Rest is pretty straightforward (manifold removal pah!
).
Get decent gaskets, plenty of places sell them at better prices than mentioned, V8D, MikeyV, V8tuner, even TVRPower I would have thought... They aren't cheap but they should be less than mentioned ~ unless they've recently been hit by exch rate like a few US parts??
Its all fairly simple if you aren't touching the cam, just clean / inspect maybe lap valves... There is lots of scope for tuning and don't discount the opportunity to put in a cam ~ it would be sad to have to strip everything again soon... At least make sure TDC is aligned correctly on the pointer whilst the heads are off
). You need a really long bar & strong sockets... Rest is pretty straightforward (manifold removal pah!
).Get decent gaskets, plenty of places sell them at better prices than mentioned, V8D, MikeyV, V8tuner, even TVRPower I would have thought... They aren't cheap but they should be less than mentioned ~ unless they've recently been hit by exch rate like a few US parts??
Its all fairly simple if you aren't touching the cam, just clean / inspect maybe lap valves... There is lots of scope for tuning and don't discount the opportunity to put in a cam ~ it would be sad to have to strip everything again soon... At least make sure TDC is aligned correctly on the pointer whilst the heads are off

How are you getting on with the crossed plug Phil?
Happened to me too - same plug as well (No. 6) and I got hold of something like these:
http://www.back-tap.com/
but made by Snap-On
If you want I'll whack em in the post to you if you promise to return em!
Might be worth a try before pulling the head...
PM if you're interested.
Ryan
Hi again
Worked out what the problem was.
Had a spark plug removal tool since I was 17 ( long time ago!!).
Have always used this. However, TVRs being what they are, the tool is too long, but only for plug No 6, and if you offer it up to the plug hole, the exhaust manifold gets in the way. This is only because of the length of my plug remover. No 6 plug is at completely the wrong angle. Thankfully now sorted. Need to remember to use a shorter removal tool.
Cheers Phil
Worked out what the problem was.
Had a spark plug removal tool since I was 17 ( long time ago!!).
Have always used this. However, TVRs being what they are, the tool is too long, but only for plug No 6, and if you offer it up to the plug hole, the exhaust manifold gets in the way. This is only because of the length of my plug remover. No 6 plug is at completely the wrong angle. Thankfully now sorted. Need to remember to use a shorter removal tool.
Cheers Phil
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



