450 Chimaera Snag list
450 Chimaera Snag list
Author
Discussion

Chemlock

Original Poster:

23 posts

215 months

Sunday 1st February 2009
quotequote all
Hi,

Sorry if all these things have been address in other threads, I did do a search but didn't come up with anything that match the exact issues.

So I got a 450 Chimaera yesterday and have a few niggles that I will want to address over the coming months. These are.

1. The rubber seal at the front edge of the driver’s side window is perished and jamming the window on the way up. It still goes up but I've seen snails move faster. I would imagine this is fairly easy to replace and source but don't know where to start. I've seen this (http://www.racetechdirect.co.uk/product-subsection-detail.asp?MakeID=2&ModelID=2&CATID=9&SUBCATID=67&PROID=342) but wonder if that is the strip across the bottom inside of the window rather than the rubber that runs up the front edge gutter. Any ideas or costs?

2. The seal in the corner of the windscreen is a little loose. A couple of people have said mastic it or something but that seems a little criminal. Is there a better way of getting that stuck down and replaces? Costs?

3. The driver’s side door mirror suffers from droop during long journeys. I start out seeing behind me and end up with a nice view of tarmac shooting past. Can the joint be tightened with the door cover off or does this mean that something’s gone wrong inside the mirror joint? Costs?

4. The power steering makes a slight breathing noise when turning? Is this normal or should I get it looked into? Again, anyone got experience of cost to replace?

That's all so generally I'm really happy especially when it's singing at me and things get a little blurry. The only other thing I've noticed is that at low speed in high gears the car gets a little lurchy and makes a slight knocking noise between momentum moving the car and the engine taking up the slack. I'm fairly sure this is down to me not changing down, mainly due to not being used to all that torque.

dogbucket

1,256 posts

232 months

Sunday 1st February 2009
quotequote all
I repaired my windscreen rubber using a polyurethane sealant/adhesive, ie Sikaflex or Soudaflex 40FC being 2 brands. I wouldnt use a silicone type sealer as they dont stick as well.

The lurching sounds like what is commonly referred to as shunting, and seems to effect some cars worse than others. iirc it is the ECUs inability to correctly fuel at low revs due to the hotter than normal cams used in our engines. Any wear/slack in the drivetrain or diff bushes as the car gets older makes it seem worse and cause knocking noises. It is certainly something you either get used to, or can be cured with aftermarket ECUs. However ensuring the ignition system is in good shape like HT leads/coil/dizzy cap/rotor can go someway to reduce it.

Edited by dogbucket on Sunday 1st February 13:53

Chemlock

Original Poster:

23 posts

215 months

Sunday 1st February 2009
quotequote all
That bit on shunting is really interesting as the car has a Mark Adams chip and magacor(sorry for any spelling mess up) leads. Do you think it might need a little tweaking? It is something I can easily live with as changing down cures it and I really should stop being so lazy as to be doing 30mph in 5th.

dogbucket

1,256 posts

232 months

Sunday 1st February 2009
quotequote all
I think the problem is at low revs the programmed map has little effect as the system is trying to adjust everything on the fly to keep the mixture correct. But it gets confused by the air flow due to the cam and runs out of adjustment and the mixture goes too weak. Hence having a good ignition system to try and ignite what is there. Thats about all I know and may or may not be totally correct!

Have a look for posts on here by Blitzracing who has done alot investigation.

Edited by dogbucket on Sunday 1st February 14:16

GreenV8S

31,027 posts

315 months

Sunday 1st February 2009
quotequote all
Shunting varies from car to car and even from day to day. It's very common for this to happen below 1500 rpm; if you still have it at 2000 rpm there's probably something wrong. In general, you should try to keep it above the rev range where this happens. Although the engine has enough torque to drive round very easily at tickover, it's not good for the engine to labour it and also shows up these shunting problems.

Chemlock

Original Poster:

23 posts

215 months

Sunday 1st February 2009
quotequote all
Thanks for that. I'll change my driving style (style might be an over statement).

Now all I need is a mirror that doesn't drop and some solution to the sticky window issue. By the way does anyone else audible signs that the power steering is working?

900T-R

20,406 posts

288 months

Sunday 1st February 2009
quotequote all
I find I can pull extremely smoothly in any gear from basically idle upwards (very tasty rebuilt engine), but tend to get a bit of driveline shunt on the overrun/trailing throttle below 1.500 rpm (which is easily avoided) - probably a combination of a bit of play in the driveline (it does have 112K miles on it hehe) and the 'free' rpm on the overrun normally dropping to 1,500, then whatever basic idle is at (around a thou' on mine) a sec or two later. I think the latter is a characteristic of the car rather than the engine/ignition/fuel mapping.

Edited by 900T-R on Sunday 1st February 17:49

GreenV8S

31,027 posts

315 months

Sunday 1st February 2009
quotequote all
Chemlock said:
Thanks for that. I'll change my driving style (style might be an over statement).

Now all I need is a mirror that doesn't drop
You're not going to like this I'm afraid. frown

The mirror is attached to the door by a threaded boss on the door, the mirror is attached to a threaded sleeve which screws on to the boss. If the sleeve not done up tight it can allow the mirror mounting to 'unscrew' from the door. It may be possible to tighten it by carefully turning the mirror body clockwise as if you were trying to screw it into the door.

The mirror isn't attached directly to the sleeve; that would be far too easy. There is a spindly casting that pushes over the sleeve and is secured with a grub screw. If the grub screw is loose then the mirror will be free to rotate and you won't be able to tighten it. In this case you have to take the whole mirror off, tighten the grub screw and then screw it back onto the boss. The position of the sleeve relative to the mirror body determines where the mirror sits when the sleeve comes up tight and of course you can't tell that until you've fitted it, so lots of trial and error involved here.

It gets worse though. That spindly casting is designed to break off in a collision. As a result it's designed to be quite weak. They can break spontaneously, and it's easy to damage or break them while you're trying to sort the mirror out. If the mount breaks the mirror falls off, dangles on the wires and can damage the door. Sod's law says it will hold together just long enough to get up to 70 mph on the motorway before breaking for maximum effect.

So, you may be able to fix the problem just by carefully turning the body of the mirror to tighten the mount, but you may find it doesn't work and in any case you need to be extremely careful.

Al 450

1,390 posts

252 months

Sunday 1st February 2009
quotequote all
My power steering has always moaned and groaned when the wheel is turned. Looking back at the history the pump was changed under warranty after a complaint about it being noisy then as well.

I've heard that sometimes the filter mesh in the reservoir gets clogged. Might be worth changing some of the fluid? p.s. you'll probably also find that the power steering hose from the reservoir is a bit knackered. This is normal and can be tolerated as long as it isn't leaking.

spend

12,581 posts

282 months

Sunday 1st February 2009
quotequote all
Isn't there a 'fold in' position on those mirrors (its been so long... yes)? If the mirror wasn't fastened in the correct orientation that might cause it to continually turn?

Chemlock

Original Poster:

23 posts

215 months

Sunday 1st February 2009
quotequote all
Thanks all. I knew I could rely on some solid answers. Being a naturally inquisitive person I did try turning the mirror clockwise earlier today as it seemed to tight things up what way. Unfortunately I then got to drive 20 miles with a view the sky and snow (which was fun) as it got stuck in the wrong angle. I managed to eventually get the courage to manhandle it back into the original position but again it's but exactly solid and needs re-adjusting every 20 miles or so. This is a real pain because it's the drivers window that goes up at the speed of a glacier melting.

As the words grub, boss and screw immediately spring other thoughts to mind (especially when used together) rather than car parts I'm feeling I might be best served taking into a local mech.

Power steering - Thanks that's what other people have said. It's only just audible but then again when the car is running most things are only just audible. I'll live with it and see where it takes me.

Anyone got any window ideas?

Anyone got any opinions on where is best to get it looked at. I'm fairly near Austec, Fernhurst and Racing Green. Anyone know of any positives or horror stories. Austec seem very friendly but maybe a little specialised for tinkering with a wing mirror and maybe replacing the window rubbers.

siwebster

417 posts

224 months

Monday 2nd February 2009
quotequote all
Hi, I've just had problems with my mirror in the last fortnight - and also had a slow window. My mirror actually sheared off, which meant removing it completely, which in turn meant I had to take the door panels out from the inside in order to get to everything. It sounds a bit daunting but is fairly straightforward, but as well as removing the mirror it gave me the opportunity to grease the window mechanism and lubricate the motor, etc. Window works much smoother, faster and quieter now. Going to do the same to the passenger side at some point soon.

Having been able to have a good luck at the mirror, everyone so far is right, the grub screw that holds the tripod mount to the car is more than likely loose causing your mirror to drop down. Tightening it up appears to be extremely difficult though as there's not really room to get an allen key in, but I'm sure someone will enlighten us with a bit of ingenuity that these forums are famous for...

As for shunting at low speeds, I find that removing the stepper motor and giving it a good clean and spray with wd40 helps a lot. Only a 10 minute job too.

Hope this helps a bit,

Si

siwebster

417 posts

224 months

Monday 2nd February 2009
quotequote all
Forgot to add - is the knocking noise you're getting sound like it's from the front or the middle/back?

If it's coming from the middle/rear, or you can feel it through the gear lever or under your left elbow, it's more than likely the top diff bush. Unfortunately this is not an easy or cheap job, sorry...

Edited by siwebster on Monday 2nd February 09:55

Bodmin

596 posts

229 months

Tuesday 3rd February 2009
quotequote all
Agree with GreenV8S on the mirror problem. You will probably find it is the grub screw which is coming undone but it is awkward to get at. I managed to slightly tighten mine by hacksawing an allen key to the right length but could never get it quite tight enough & as GreenV8S has pointed out the mirror metal frame is quite brittle.

The slow operating window usually turns out to be the felt guide strip on the runners, it can be changed but is a bit fiddly & you need patience. However there are two methods that are worth trying first;

Apply silicone spray on the felt/runners & then operate the window up & down a few times. This quite often works but you need to reapply the silicone every so often.

Lubricate the motor. If you remove the door speaker you can see through the aperture the motor(silver cylinder). On the upper side of the motor you will see a clear plastic stopper plug. By using a small screwdriver you can prise out the plug & then squirt WD40 in the hole. If you can reach the window switch try operating the motor as you spray the WD40(HSE; mind your fingers near the runners) in & this will help lubricate it. Because a lot of TVRs stand dormant for days/weeks between use, especially at this time of year, the motor internals start to corrode & sometimes you get the scenario where the window will stick at the very bottom or very top of its travel.

The PAS pumps can become noisy but very rarely fail. If the steering suddenly goes heavy when the noise occurs it may be there is some air in the system or the pressure relief valve is sticking open. If there is no noticeable differance then just keep an ears to it, if it gets noticebly nosier then it needs to be looked at.

The shunting you are describing seems to affect all the Rover V8 engined Tivs fitted with cats. I think it has something to do with how the ECU interperates the information from the Lambda sensors at low revs for fuelling. The remapping usually smooths some of this out but if there is wear in the driveline it amplifies it.

At the end of the day all the models seem to have their little foybels but the main thing is you seem to be enjoing the experiance drivingthumbup

Bodders

Chemlock

Original Poster:

23 posts

215 months

Tuesday 3rd February 2009
quotequote all
Cheers for that Bodmin,

I took it for a spin today and had to re-adjust the mirror every 10 minutes. The only positive to this is that the window seems to have recovered slightly. It does appear that the felt guide along the front of the door frame is perished and as the window rises loose parts of this jam/slow the movement. I've found the part to replace it at racetechdirect (Part No U0399).

I've tried turning the mirror clockwise and have managed to jam it into a position that half holds it. It pretty much spins freely though so I'm going to put my money on something being broken inside. I did notice that he electric adjust has now stopped working.

All this kind of points to me having to take the door card off and have a look at what lies beneath. I can then WD40 the window motor, attempt to replace the window felt and find out what's up with the mirror. My only worry with this is I don't want to be left with a hanging mirror or having to take it off while awaiting a replacement part. It's kind of handy for getting into the car. If the mirror spins freely but is still attached should I invest in a mirror toad stool, just in case?

And another thing! What is the knack of fuelling these things (apart from often) every pump I've used keeps clicking off as if the car is full (I'm guessing due to bubbles/froth in the tank pipe. I've tried all sorts of angles and the only way I've found of doing it is pressing the hose nearly vertically in (right up against the boot lid) and holding the trigger at about 40%. It's cold slow work in this weather. I would have thought for a car this thirsty they would make feeding it's addiction easier. Any tricks?

Al 450

1,390 posts

252 months

Tuesday 3rd February 2009
quotequote all
I find that if you get it all the way in from behind then twist it clockwise 90 degrees then it usually works.

As for the car? Waaaheyyy.........

I'll get my coat.

getmecoat

Chemlock

Original Poster:

23 posts

215 months

Tuesday 3rd February 2009
quotequote all
I'll try it but I don't think she will let me go out for a drive afterwards.

2 sMoKiN bArReLs

32,045 posts

266 months

Tuesday 3rd February 2009
quotequote all
I find filling with the pump t'other side of the tank seems to make it easier. (gawd knows why)

siwebster

417 posts

224 months

Wednesday 4th February 2009
quotequote all
Chemlock said:
Hi,

makes a slight knocking noise between momentum moving the car and the engine taking up the slack.
Did you manage to work out whether this was coming from the front or the back?

Had what sounds to be the same on my car and it got gradually worse, definitely coming from the mid rear of the car, I could feel it under the transmission tunnel. It would happen if the car lurched, but I could also make it do when standing still and bringing the clutch up to bite when in gear (engine running). Turned out to be the top differential mounting bush. Got it replaced with a poly bush, but not cheap and easy...

Chemlock

Original Poster:

23 posts

215 months

Wednesday 4th February 2009
quotequote all
Will try the biting point thing. It is only at 1500rpm (had a play this morning) and I think it's just lurch from the engine not running smoothly.
Someone has mentioned it could be the cams that were put in aligned with the tornado chip all leading to a car that's not set up for low rev driving.