Chim 400 overfuelling and down on power
Discussion
Had my Chim for a year now- its a (As far as a I know) standard 400 serpentine with cats and 100K on it..
Have noticed when driving it that it seems to start to run out of go at 4.5K-5K, and and above 5K on wide open throttle the engine note changes and it starts popping and banging like nothing else..
Had suspected that it may not be putting quite as many horses as it should be, and peak power 'felt around 1000rpm or so lower than it should be..
Anyway, took it to the rolling road and it seems to confirm this... peak power is between 190-197 BHP at about 5100-5200 rpm, with peak torque around 230 lb ft at around 3400 rpm, but overall a v.wide flat torque cure between 2000 and 4500 rpm. Air Fuel ration hovered between 10 and 12, averaging 11 but dipping to 10.5 at some points..
Anyway-appreciate thoughts on the above and potential resolutions etc.. ..one thing that has crossed my mind is potential cam wear limiting valve opening times and airflow causing the transient AFR to go rich..
..not sure what happens to the AFR at steady-state but I 'suspect' it may be adjusted to give a within tolerance lamdba (had no issues with the MOT last March which I believe does not test transients..)
Anyway, thoughts appreciated-
Have noticed when driving it that it seems to start to run out of go at 4.5K-5K, and and above 5K on wide open throttle the engine note changes and it starts popping and banging like nothing else..
Had suspected that it may not be putting quite as many horses as it should be, and peak power 'felt around 1000rpm or so lower than it should be..
Anyway, took it to the rolling road and it seems to confirm this... peak power is between 190-197 BHP at about 5100-5200 rpm, with peak torque around 230 lb ft at around 3400 rpm, but overall a v.wide flat torque cure between 2000 and 4500 rpm. Air Fuel ration hovered between 10 and 12, averaging 11 but dipping to 10.5 at some points..
Anyway-appreciate thoughts on the above and potential resolutions etc.. ..one thing that has crossed my mind is potential cam wear limiting valve opening times and airflow causing the transient AFR to go rich..
..not sure what happens to the AFR at steady-state but I 'suspect' it may be adjusted to give a within tolerance lamdba (had no issues with the MOT last March which I believe does not test transients..)
Anyway, thoughts appreciated-
The lambda control is only up to 3400 rpm, or less than 3/4 throttle, and should keep the mixture around 14.5:1. The ECU can cope with sensors and fuel pressure being out by some considerable margin, and it simply adjusts the injector timing to bring the fuel back into lambda range. I had the screw come loose on my fuel presure regulator, leading to 50 psi pressure (it should be 37 psi) and the ECU still controled the mixture correctly, but it snatched badly at low speed as the ECU battled with too much fuel, and performance was very poor, but it still went through an MOT perfectly. Once the ECU goes open loop it just relies on the fixed fuel map, and various sensor inputs and the mixture should be around 12.5:1 for best power. Im assuming your fixed load was above 3400 rpm or 3/4 throttle, so if to much fuel is going in you can suspect as most likely a faulty engine temperature sensor, faulty AFM, or excess fuel pressure. If its never been correct, it may have the wrong fuel map in the ECU. Also worth your while plugging in a fault code reader, as the ECU may be in fall back mode, but on many TVR's the ECU warning conditions do not bring the light on (This is down to the fuel chip programming).
Mark
Mark
Ok- thanks for the feedback and thoughts all..
The rolling road was done a full throttle, so I don't have any AFR readings for less than 3/4 throttle/3400 rpm- however at open throttle it was much less than 12.5:1 - (between 10 and 12:1) - with this in mind when it goes in for its next check-up (couple of weeks) I'll get ECU diagnostics done- sensors checks etc-
In the event that it is the cam- what sort of outlay should I be looking at to get it, together with associated rockers etc replaced, and does anyone have any thoughts on what the choice re cams (this is for a non-HC 400)
Ta..
The rolling road was done a full throttle, so I don't have any AFR readings for less than 3/4 throttle/3400 rpm- however at open throttle it was much less than 12.5:1 - (between 10 and 12:1) - with this in mind when it goes in for its next check-up (couple of weeks) I'll get ECU diagnostics done- sensors checks etc-
In the event that it is the cam- what sort of outlay should I be looking at to get it, together with associated rockers etc replaced, and does anyone have any thoughts on what the choice re cams (this is for a non-HC 400)
Ta..
Hmm- standard RR cam?- didn't think of that one-
I guess the steps (in order) to diagnosis are:
- ECU fault codes?
- any sensors out?
- visual camshaft inspection for wear?
-..ermmm..
I would be doing the any camshafts myself so not sure there's any mileage inspecting the cam myself-
In the event it is the cam- anyone have any suggestions re replacement cams?
I guess the steps (in order) to diagnosis are:
- ECU fault codes?
- any sensors out?
- visual camshaft inspection for wear?
-..ermmm..
I would be doing the any camshafts myself so not sure there's any mileage inspecting the cam myself-
In the event it is the cam- anyone have any suggestions re replacement cams?
I think Green could be on to something here. Ive been looking at a 5lt engine that really down on power, its just flat and wont rev as it should. Looking at the lambda response on this engine (at less than 3400 rpm), the switching speeds on the probes is around 1- 1.5 seconds, whilst all the other engines Ive looked at, is around .5- .75 of a second. These speeds do vary with engine RPM, but the 5ltr is noticably slower. Both probes have been changed, but the fuel trim is still very slugish. If the mixture / burn do significantly change with cam lobe wear this might be an easy visable result to measure to test for cam wear. It just takes a test meter across the white and black wires as they go into the lambda extension cables behing the fuel rail....HiAsAKite, I can send you a video clip of a correct tickover response if you want to test your engines response times.
Mark
Mark
Edited by blitzracing on Monday 2nd February 21:11
Slow lambda response is one of the signs of a failing (blocked) sensor, I suppose it might also be caused by the engine being a long way away from lambda 1. A worn cam usually means that the affected cylinders don't breath as well so they get less air at high revs and run rich; the other cylinders get more than their fair share of the air and run lean. Since the lambda sensors measure oxygen, the lean cylinder[s] cause it to show a lean signal even though other cylinders may be running rich. I suppose it's possible that this could cause the lambda feedback loop to behave strangely, but proving that it does might be tricky.
Turned out to be a worn cam,
2 of the lobes were virtually round, 3 of the others were showing definite wear and maybe one looked the way it should look-
This means that on one cylinder there was practially no air going in, and one of the others virtually no air was coming out...
...begars belief that the engine ran at all and didn't blow something to be honest..., let alone put out 190-197 BHP...
Now have a new cam fitted, and the engine is much smoother, more tractable at low revs, and will run up and down the rev range happier.. have to say I didn't really realise quite how much I was compensating for it before, but the car is no much easier to drive smoothly- plus it pulls a lot solidly and feels much quicker....
On paper, now putting 250lb ft across most the rev range and 218 BHP (flywheel- 180@wheels), and will happily rev to 6K without appearing lose power or start backfiring..
Edited to add- will try post some pics of the old cam at some point.. its about to be come a rather heavy garage wall ornament
2 of the lobes were virtually round, 3 of the others were showing definite wear and maybe one looked the way it should look-
This means that on one cylinder there was practially no air going in, and one of the others virtually no air was coming out...
...begars belief that the engine ran at all and didn't blow something to be honest..., let alone put out 190-197 BHP...
Now have a new cam fitted, and the engine is much smoother, more tractable at low revs, and will run up and down the rev range happier.. have to say I didn't really realise quite how much I was compensating for it before, but the car is no much easier to drive smoothly- plus it pulls a lot solidly and feels much quicker....
On paper, now putting 250lb ft across most the rev range and 218 BHP (flywheel- 180@wheels), and will happily rev to 6K without appearing lose power or start backfiring..
Edited to add- will try post some pics of the old cam at some point.. its about to be come a rather heavy garage wall ornament
Edited by HiAsAKite on Wednesday 15th April 20:35
Edited by HiAsAKite on Wednesday 15th April 20:35
For those of you interested to see what a worn camshaft looks like- I've finally got some pics..
The third lobe in this picture, is supposed to be as big as the fourth lobe- the forth lobe you can see still has most of its profile- the third lobe has a lsight 'bulge' where the lobe used to be

This is the camshaft held the other way round (ie photo from the other end)
You can see that the 4th cam has a prounced lobe. The third lobe should look similar, but yet again barely bulges..

3 of the other lobes were also worn, but not as 'nearly circular' as these..
The new cam has complete transformed the car
The third lobe in this picture, is supposed to be as big as the fourth lobe- the forth lobe you can see still has most of its profile- the third lobe has a lsight 'bulge' where the lobe used to be

This is the camshaft held the other way round (ie photo from the other end)
You can see that the 4th cam has a prounced lobe. The third lobe should look similar, but yet again barely bulges..

3 of the other lobes were also worn, but not as 'nearly circular' as these..
The new cam has complete transformed the car

Edited by HiAsAKite on Saturday 2nd May 19:38
Gassing Station | Chimaera | Top of Page | What's New | My Stuff




