Loud Tappet/Bearing Noise followed by spulttering
Loud Tappet/Bearing Noise followed by spulttering
Author
Discussion

KarlR

Original Poster:

262 posts

241 months

Sunday 1st February 2009
quotequote all
Took the car out for a run tonight, and noticed when I pulled up at a roundabout either load tappet noise or possibly bearing noise. After pulling away, the car was spluttering and hesitant as if there was a fuel problem. When I got home, the noise had gone and seemed to be running ok again. Was this a sticky lifter - any clues?? It was very cold at the time and snowing, although never had this problem before. Recently had a new camshaft, so dont think it is related to this.

Many thanks,

Karl.

spend

12,581 posts

282 months

Sunday 1st February 2009
quotequote all
Brakes frozen on?

KarlR

Original Poster:

262 posts

241 months

Sunday 1st February 2009
quotequote all
No brakes were fine, had driven about 30 miles up to this point. When I pulled up (Stopped), the engine sounded very noisy, similar to before I had the Camshaft changed. Then spluttering, as if it was going to cut out. Start it again tomorrow again and see if its any different - just wondered if a sticky lifter could cause the sluttering?, as this is what it sounded like.. if its the same, I think itll be heading for the garage!

Thanks,

Karl.

KarlR

Original Poster:

262 posts

241 months

Sunday 1st February 2009
quotequote all
err.. spluttering I mean..

rev-erend

21,624 posts

315 months

Sunday 1st February 2009
quotequote all
I would check the exhaust manifold gaskets at the head first .. only takes a few mins to check..

daz the plumber

14,997 posts

262 months

Sunday 1st February 2009
quotequote all
i had my cam changed and lifters , they said the ports where the lifters fit are slightly oval . im been trying to get to the bottom of my clatter for ages , its on tick over and when the engine is on load , once its free reving it goes like a train .is your air filter clean ?


Edited by daz the plumber on Sunday 1st February 22:56

KarlR

Original Poster:

262 posts

241 months

Sunday 1st February 2009
quotequote all
The manifold gaskets were replaced only three or four months ago, so hopefully not that - air filter, possible - but would it cause the noise?

Talkwrench

910 posts

264 months

Monday 2nd February 2009
quotequote all
Hows the oil pressure and oil level?
Sounds a bit like the lifters don't have an adequate oil supply. If they dont operate properly, they will clatter due to excess clearance and the engine will stutter and misfire as the valves don't open properly.

rev-erend

21,624 posts

315 months

Monday 2nd February 2009
quotequote all
KarlR said:
The manifold gaskets were replaced only three or four months ago, so hopefully not that - air filter, possible - but would it cause the noise?
It's only takes 5 mons to check / tighten the lot .. it's a common problem.

spend

12,581 posts

282 months

Monday 2nd February 2009
quotequote all
If you are convinced it was a rattle, might be worth checking the trumpets are still in their holes. If one comes loose it can partially block a port, chances of it bouncing back in perfectly are probably nil. They often escape and what with this brass ball weather ??? Can't see it being sticky lifter if you've had a new cam, most reports of this are after they've got fairly gummed up after lots of use with not so nice oil....

GreenV8S

31,027 posts

315 months

Monday 2nd February 2009
quotequote all
The only thing I can think of which would produce a temporary mechanical knocking and misfire would be a valve sticking, but that's not very likely and also not very likely to clear itself so quickly - and also has a significant risk of valve/piston impact on these engines. So even the most likely explanations in my view are not very likely - is it possible you simply had a brief misfire and noises caused by fuel burning in the exhaust?

KarlR

Original Poster:

262 posts

241 months

Monday 2nd February 2009
quotequote all
Ok thanks for the replies - shall investigate further..