Engine Rebuild - Anyone have/know a workshop in Bristol?
Discussion
Well, it's finally beaten me!
The lumpy running and vibration hasn't been cured by:
Plugs
Leads
Cap
Rotor
Fuel Pressure Regulator
AFM
Lambdas
and a whole load of 'checking of various electrical connections'
I hoped it might be injectors but recently I've revised my thinking seeing as it happens under engine braking too - ie when no/little fuel is entering the engine so must be mechanical...
The car still goes like a Stabbed Rat but after 15 mins on the motorway it feels horrible and the vibration is accompanied by a ticking - similar to a tappet/cam noise but not as 'dull' and from the near side of the engine.
The penny dropped when I read a post about loose liners and cracked blocks from a previous post entitled "Oh Oh - Cracked Liner Time" - excerpt below....
2) Liner slipped - this is were the liner is not properly located at the bottom of the block and eventually moves up and down with the piston ..
symptoms - sounds like a tappet or cam shaft is on its way out.. running with it like this for long would be a good way to scrap a block.
So that leaves me with one option - pull the whole engine down to parts and inspect the block with a view to getting top hat liners fitted.
I want to do this myself over a few month period or so. I don't have any facilities (I park on the street!) so I'm asking if anyone knows of a workshop to rent or similar in Bristol. I simply cannot afford to get it done by a pro so may as well read up on as much info as I can get my hands on and jump in at the deep end!
I've heard they are 'fairly simple engines' and have a basic knowledge of how the whole thing works so time to get my hands dirty!
Any advice/hints/tips gratefully received.
Correct me people if I am wrong but my understanding is a slipped liner is accompanied by overheating as the water jacket is compromised.
I'm have thought a cam is more likely to be the culprit - could be worth stripping the cam & followers out first before tearing the entire engine down.
I'm have thought a cam is more likely to be the culprit - could be worth stripping the cam & followers out first before tearing the entire engine down.
I would also advise that you are not too hasty in ripping the engine apart until you are sure about what is wrong. The fact it still goes like a 'stabbed rat' and is not overheating would make me think again. Try Webbs in Nailsea and get them to take a look. I've always found them friendly and knowledgeable and it could save you doing the wrong thing.
Sounds similar to some of the noises and vibration I was experiencing. Car went well enough but there were some odd vibrations, a ticking noise from the o/s and occasional strange behaviour from the engine - lumpy running, occasional stalls funny tickover.
Turned out to be very simple.
The ticking was a leaking exhaust gasket - diagnosed in about 5 seconds by a mechanic with a stethoscope
All the other problems turned out to be engine mount related. One mount had no nut on it and the bolt had pretty much worked its way out , the other mount the bolt was loose and the mount was split and hanging in pieces. Once its up on the ramps its easy to check this.
Turned out to be very simple.
The ticking was a leaking exhaust gasket - diagnosed in about 5 seconds by a mechanic with a stethoscope
All the other problems turned out to be engine mount related. One mount had no nut on it and the bolt had pretty much worked its way out , the other mount the bolt was loose and the mount was split and hanging in pieces. Once its up on the ramps its easy to check this.
chr1sb said:
Talk to Richard at Dulfords - not far from Bristol.
Heard very good things about Dulfords too.I would avoid Webbs though, a friend who had his TVR serviced there was less than impressed and when I called about a potential service (thought it may have been 1 bad experience and they are normally OK), I found the person on the phone to be quite rude and thus two strikes....wouldn't go near them now.
zippy500 said:
Neil Garner is a good bet, up in Kemble. Great guy and honest too which these days is a pleasure. I had a bad experience with Webbs so personally would not recommend them. But its your car so you decide.
I would recommend Neil Garner in Kemble - knows his stuff. If you are interested he is having a talk at his workshop on Wed 11th Feb at 8pm about TVR's on performance mods etc.Edited by zippy500 on Tuesday 3rd February 10:46
Thanks to everyone for the advice,
Spoke to Neil Garner today and booked in for next week sometime. Might make it Wednesday so I can attend the TVR Tuning Mods lecture too!
Very friendly and knowledgeable! He said it could be a possible 'follower preload problem holding valve open a bit' scenario! That would certainly fit the symptoms.
Ryan
Spoke to Neil Garner today and booked in for next week sometime. Might make it Wednesday so I can attend the TVR Tuning Mods lecture too!
Very friendly and knowledgeable! He said it could be a possible 'follower preload problem holding valve open a bit' scenario! That would certainly fit the symptoms.
Ryan
Gassing Station | Chimaera | Top of Page | What's New | My Stuff



