Setting up suspension
Setting up suspension
Author
Discussion

scotty_d

Original Poster:

6,795 posts

225 months

Friday 6th February 2009
quotequote all
Hi

I am looking for advice on how to set my Normal GAZ suspension up for road use, What is the best way to adjust the spring first of all how far up do you screw the big nut on both front and rear?
What is the best setting to start with on the damper adjustment and from which way I.E – TO+
Or +TO-?

Cheers Scotty

V8 Animal

6,015 posts

241 months

Friday 6th February 2009
quotequote all
Have a word with derek.
http://www.absolutelyshocks.com/

daz the plumber

14,997 posts

262 months

Friday 6th February 2009
quotequote all
i have mine set at 150mm rear and 140mm front from the out rigger triangle plate ,i cut a bit of pipe the correct length,jack the car up slack the locking nut and adjust, then i eather go for a drive or just push the suspension up and down a few times .ive got mine set 15 clicks from soft rear and 14 clicks from soft front .

sporty stuff

54 posts

214 months

Friday 6th February 2009
quotequote all
same as mine big difference in road holding

Chimjunkie

2,879 posts

242 months

Friday 6th February 2009
quotequote all
And of course if you adjust the ride height you would be wise to get a full geometry set up done. Topcats get my vote for that.

scotty_d

Original Poster:

6,795 posts

225 months

Friday 6th February 2009
quotequote all
I just need a base setting to drive it the 65 miles to Dreadnought, Brian is setting my geo up. i stay north of the border!smile



Edited by scotty_d on Saturday 7th February 10:19

Ab Shocks

1,686 posts

251 months

Saturday 7th February 2009
quotequote all
scotty_d said:
I just need a base setting to drive it the 65 miles to Dreadnought, Brain is setting my geo up. i stay north of the border!smile

Edited by scotty_d on Friday 6th February 22:36
If these shocks are new ones with 21 adjustments, I would just set them at 5-6 clicks from soft on the front by turning the adjuster clockwise and 6-7 clicks up on the rear.
I would set the ride height at 150mm front, from corner of outrigger and 160mm rear, again from corner of outrigger.

That should be safe enough to get you down to Brian.

scotty_d

Original Poster:

6,795 posts

225 months

Saturday 7th February 2009
quotequote all
Ab Shocks said:
scotty_d said:
I just need a base setting to drive it the 65 miles to Dreadnought, Brain is setting my geo up. i stay north of the border!smile

Edited by scotty_d on Friday 6th February 22:36
If these shocks are new ones with 21 adjustments, I would just set them at 5-6 clicks from soft on the front by turning the adjuster clockwise and 6-7 clicks up on the rear.
I would set the ride height at 150mm front, from corner of outrigger and 160mm rear, again from corner of outrigger.

That should be safe enough to get you down to Brian.
Thanks for that just a quick one what do you mean from the out rigger corner to where? sorry i dont understand.

the car is on axle stands as i have just refurbed the wishbones and have fitted the new shocks to the car allready just no idea what to do with them.

Ab Shocks

1,686 posts

251 months

Saturday 7th February 2009
quotequote all
Sorry, late night posts can be unclear.

I meant measured from corner of outrigger to ground.

Generally, if you take a front shock and pull it full open and wind up the spring seat until there is approx 25-30mm between the lockring and where the shock body screws into the base and about 40mm on the rear, you won't be far out.

Run the car round the block and then check the ride height front and back at the outrigger to ground and if you are 150mm front and 160mm rear, that will do for now. I would try and go the most undulating route I could find to Brian's place to ensure the springs had settled.

spend

12,581 posts

282 months

Saturday 7th February 2009
quotequote all
You have to drop the car weight onto the wheels to torque up all the chassis & suspension bolts anyway. Thats when you measure on as level a surface as poss hehe ahhh but where is the corner - its only rough so anywhere you decide as long as the measurement is consistent (re the reference point) on each corner IYSWIM.

Not the way I would do it BTW wink wheels absolutely leveled on ramps, straight plank across wheels under car, and measure to the main chassis rails. I have a jig using a window board with bits of plastic screwed on at 90degs that have my marks on to set the heights. I'll be buggered if it ever gets warped yikesrofl

scotty_d

Original Poster:

6,795 posts

225 months

Saturday 7th February 2009
quotequote all
Cheers thats now clear i will have to wait till i put the brakes back on the car first laugh

My other option is to put the car on a trailer and take it up to him