Setting up fuel reg
Setting up fuel reg
Author
Discussion

Meatball

Original Poster:

1,638 posts

241 months

Saturday 7th February 2009
quotequote all
Anyone know the procedure for setting the 1:1 fuel regulator?
With ignition on (car not running) ive set the pressure to 3 bar which then drops to 0.
With the car running im getting 2.8 bar is this the correct measurement or the one before???
Or should they be the same and somethings wrong??
Does anyone have a clue what im going on aboutconfusedhehe

spend

12,581 posts

282 months

Saturday 7th February 2009
quotequote all
Is your gauge reading pressure vs manifold, or atmosphere? its the pressure compared to the injector nozzles 'atmosphere' which is important.

Meatball

Original Poster:

1,638 posts

241 months

Saturday 7th February 2009
quotequote all
spend said:
Is your gauge reading pressure vs manifold, or atmosphere? its the pressure compared to the injector nozzles 'atmosphere' which is important.
Dave, sorry i dont have a clue what you mean confused.

These readings were taken with the hose to plenum connected if thats what you mean,the regulator is a standard fse with screw in pressure dial.

spend

12,581 posts

282 months

Saturday 7th February 2009
quotequote all
To deliver a known amount of fuel its the pressure at the nozzle that matters, that is relative to the inlet not atmosphere. There is a vacuum in the inlet port as YOUR engine sucks (hehe) - so the pressure is regulated against manifold pressure (hence the pipe). If your gauge is measuring absolute rather than the referenced pressure it is only normal that they differ wink Clamp the vacuum pipe and you should see different results. Seeing 2.8 bar after setting at 3.0 bar just suggests engine is sucking at 0.2 bar.

I connect a vacuum gauge to the TB and do mental arithmetic

daz the plumber

14,997 posts

262 months

Saturday 7th February 2009
quotequote all
fit the guage ,petrol will spirt everywhere so use a rag, run the engine get it warm ,romove the vac pipe and ive set mine at 37psi as advised by v8 d , re fit the vacume pipe , turn the engine off to cool, re fit plug .any trimming need to be carried out by specialist,

spend

12,581 posts

282 months

Saturday 7th February 2009
quotequote all
Pull the fuel pump fuse or relay & let the engine get rid of the pressurized fuel in the rail, it only takes a mo & is a lot less messy / dangerous wink

Meatball

Original Poster:

1,638 posts

241 months

Saturday 7th February 2009
quotequote all
Nice one thanks

GreenV8S

31,027 posts

315 months

Saturday 7th February 2009
quotequote all
If you just switch the ignition on without starting the engine you will see the pressure come up for a couple of seconds while the pump primes, then the pump switches off. Depending what mood the regulator is in you may see it hold the pressure for a while when the pump stops, or leak straight back down to zero. Either way it's shile the pump is running that you need to check the pressure. By doing it with the engine stopped you avoid any issues of compensating for manifold pressure or disconnecting the vac line (resulting in over fuelling).

blitzracing

6,422 posts

251 months

Saturday 7th February 2009
quotequote all
. Daz has it correct, set it for 37 psi to start (thats 2.4 bar) with the vacuum pipe disconnected at idle. Its impossible to set with the pipe connected due to the variance in plenum vacuum as Spend says. Once you have set it then get a test meter connected across the black and white wires to the lambda probe (the extension cable socket is a good access point by the plenum) with long wires, so a passenger can read the meter. Then take the car for a full power run, and check you get at least .8 volts on the meter under full load up to peak RPM. If the voltage starts to drop then put the fuel pressure up in small steps until its steady. If you go too far the reading will get up to a 1.2 volts, so try and get it between the about .8 and 1 volt. 2 psi either way is enough to see significant change in readings. Check both banks as well, as the fuelling is not always even. Its better to error with a higher voltage, and never let it run for any period below .8 volts at full power. NOTE. Below 3400 rpm, or 3/4 throttle the voltage will swing between .2 and .8 volts- thats normal. The difficult bit is getting enough road to allow the readings to settle under full power, and a quick blast will give a false reading as the ECU enriches the mixture for a couple of seconds. A hill in say 3rd gear between 4000 and 6000 rpm with even acceleration should do. Dont try and guess without these voltage readings, as you may end up running lean and damage your engine, and don’t rely on a gut feeling that its quicker !.

mark

spend

12,581 posts

282 months

Saturday 7th February 2009
quotequote all
blitzracing said:
Its impossible to set with the pipe connected due to the variance in plenum vacuum as Spend says.
No I didn't! I even explained how to using an extra gauge to measure the vacuum. That way you can even check the pressure differential at different loads confused

blitzracing

6,422 posts

251 months

Saturday 7th February 2009
quotequote all
Ok, I did not read the very very small print!!

GreenV8S

31,027 posts

315 months

Saturday 7th February 2009
quotequote all
spend said:
blitzracing said:
Its impossible to set with the pipe connected due to the variance in plenum vacuum as Spend says.
No I didn't! I even explained how to using an extra gauge to measure the vacuum. That way you can even check the pressure differential at different loads confused
Has anyone come across a differential pressure gauge (or even just a differential pressure switch) for sensible money? I'd quite like to be able to put a fuel pressure alarm on mine but with a manifold-referenced regulator it does need to be a differential one.

blitzracing

6,422 posts

251 months

Saturday 7th February 2009
quotequote all
Would'nt a lambda gauge be easier?

GreenV8S

31,027 posts

315 months

Saturday 7th February 2009
quotequote all
blitzracing said:
Would'nt a lambda gauge be easier?
Yes but it doesn't do the same job.

spend

12,581 posts

282 months

Saturday 7th February 2009
quotequote all
I've seen a static one Pete, but they were so expensive I just used 2 gauges - I know they may not be calibrated as accurately but good enough IMHO. I would imagine electronic senders for vac and fuel pressure would be of similar benefit (just log them?)

blitzracing

6,422 posts

251 months

Saturday 7th February 2009
quotequote all
GreenV8S said:
blitzracing said:
Would'nt a lambda gauge be easier?
Yes but it doesn't do the same job.
I thought you where just worried about the engine leaning out ? I used a oil pressure gauge in the cab fed from the fuel rail and it was pretty obvious when the pressure was dipping under wide open throttle, when it should have been at 37 psi. Dont know what 'elf and saftey would say about this however !

Meatball

Original Poster:

1,638 posts

241 months

Saturday 7th February 2009
quotequote all
The fueling dosent have to be 100% for the moment just in a normal/safe range (which i thought 3 bar would be ok for my car paperbag).

Im looking to have it wired up to a wideband sensor and set up on the rolling road in the next couple of weeks.

Thanks chaps


GreenV8S

31,027 posts

315 months

Saturday 7th February 2009
quotequote all
blitzracing said:
I thought you where just worried about the engine leaning out ? I used a oil pressure gauge in the cab fed from the fuel rail and it was pretty obvious when the pressure was dipping under wide open throttle, when it should have been at 37 psi. Dont know what 'elf and saftey would say about this however !
I'm after several things really. I want to know whether my fuel pump is up to the job. If it starts to lose pressure at the top of the power band I'd like to know about it rather than just keep increasing the injector d/c or going to bigger injectors. I got a remote pressure gauge with the intention of fitting it temporarily just to test the pump out (it comes with dire warnings against long term use) but I never could get the remote pipe to seal properly and decided not to trust it.

As well as testing it today, I'd like to have a way of detecting if the pump performance has dropped off - this would most likely show as loss of flow resulting in a pressure drop at the top of the power band.

So, what I'd really like is a differential pressure switch which I can use to reassure myself that the pump is coping OK and also to tell the ECU to go into 'safe' mode if the pump does brown out. The problem with forced induction is that lots of systems all have to be in perfect working order to keep the engine safe, so my plan is to monitor and alarm as many of them as possible.

locodude

510 posts

226 months

Sunday 8th February 2009
quotequote all
Just as a matter of interest, what should the standard regulator be limiting the pressure to and what what is the optimal setting for a standard 400? I assume the Lambda settings are the same as previously posted.

GreenV8S

31,027 posts

315 months

Sunday 8th February 2009
quotequote all
The standard pressure is 2.5 bar (37 psi).