Tappets & Manifolds
Discussion
Hi everyone, after 18 fantastic months of owning a Chim ('97 400 serp), and at least as long observing this forum (and learning lots, thanks!), I've plucked up enough courage to ask a couple of questions of my own.
When I bought the car it suffered from both valve train and 'leaky exhaust manifold' (ie could be gasket or manifold) noise. I took it for its annual service at a very well respected indie in the SW (who had been looking after the car for some time) and after lots of helpful chat, decided to invest in a stealth cam, vernier timing gear, new chain, rocker arms, Magnecors, silicone induction kit, Steve Heath drop links & new engine mounts. Fantastic! The car goes like a train with good top end and idles smoothly. But the valve gear is still exactly as noisy (quite annoying with the hood down when the engine's hot at low speeds) and I've clearly got an exhaust leak from around the LH manifold which, as you'd expect is more apparent under load.
So, the questions to which I'd be really grateful for advice on:
Is it possible to have quiet valve gear or do I have to put up with it? Are there any appropriate mods or adjustments (eg solid lifters)?
Spring service is coming up - if the leak is not from the gasket I am willing to invest in new manifolds and new cats - (don't want to go noisier) - are stainless worth the expense? Where's the best supplier - I've seen ACT's ads, but there don't seem many companies that do (ss or mild steel) off the shelf?
Sorry for the length of this post; I'll try better next time!
Thanks
When I bought the car it suffered from both valve train and 'leaky exhaust manifold' (ie could be gasket or manifold) noise. I took it for its annual service at a very well respected indie in the SW (who had been looking after the car for some time) and after lots of helpful chat, decided to invest in a stealth cam, vernier timing gear, new chain, rocker arms, Magnecors, silicone induction kit, Steve Heath drop links & new engine mounts. Fantastic! The car goes like a train with good top end and idles smoothly. But the valve gear is still exactly as noisy (quite annoying with the hood down when the engine's hot at low speeds) and I've clearly got an exhaust leak from around the LH manifold which, as you'd expect is more apparent under load.
So, the questions to which I'd be really grateful for advice on:
Is it possible to have quiet valve gear or do I have to put up with it? Are there any appropriate mods or adjustments (eg solid lifters)?
Spring service is coming up - if the leak is not from the gasket I am willing to invest in new manifolds and new cats - (don't want to go noisier) - are stainless worth the expense? Where's the best supplier - I've seen ACT's ads, but there don't seem many companies that do (ss or mild steel) off the shelf?
Sorry for the length of this post; I'll try better next time!
Thanks
I would be inclined to cure your blowing manifolds be it new gaskets etc before commenting on valve gear noise(can sound similar some times)the RV8 dont suffer from noisy cam gear unless you have a problem,if thats the case and the work was done recently then take it back to the garage that carried out the work for you
or failing that run it past them anyway to give you there professional opinion as to whats causing said noise and go from there.
or failing that run it past them anyway to give you there professional opinion as to whats causing said noise and go from there.Thanks. Yes, I took it back a week after all that work last April. Resident RV8 expert's view was that this engine's valve gear is noisy anyway (and confirmed the noise was valvegear related). I will let them know I'm still not happy with it, trouble is I've not been able to compare with a 'normal' engine.
If it's had all that work done on the valve train and still noisy (and assuming you *have* confirmed the noise is valve train related) then I'd be checking the preloads. It's possible that either these have not been set correctly in the first place, or that there is so much difference between cylinders that it wasn't possible to get them all right.
GreenV8S said:
If it's had all that work done on the valve train and still noisy (and assuming you *have* confirmed the noise is valve train related) then I'd be checking the preloads. It's possible that either these have not been set correctly in the first place, or that there is so much difference between cylinders that it wasn't possible to get them all right.
which was why i mentioned taking the car back to the garage again Gassing Station | Chimaera | Top of Page | What's New | My Stuff




