Discussion
When I finally get round to putting my engine back together I'm going to need rockers & shafts as a minimum on the top end.
I've seen steel ones advertised in a few places - can I assume due to the lack of threads (none) that I have found on these they are best avoided?
You don't want more weight in the valve train anyway do you?
I planned to go for standard rockers - I assume the steel ones are around because they can be made cheaply and no other reason?
Or am I missing something?
I've seen steel ones advertised in a few places - can I assume due to the lack of threads (none) that I have found on these they are best avoided?
You don't want more weight in the valve train anyway do you?
I planned to go for standard rockers - I assume the steel ones are around because they can be made cheaply and no other reason?
Or am I missing something?
Steel are preferable as they do not suffer with premature lost pads which can be an issue with alloy ones.
It is not a common problem, but it does occur occassionally. It has been discussed several times on the forums but the search facility only goes back 2 yrs and that's classified as Jan '09 and all of 08 . . Also don't confuse the valve gear in a TVR RV8 with a TVR SP6 . . . very different in terms of quality
Next up the tree are roller rockers which then take away the side loading on the top of valve.
It is not a common problem, but it does occur occassionally. It has been discussed several times on the forums but the search facility only goes back 2 yrs and that's classified as Jan '09 and all of 08 . . Also don't confuse the valve gear in a TVR RV8 with a TVR SP6 . . . very different in terms of quality

Next up the tree are roller rockers which then take away the side loading on the top of valve.
definately a vote for steel here as well, I replaced my standard ones because one of the pads came away from the rocker, then only 400 miles later found 3 of the new ones had lost their pads!! threw them in the bin and bought steel ones, fit and forget scenario
I have some roller rockers if you`re interested.

I have some roller rockers if you`re interested.
Edited by clive f on Tuesday 10th February 14:22
If you are changing the rockers, its odds on the shafts will be worn as well.... then roundness of the posts... 
Dom replied to a thread on here a couple of years ago that he was happy with the alloy rockers and that problems were down to a 'bad' batch. Personally I would always prefer lighter alloy to cut weight in the valvetrain, but each to their own there is not such a great deal in it..

Dom replied to a thread on here a couple of years ago that he was happy with the alloy rockers and that problems were down to a 'bad' batch. Personally I would always prefer lighter alloy to cut weight in the valvetrain, but each to their own there is not such a great deal in it..
dhf said:
Clive,what are the benefits of your roller rockers ?
no friction so more power, the rollers roll over the top of the valve head, and the preload, valve crearance, can be adjusted at the top of the rocker, these are more of a benefit to someone with solid lifters, as then to check valve clearances you dont have to remove the inlet manifold and valley gasket to check the pre load on the lifters as with the normal proceedure for hydraulic lifters.a benefit really to any type of lifters, and increase in power output.
clive f said:
dhf said:
Clive,what are the benefits of your roller rockers ?
no friction so more power, dhf said:
Clive,thanks understand it all now.i am actually installing a tame cam for the supercharger.
I think thats a requirement isn't it?My understanding is if you have a lairy cam with overlap (where both exhaust and inlet valves are open at the same time) the pressurised induction blows your fuel / air mixture straight out the exhaust?
Have I interpreted this correctly?
Gassing Station | Chimaera | Top of Page | What's New | My Stuff





