Putting on axel stands
Putting on axel stands
Author
Discussion

BeastMaster

Original Poster:

443 posts

218 months

Wednesday 11th February 2009
quotequote all
Hi Guys - need some advise on how to put the Chim up on axel stands. I have small trolly and large bottle jacks, a set of ramps and 4 axel stands. Have only used the ramps so far to change oil filter etc but have no idea how to put her onto 4 stands. Any advise welcome, just need to get some confidence in a tried method - Many thanks Beastmaster

scotty_d

6,795 posts

225 months

Wednesday 11th February 2009
quotequote all
If your chassis is in good condition the corner or each out rigger will be fine. if your worried put them on the the main chassis. when the cars go on two post lifts the are picked up by each corner of the out rigger and are fine.

Barkychoc

7,848 posts

235 months

Wednesday 11th February 2009
quotequote all
Put some cardboard on the axle stand as well if you are worried about it marking the chassis.

WOO5IE

967 posts

228 months

Wednesday 11th February 2009
quotequote all
AS you have already used the ramps they must have the required angle i.e. not too steep.
Front. Once on the ramps use the trolley jack on the front main chassis cross member just behind the radiator.

Just jack up a little until high enough to get the axle stands under the 2 main chassis members that run the length of the car. Then just lower trolley jack so that car rests on the axle stands. ( Dont forget some packing to protect the powder cost on the chassis).

If your trolley jack is low enough you can get it directly under the front cross member without having to use the ramps. My jack just goes under but a lot dont.

A bit cold to be getting under cars unless in a heated garage though.

Trev

glow worm

7,524 posts

258 months

Thursday 12th February 2009
quotequote all
I would take the car up in stages...Trolley jack(centre) or a pair of bottle jacks from front front (make sure handbrake on,in gear and wedge rear wheels), get axle stands under once the wheels are off. Move to the back with bottle jacks (doubt you'll get a trolley jack under the rear unless its long reach) at each outrigger corner. Bring both sides up together without out tilting the car sideways...and be very careful. You don't want it slipping forward.

Foolishly I once put my BMW on axle stands and tried to do it from each corner ,starting on one side....I finished up with the car falling off and nearly crushing me against a wall.

Nowadays I just use my 4 post lift and just drop it down on to axle stands...far easier.

PS If you're taking off the wheels, get the wheels 1" off the ground to allow for the springs dropping a bit...Otherwise it might be a pig putting your wheels back on.



Edited by glow worm on Thursday 12th February 09:53

BeastMaster

Original Poster:

443 posts

218 months

Thursday 12th February 2009
quotequote all
Thanks all for your advise. Looking to clean up and repaint outriggers soon as starting to show some surface rust and decided that I wanted the underside totaly accessable rather than doing a bit at a time.
My car is quite old 1994 57K miles amd seems to be quite solid, so a bit of a shock to see some of the horror stories on cars a lot newer. This has made me wonder if the newer cars were not quite as well finished at the factory - any thoughts - Andy

bobfather

11,197 posts

286 months

Thursday 12th February 2009
quotequote all
Having done this from the outriggers and from the ladder frame I think there are pros & cons for both.

Using the corners of the outriggers you may find the chassis members are in poor condition, this is the prime place for hidden rot. If you see or suspect rot then don't use the outrigger corners as support points. If the outriggers are in good order there is no issue using the corners and you will have a very stable platform to work from.

Using the ladder frame (centre box section rails) you can be confident that the chassis is capable of supporting the load. Unfortunately though the working platform can become quite unstable for some tasks where the work requires you to push and pull on the car. Suspension work for example. If you are doing suspension work using axel stands on the ladder frame then I'd suggest leaving one set of wheels on the ground to stabilise the platform.

glow worm

7,524 posts

258 months

Thursday 12th February 2009
quotequote all
BeastMaster said:
Thanks all for your advise. Looking to clean up and repaint outriggers soon as starting to show some surface rust and decided that I wanted the underside totaly accessable rather than doing a bit at a time.
My car is quite old 1994 57K miles amd seems to be quite solid, so a bit of a shock to see some of the horror stories on cars a lot newer. This has made me wonder if the newer cars were not quite as well finished at the factory - any thoughts - Andy
The coating on my 2006 Tuscan is far better than my 2001 Chim...It is more like a plastic coating...It's when you see cracks in the powder coating , it will peel off in big lumps. My Hammerite (White & Black mix is far better). I think condition depends more on the previous owners... Personally I don't like Waxoxl, because it hides corrosion, I prefer to keep it spotless biggrin . Oil/Waxoyl inside the outriggers might be a good idea, provided it doesn't drip everywhere afterwards.


over_the_hill

3,340 posts

277 months

Thursday 12th February 2009
quotequote all


Axel Standing

getmecoat