Chimaera swiming pool
Discussion
Monday was a little wet around my way and on the way home the chim did a lot of blowing water and steam out of the bonnet vents. This morning was rather cold and after scraping the outside of the windows I then realised that much of the ice was on the inside. It would appear that somewhere in it's Monday splash and dash home the foot-wells picked up a fair amount of water. This mainly seems to be the drivers side but the passenger side is wet as well.
Is this normal? Is there anything that can be done to stop it (except not driving through huge puddles at speed)?
Is this normal? Is there anything that can be done to stop it (except not driving through huge puddles at speed)?
Not advisable to drive through deep puddles at anything over a crawl in these cars. If you suck up water through the low mounted air filter your engine will hydraulic and be fooked. Also not good to subject the manifolds/exhaust system to rapid cooling. But yes, there are many opportunities for water to come into the footwell.
Let's be a bit more practical guys as you can't always anticipate rain and fit a car cover. You need to resolve the issue.
I bought my current car in November and it saw its first serious rain (ever!) three weeks ago. I discovered a bit of a puddle in the offside footwell the following morning.
I set about (re)sealing all ancilliaries that go through the underbonnet driver's wing (master cylinder cover etc) and also found a slight gap in the lower windscreen surround on that side. Last Friday it rained again and, once more, the footwell was wet.
Thinking outside of the box, I jacked the car up the following day and checked if the washers and nuts, holding the seat in place, had been sealed. They hadn't. A good application of Sicaflex seems to have done the trick as, after driving to work on Monday, which was very wet, no further water has entered.
I bought my current car in November and it saw its first serious rain (ever!) three weeks ago. I discovered a bit of a puddle in the offside footwell the following morning.
I set about (re)sealing all ancilliaries that go through the underbonnet driver's wing (master cylinder cover etc) and also found a slight gap in the lower windscreen surround on that side. Last Friday it rained again and, once more, the footwell was wet.
Thinking outside of the box, I jacked the car up the following day and checked if the washers and nuts, holding the seat in place, had been sealed. They hadn't. A good application of Sicaflex seems to have done the trick as, after driving to work on Monday, which was very wet, no further water has entered.
If you do a search there are a few topics on the subject. Opinions are split but after chasing a driver's footwell leak for weeks it proved to be the seal at the bottom of the windscreen. I just resealed it with sikaflex and bingo. The best way I found to test it was to simply pour a bucket of water on the windscreen and then watch as the water drip down around the brake and clutch pedals. It needs redoing again this year but mine was dry for months.
Hope that helps.
James
Hope that helps.
James
Thanks for that. The Silkaflex turned up on Tuesday and the rubber around the screen is a little ragged. Maybe I'll get some dry weather on the weekend to seal it. I'm a little concerned that I'm going to spend the 14th with the car and not with the girlfriend. I think she's already jealous.
In the meantime I guess it's carpets out and a couple of towels down.
In the meantime I guess it's carpets out and a couple of towels down.
The drive noise is coming from the back but only at 1500 revs (pretty much on the nose). This seems to be something clunking due to shunting. I will get it looked at as I'm not confident to mess with the diff or for that mater get under the car at the moment.
The water thing makes sense as the rubber around the window is flapping on that side. However I did check around the footwell and it doesn't seem to have dripped from anywhere more come up. I will seal the windscreen tomorrow (weather permiting) and monitor it (Silkaflex was £7).
The mirror seems to have settled into a notch that doesn't let it droop. I have however purchased a new toad stool (sounds trippy) and will take the door panel off and see if it's a tighten or replace job (toad stool £8).
The slow window is on the same side so when I have the panel off I will WD40 the motor and I also got 2 meters of replacement window felt so will try to replace that at the same time (£3/m for the felt). Has anyone got any experience of doing this? Is it covered in the Bible?
The only other thing that is slightly bugging me is that on very cold days (we've had a few) the car tends to idle at either 2000 or 1500 revs. If I turn it off and restart (I learnt something from developing computers) it idles at 1000 revs. Is this likely to be an issue with the ECU (Ctrl, Alt Delete seems to fix) or is it just that the stepper thingy needs taking out and cleaning.
That said it's an amazing car and I'm really happy with it. When I first got my Alfa it cost me £2k in the first month. So far the parts to resolve the above issues have been under £50
The water thing makes sense as the rubber around the window is flapping on that side. However I did check around the footwell and it doesn't seem to have dripped from anywhere more come up. I will seal the windscreen tomorrow (weather permiting) and monitor it (Silkaflex was £7).
The mirror seems to have settled into a notch that doesn't let it droop. I have however purchased a new toad stool (sounds trippy) and will take the door panel off and see if it's a tighten or replace job (toad stool £8).
The slow window is on the same side so when I have the panel off I will WD40 the motor and I also got 2 meters of replacement window felt so will try to replace that at the same time (£3/m for the felt). Has anyone got any experience of doing this? Is it covered in the Bible?
The only other thing that is slightly bugging me is that on very cold days (we've had a few) the car tends to idle at either 2000 or 1500 revs. If I turn it off and restart (I learnt something from developing computers) it idles at 1000 revs. Is this likely to be an issue with the ECU (Ctrl, Alt Delete seems to fix) or is it just that the stepper thingy needs taking out and cleaning.
That said it's an amazing car and I'm really happy with it. When I first got my Alfa it cost me £2k in the first month. So far the parts to resolve the above issues have been under £50

Gassing Station | Chimaera | Top of Page | What's New | My Stuff




