Drivers window not working - not door electrical connectors!
Drivers window not working - not door electrical connectors!
Author
Discussion

M@H

Original Poster:

11,298 posts

303 months

Monday 16th February 2009
quotequote all
All,

My drivers side electric window has stopped working (it was a fair few weeks ago it stopped but am just getting round to looking at it)

So, my findings so far are this:

The window mechanism itself is just fine - if a add 12v to the connections behind the speaker I can wind it up and down.
The loom connections in the door are just fine. (and all other door electrics are ok)
The connections to the center console switch are all clean and tidy, however there is no 12v at the switch.

Next thoughts are based round the mass of electricians tape that makes up the loom, and also the connections behind the fuseboard in the back of the footwell, I don't really fancy either much so does anyone have any pearls of wisdoms please before I get into it.

(And before someoene suggests a Fuse: from memory it is a shared fuse so I have ruled that out as everything else in the car electricals works just fine)

Many thanks,
Matt.

Podie

46,649 posts

306 months

Monday 16th February 2009
quotequote all
Tried replacing the switch?

I wouldn't dismiss the fuse thing... my Chimaera had some "interesting" fusing connections - quite far removed from the manual and Steve Heath's publication.

T_Pot

2,542 posts

228 months

Monday 16th February 2009
quotequote all
try running a live from the fuse box to the switch?

spend

12,581 posts

282 months

Monday 16th February 2009
quotequote all
If the other window works the fuse will be fine wink Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.

M@H

Original Poster:

11,298 posts

303 months

Monday 16th February 2009
quotequote all
spend said:
If the other window works the fuse will be fine wink Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.
Sounds good, is that within the tape run from both the switch bunches before it goes into the lower dash alongside the top of the passenger footwell? (i.e still under/near the centre console)

Cheers,
Matt.


M@H

Original Poster:

11,298 posts

303 months

Monday 16th February 2009
quotequote all
T_Pot said:
try running a live from the fuse box to the switch?
The problem is upstream of the switch I am afraid. As put originally there is no 12v at the switch, however your method would indeed tell me if there was a fault downstream or with the switch itself. smile

Matt.

spend

12,581 posts

282 months

Monday 16th February 2009
quotequote all
M@H said:
spend said:
If the other window works the fuse will be fine wink Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.
Sounds good, is that within the tape run from both the switch bunches before it goes into the lower dash alongside the top of the passenger footwell? (i.e still under/near the centre console)

Cheers,
Matt.
Yes, on mine it was a link from switch to switch, ie fused supply + link wire crimped onto one switch terminal, link looped back in/out of loom to the other switch. Loom might have evolved a bit in later cars , but should be similar..

If there is evidence of copius amounts of insulating tape rather than loom tape (not sticky) somebody has had their dirty hands in there already! hehe

M@H

Original Poster:

11,298 posts

303 months

Monday 16th February 2009
quotequote all
spend said:
M@H said:
spend said:
If the other window works the fuse will be fine wink Strip the tape loom back from the switches and you will see where the +12v is spliced to go to both switches. Your fault will likely be in that short part of loom.
Sounds good, is that within the tape run from both the switch bunches before it goes into the lower dash alongside the top of the passenger footwell? (i.e still under/near the centre console)

Cheers,
Matt.
should be similar..
err, this is TVR we are talking about hehe

Thanks, I shall have another look tonight.

spend

12,581 posts

282 months

Monday 16th February 2009
quotequote all
M@H said:
err, this is TVR we are talking about hehe
I was talking in schema rather than execution (and hinting at exactly that phenomena) rofl

M@H

Original Poster:

11,298 posts

303 months

Monday 16th February 2009
quotequote all
spend said:
M@H said:
err, this is TVR we are talking about hehe
I was talking in schema rather than execution (and hinting at exactly that phenomena) rofl
True smile my wiring doesn't match any of the ones in the Bible anyway (well the relay layouts don't at least)


spend

12,581 posts

282 months

Monday 16th February 2009
quotequote all
M@H said:
spend said:
M@H said:
err, this is TVR we are talking about hehe
I was talking in schema rather than execution (and hinting at exactly that phenomena) rofl
True smile my wiring doesn't match any of the ones in the Bible anyway (well the relay layouts don't at least)
The bible diagram is surprisingly adequate if you change the fusebox locations to suit your own fusebox layout I found. Of course the newfangled girly RIBBON cable yikes owners can go whistlehehe

M@H

Original Poster:

11,298 posts

303 months

Friday 27th February 2009
quotequote all
...so I was actually getting 12v physically at the switch itself, however as discovered, nothing much after it.

After 2 hours of p!ssing about I have found the Culprit:


note the burn marks on the outer casing where the internals have melted it


it is a full closure module for the alarm system. Hidden well away in the lower dash across from the inertia cutoff switch.. sadly the car now looks like this so I've got some sorting out to do ..aah well.



Matt.

Edited by M@H on Friday 27th February 14:28

scotty_d

6,795 posts

225 months

Friday 27th February 2009
quotequote all
At least you got to the bottom of it. mine looked like that for the last few months, I had my first drive in it today since september now i have a problem cant get this off my face biggrin well worth all that hard work just need some dry weather now.