How does the carbon canister work.
How does the carbon canister work.
Author
Discussion

Pink_Floyd

Original Poster:

900 posts

252 months

Monday 16th February 2009
quotequote all
There seems to have been several discussions on the carbon canister but none explain how it works. There is a 1 way valve on the neck of the tank which I assume lets air into the tank as the tank empties. The canister has 2 other pipes, 1 to atmosphere and 1 to the plenum. So where exactly does air flow throught the system and when.

daz the plumber

14,997 posts

262 months

Tuesday 17th February 2009
quotequote all
think it works as a easy start , well thats what tvr shop said .

spend

12,581 posts

282 months

Tuesday 17th February 2009
quotequote all
Pink_Floyd said:
There is a 1 way valve on the neck of the tank which I assume lets air into the tank as the tank empties.
No its a solenoid valve which the ecu opens so that air is sucked into the plenum. This clears out the petrol vapour trapped in the charcoal filter. The only on-way valve I have seen are the connectors on the trumpet base.

The tank is enclosed and connected via pipe to charcoal filter which is then 'open' to atmosphere. When the solenoid is opened the engine sucks from atmosphere since tank is a 'dead end'.. This is a simple way of trapping fumes and then using them up in the burn rather than wasting them &/or pollution. Rest of the time the tank can inhale & exhale (via the vent to atmosphere through the charcoal) so it is actually used when you fill & as you empty the tank.

It also acts as filter to stop all sorts of grit / dust / st / water being drawn into the tank & your golden juice wink


450Nick

4,027 posts

243 months

Tuesday 17th February 2009
quotequote all
That sounds about right, just to add there is a one way valve in the system and that's the rollover valve just by the tank. This is inline with the pipe that supplies the carbon canister and stops any crap or water vapour getting into the tank (and obviously stops fuel getting out in the event of a rollover).

None of the pre-cats had carbon canisters as they simply had vented fuel filler caps (they were put in for emissions control purposes). These worked fine, but unfortunately it allowed some fuel vapour to escape into the boot which wasn't very nice. I've removed my CC but have relocated the vent pipe to the front passenger wheel well. This keeps any traces of fuel vapour away from the cabin, but still vents the tank just fine and makes sure that nothing will get back to the tank as its a long run!

project 112

83 posts

213 months

Tuesday 17th February 2009
quotequote all
so let me get this striaght, the outlet marked tank connects, you guesed it, to the tank via a one way valve the one marked air simply vents to atmosphere and the third connects the solinoid/purge valve to the outlet on the plenum base,yes? just to throw a spanner in the works i have twin tanks on my car how would this work or would it make no difference?

spend

12,581 posts

282 months

Wednesday 18th February 2009
quotequote all
I'm not sure I would call a roll over valve a one-way valve... Still cannot see where this one-way valve keeps getting in the conversation.

112, How do your tanks vent now or do they deflate? I would guess there is a balance pipe between the tanks for air, if not just tee the cannister to tank pipe so it goes to both tanks. Do note some CC's have an integral purge valve, and others are separate components.

project 112

83 posts

213 months

Wednesday 18th February 2009
quotequote all
spend, belive it or not the 2nd tank has, not that i can see anyway, any vent pipe all!! the only outlet apart from the fuel balance pipe is for the fuel return from the fuel rail on the engine. apart from welding a vent pipe to the top of the tank(don,t really want to do this as the tanks are now built in and awkward to get at) would it be possible to vent to the cannister from the filler neck, obviously as high up the neck as possible (to avoid fuel entering the vent pipe when filling up) and would this be safe?

spend

12,581 posts

282 months

Thursday 19th February 2009
quotequote all
Are you sure it doesn't just vent through the filler cap then? Whichever, you would expect both tanks to be the same?

project 112

83 posts

213 months

Friday 20th February 2009
quotequote all
spoke to the guy who made the tanks genuine mistake on his part should have put a vent outlet on the 2nd tank! other than removing the tank and welding in a pipe it looks like a vent out let fitted in the filler neck and teeing off to the cannister from this irked

Overhere

382 posts

254 months

Friday 20th February 2009
quotequote all
Hey Chris, is your ride on the road yet... time for us to go for a spin ;-)

Jack