how do i decat my exhaust?
how do i decat my exhaust?
Author
Discussion

brisy72

Original Poster:

10 posts

213 months

Tuesday 17th February 2009
quotequote all
is it recomended to decat the exhaust?

if yes how can i do it myself

eddyendo

477 posts

223 months

Tuesday 17th February 2009
quotequote all
should simply unbolt or slide out of exhaust clamps. Its the stubby box. Then get a garage ( or do it yourself) to make up a piece to fit in its place with the same end fittings, but with just a straight through pipe the same diamiter as the rest of the exhaust instead of the cat. Bear in mind you'll have to keep the cat safe as it'll need to go back on at MOT time.
Worth doing tho mind. We had 2 identical elises one decat and one standard, and they decat felt like a completely different car. I believe you get an extra 15bhp+ or maybe more on a chim with a big bore staight through system.
Hope this helps.

debaron

878 posts

228 months

Wednesday 18th February 2009
quotequote all
I believe you are supposed to remove the Pre-Cats too but not 100%. I'm sure someone will be along shortly to verify.

Ozmira

1,175 posts

220 months

Wednesday 18th February 2009
quotequote all
Just do a search on pre cats and you'll find loads of info.

locodude

510 posts

226 months

Wednesday 18th February 2009
quotequote all
eddyendo said:
should simply unbolt or slide out of exhaust clamps. Its the stubby box. Then get a garage ( or do it yourself) to make up a piece to fit in its place with the same end fittings, but with just a straight through pipe the same diamiter as the rest of the exhaust instead of the cat. Bear in mind you'll have to keep the cat safe as it'll need to go back on at MOT time.
Not possible with the Chim as the main cat is inside the 'Y piece' and is a bespoke item. Either get one that's already been done to replace it and change it back for MOT time or find a friendly MOT garage. Replacement Y pieces can also be bought from places such as ACT.

Edited by locodude on Wednesday 18th February 08:46

Talkwrench

910 posts

264 months

Wednesday 18th February 2009
quotequote all
On the subject of removing pre-cats, they can be an absolute arse to remove. They're incredibly well fixed in place and surprisingly tough when attacked by the usual 'big chisel' method.
Having removed two yesterday, after much cursing, the easiest method was to use a long masonry drill and basically drill them to bits. Wear a mask though - there'll be lots of dust and instinct tells me that its never going to be good for you to breath in the nasty grey stuff.....

VerySideways

10,272 posts

303 months

Wednesday 18th February 2009
quotequote all
Talkwrench said:
On the subject of removing pre-cats, they can be an absolute arse to remove. They're incredibly well fixed in place and surprisingly tough when attacked by the usual 'big chisel' method.
Having removed two yesterday, after much cursing, the easiest method was to use a long masonry drill and basically drill them to bits. Wear a mask though - there'll be lots of dust and instinct tells me that its never going to be good for you to breath in the nasty grey stuff.....
I did this a week ago and agree with you completely, word for word. Worth doing though, engine is breathing so much better as a result.

LordGrover

34,189 posts

243 months

Wednesday 18th February 2009
quotequote all
Interesting thread: Clicky.

eddyendo

477 posts

223 months

Wednesday 18th February 2009
quotequote all
excuse my lack of knowledege as never done it on a chim lol.

Overhere

382 posts

254 months

Friday 20th February 2009
quotequote all
But hold on, removing cats mean you fail MOT, right? I always thought if you do this you have to be ready once a year to put it back to pass MOT, which means it's actually illegal, right?

Removing pre-cats is another story, MOT is done with a warm engine and pre-cats are there to clean-up the exaust before the engine warms up.